Fujitsu PRIMERGY RX200 S3 Manuel utilisateur

PRIMERGY RX200 S3

Server

Options Guide

Edition August 2006

Comments…Suggestions…Corrections…

The User Documentation Department would like to

know your opinion of this manual. Your feedback helps

us optimize our documentation to suit your individual

needs.

Fax forms for sending us your comments are included in

the back of the manual.

There you will also find the addresses of the relevant

User Documentation Department.

Certified documentation

according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system

which complies with the requirements of the standard

DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

RX200 S3 OptionsGuide

Contents

1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Overview of the documentation . . . . . . . . . . . . . . . . . . 5

1.2 Extensions and conversions . . . . . . . . . . . . . . . . . . . 7

1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . . . 8

2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 Pulling out / removing the server . . . . . . . . . . . . . . . . 17

4.2 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 19

5 Main Memory . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.1 Population rules . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.2 Upgrading / replacing main memory . . . . . . . . . . . . . . 23

6 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.1 Installing a second processor . . . . . . . . . . . . . . . . . . 25

6.2 Exchanging the processor . . . . . . . . . . . . . . . . . . . 29

6.3 Exchanging the heat sink . . . . . . . . . . . . . . . . . . . . 32

7 CD/DVD Drive . . . . . . . . . . . . . . . . . . . . . . . . . 33

8 Controllers in Non-Hot-Plug PCI Slots . . . . . . . . . . . . 37

8.1 Installing controllers . . . . . . . . . . . . . . . . . . . . . . 39

9 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9.1 Closing the server . . . . . . . . . . . . . . . . . . . . . . . 41

9.2 Installing the server in the rack . . . . . . . . . . . . . . . . . 42

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

RX200 S3 OptionsGuide 5

1 Preface

The PRIMERGY RX200 S3 server is an Intel-based server for mid-size

networks and large companies. The server is suitable for use as a file server

and also as an application, information or Internet server.

1.1 Overview of the documentation

IPRIMERGY manuals are available in PDF format on the ServerBooks

CD which is supplied as part of the ServerView Suite package for every

server system.

These PDF files can also be downloaded free of charge from the

Internet: At http://manuals.fujitsu-siemens.com you will find an overview

page showing the online documentation available on the Internet. You

can go to the PRIMERGY Server documentation by clicking on industry

standard servers.

Concept and target groups

This Options Guide shows you how you can expand and upgrade the server.

VCaution!

The activities described in this manual may only be performed by

specialist personnel with technical training.

IHow to install/remove the hot-plug components is described in the

Operating Manual for the server.

Additional documentation about the server

The PRIMERGY RX200 S3 documentation comprises the following additional

manuals:

– The “Security and other important information” manual (printed copy always

supplied with the server, and available as a PDF file on the ServerBooks CD

supplied)

– The “Guarantee” manual (printed copy always supplied with the server, and

available as a PDF file on the ServerBooks CD supplied)

6 OptionsGuide RX200 S3

Overview of the documentation Preface

– The Operating Manual for PRIMERGY RX200 S3 (PDF available on the

ServerBooks CD supplied)

– The Technical Manual for the system board D2300 (PDF available on the

ServerBooks CD supplied)

– The “BIOS Setup” manual (PDF available on the ServerBooks CD supplied)

– The “Ergonomics” manual (PDF available on the ServerBooks CD supplied).

– The “ServerView Suite” manual (printed copy always supplied with the

server, and available as PDF file on the ServerBooks CD supplied)

– The “Adaptec HostRAID User’s Guide” (PDF available on the ServerBooks

CD supplied)

– The “Service Supplement for PRIMERGY RX200 S3” (PDF available on the

ServerBooks CD supplied)

IYou can order a supplementary ServerBooks CD by sending an e-mail to

the following address, quoting your server data:

Reklamat-PC-LOG@fujitsu-siemens.com

Further sources of information:

– Technical Manual on the relevant rack

– Manual on the monitor

– Manual on ServerView Server Management

– Manual on RemoteView remote server management

– Documentation on boards and drives

– Documentation on your operating system

– Information files on your operating system

(see also “Related publications” on page 49)

RX200 S3 OptionsGuide 7

Preface Extensions and conversions

1.2 Extensions and conversions

Second processor

The system board can be upgraded with a second processor. Only processors

of the same type may be used on the system board. The second processor

must have the same clock frequency as the first processor.

Extension of the main memory

The eight slots for the main memory are suitable for FBD533/PC2-4200F or

FBD667/PC2-5300F memory modules. Their organization in four memory

banks allows fast memory access with four-way interleaving.

Memory modules must always be installed in pairs. A memory bank must

always be fully equipped and with the same type of memory modules. For

further details see chapter “Main Memory” on page 21.

CD/DVD drive (option)

The PRIMERGY RX200 S3 Server is equipped with a slimline bay intended for

a CD/DVD drive (5.25 x 0.5 inch). For further details see chapter “CD/DVD

Drive” on page 33.

Additional controllers in non-hot-plug PCI slots

The system board has one PCI-X and one PCIe x8 slot. Because of the server’s

installation height, these can only be used via a riser card. Two different types

of riser card are available here:

●Type A: Two slots for PCI-X controller

Slot #1: 64 bit/100 MHz, low profile, max. length 175 mm

Slot #2: 64 bit/133 MHz, max. length 175 mm

●Type B: One slot each for a PCI-X and a PCIe controller

Slot #1: 64 bit/100 MHz, low profile, max. length 175 mm

Slot #2: PCIe x8, max. length 315 mm

IBoth slots are not hot-pluggable.

For further details see chapter “Controllers in Non-Hot-Plug PCI Slots” on

page 37.

8 OptionsGuide RX200 S3

Notational conventions Preface

Second power supply unit (option)

As an option, the power supply can be expanded with an extra power supply unit

to create a redundant power supply. If a power supply unit fails, the redundant

configuration assures continued operation. The defective power supply unit can

be replaced during operation. For information on installing the second power

supply unit please refer to the operating manual.

1.3 Notational conventions

The following notational conventions are used in this manual:

Italics indicate commands, menu items or software programs.

“Quotation marks” indicate names of chapters and terms that should be

emphasized.

Êtext which follows this symbol describes activities that

must be performed in the order shown.

VCAUTION! pay particular attention to text marked with this symbol.

Failure to observe this warning may endanger your life,

damage the server, or lead to loss of data.

Isupplementary information, remarks and tips follow this

symbol.

Table 1: Notational conventions

RX200 S3 OptionsGuide 9

2 Procedure

VCAUTION!

●The actions described in this manual should only be performed by

engineers, service personnel or technical specialists.

●Equipment repairs should only be performed by authorized, qualified

staff.

●Any failure to observe the guidelines in this manual, and any unautho-

rized openings and improper repairs could expose the user to risks

(e.g. electric shock, fire hazards) and could also damage the

equipment.

●Please note that any unauthorized opening of the device will result in

the invalidation of the warranty and exclusion from all liability.

ÊFirst of all please familiarize yourself with the safety instructions in the

chapter “Safety Instructions” on page 11ff.

ÊMake sure that all required manuals (see “Additional documentation about

the server” on page 5) are available, printing out the PDF files if necessary.

You will definitely need

– the Operating Manual for the server and

– the Service Supplement for the server

– the Technical Manual for the system board.

ÊShut down the server correctly, switch it off, pull out the power plug, and

open the server as described in the chapter “Preparation” on page 17ff.

ÊExtend or upgrade your server as described in the relevant chapter.

IHow to install/remove the hot-plug components is described in the

Operating Manual for the server.

ÊClose the server, plug all mains plugs into the power outlets, and switch on

the server as described in the chapter “Completion” on page 41ff.

ÊStart the operating system and, if necessary, configure it as required (see

the Operating Manual).

Autres manuels pour PRIMERGY RX200 S3

Table des matières

Autres manuels Fujitsu Serveur

Fujitsu

Fujitsu PRIMERGY RX600 S4 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY TX1310 M3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX1330 M1 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY TX200 S2 Manuel utilisateur

Fujitsu

Fujitsu Primergy RX100 S5 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY CX2550 M6 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX1330 M1 Manuel utilisateur

Fujitsu

Fujitsu SPARC Enterprise M3000 Manuel de service

Fujitsu

Fujitsu Primergy ECONEL 100 S2 Guide rapide

Fujitsu

Fujitsu PRIMERGY SX980 S1 Manuel du propriétaire

Fujitsu

Fujitsu PRIMERGY RX2560 M2 Manuel utilisateur

Fujitsu

Fujitsu FUTRO S450 Manuel utilisateur

Fujitsu

Fujitsu Primergy RX300 S3 Manuel du propriétaire

Fujitsu

Fujitsu PRIMERGY BX920 S2 Manuel utilisateur

Fujitsu

Fujitsu BX630 - PRIMERGY - S2 Dual Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY CX2550 M1 Manuel utilisateur

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Mode d’emploi

Fujitsu

Fujitsu SPARC Enterprise T5140 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX200 S5 Manuel utilisateur

Fujitsu

Fujitsu primergy h250 Manuel utilisateur

Fujitsu

Fujitsu Primergy RX300 S4 Manuel utilisateur

Fujitsu

Fujitsu Primergy BX920 S3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY TX120 S2 Manuel du propriétaire

Fujitsu

Fujitsu PRIMERGY TX200 S7 Guide de l'utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur