Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Guide de référence

Fujitsu SCSI Scanner Installation Procedures with VRS (GSA-1)

Windows 2000 / XP

Rev010807L Page 1 of 3

If you are installing the following model scanners with the Kofax 850S or 1700S

Adrenaline SCSI controller and a GSA-1 scanner interface card then use this document.

M4097D-VRS M4099D-VRS

Hardware requirements.

1. You will need a PC system that meets both Fujitsu’s and Kofax’s

recommended specifications

2. Kofax 850S/1700S Adrenaline controller for the M4097D/M4099D respectively.

3. Six foot (maximum) Wide SCSI 68-pin to 68-pin cable.

For recommended PC system specifications and SCSI controllers please

reference the Scanner Hardware Reference page. You may also need your

Operating System Disk.

Step A: Installing the VRS drivers.

First boot your PC and install the Kofax VRS drivers that shipped with the scanner.

The installation includes the adrenaline hardware runtime drivers. The drivers can be

down loaded from the following link Drivers and Downloads.

Special note: When installing the VRS drivers and any other software that contains

Kofax’s Image Controls pay close attention to the individual runtimes. It is strongly

recommended that you install the oldest/lower runtime application first.

Step B: Installing the Adrenaline 850S/1700S Adrenaline controller

1. Shut down your PC and remove the case cover.

2. Locate a free PCI slot and remove the back plate if necessary.

3. Install the SCSI controller in an open PCI slot. Make sure that the card is

seated completely in the slot and secured in the frame.

Warning! Failure to secure the SCSI controller in the PC can result in damage

to the SCSI card, scanner, and/or your system.

4. Boot your PC without the scanner attached and check for errors.

Step C: Unlocking the shipping lock.

If your model scanner does not have a flatbed then proceed to Step D.

The flatbed model scanners typically include a lock on the flatbed designed to

protect the scanner during shipment. Before the scanner can be used the

shipping lock must be unlocked. To unlock it do the following:

Fujitsu SCSI Scanner Installation Procedures with VRS (GSA-1)

Windows 2000 / XP

Rev010807L Page 2 of 3

The M4097D has the “L” bracket shipping lock.

1. Slide the scanner to its side as shown in figure below.

2. Unscrew the retainer screw and remove the shipping bracket.

3. Place the shipping bracket in the “use position” slot and secure it with the

retainer screw (see figure below)

4. Place scanner back in its normal position

Step D: Connecting the Scanner.

Warning! Before proceeding ensure that the power is off when connecting or

disconnecting the SCSI cable to the scanner or workstation. Failure to follow the

procedure above could result in damage to the SCSI card, scanner, and/or your system.

Termination and the SCSI ID’s for both the M4097D and M4099D VRS

scanners are handled automatically. Connect the SCSI cable to the Kofax

controller and to the Wide SCSI (68-pin) port on the scanner. Ensure all

connections are securely fastened.

Connect the power cord to the scanner and a wall outlet. Boot up the host PC

first and then turn on the scanner. Listen to and watch the back of the

Fujitsu SCSI Scanner Installation Procedures with VRS (GSA-1)

Windows 2000 / XP

Rev010807L Page 3 of 3

scanner. There are two LED’s on the grayscale adaptor (GSA) card installed in

the scanner. During scanner power up both LED’s will be on. After the first

scanner reset the green LED will turn off. Then after the second scanner reset

the yellow LED will turn off indicating that the scanner is ready and

communicating to the host PC.

Step E: Scanning with VCDEMO

1. Go to Start, Programs, Kofax VRS or Kofax Image Controls, and select

VCDEMO.EXE.

2. Next go to Source, Scanner, and click on the drop down arrow; then

select either the Fuji 4097or Fuji 4099 Virtual Rescan Source. Wait a few

seconds for the Kofax engine to load, and then place your documents in the

scanner.

3. Now go to Source, Properties and select your scanning parameters (i.e.

scan source - Flatbed or ADF, resolution, paper size).

4. Next right click on the VRS symbol in your system tray (lower right corner of

the screen) to access the VRS configuration settings.

5. Afterwards go to Source, and click on Process Image for single page scans

or Process Batch for multi-page batch scans.

Congratulations! You have successfully completed and tested your VRS scanner

installation.

Step F: Installing third party software applications.

After you have successfully installed all the Fujitsu software and hardware, then it is

time to install any additional third party scanning software that you wish to use. Please

follow the software manufacturer’s instructions for installation. Remember when

installing any software that contains Kofax’s Image Controls pay close attention to the

individual runtimes. It is strongly recommended that you install the oldest/lower

runtime application first.

Autres manuels pour M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fujitsu Scanner

Fujitsu

Fujitsu ScanSnap fi-5110EOXM Manuel utilisateur

Fujitsu

Fujitsu ScanSnap FI-4110EOX2 Manuel utilisateur

Fujitsu

Fujitsu S1500 - ScanSnap Deluxe Bundle Manuel utilisateur

Fujitsu

Fujitsu i-4990C Manuel

Fujitsu

Fujitsu fi-7800 Manuel utilisateur

Fujitsu

Fujitsu fi-5120C Manuel

Fujitsu

Fujitsu fi-8190 Manuel utilisateur

Fujitsu

Fujitsu FI-4120C Manuel utilisateur

Fujitsu

Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm... Manuel

Fujitsu

Fujitsu M3096NT Manuel utilisateur

Fujitsu

Fujitsu ScanSnap iX500 Instructions de montage

Fujitsu

Fujitsu ScanSnap iX500 Manuel utilisateur

Fujitsu

Fujitsu M3091DC Manuel utilisateur

Fujitsu

Fujitsu ScanPartner 15C Manuel d'installation et d'exploitation

Fujitsu

Fujitsu ScanSnap fi-5110EOX Manuel utilisateur

Fujitsu

Fujitsu C150-E140-03EN Manuel utilisateur

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Manuel utilisateur

Fujitsu

Fujitsu PA03630-B055 Manuel utilisateur

Fujitsu

Fujitsu M4099D Manuel utilisateur

Fujitsu

Fujitsu 5015C - fi - Sheetfed Scanner Manuel

Fujitsu

Fujitsu M3099EH Manuel

Fujitsu

Fujitsu ScanPartner 15C Guide de référence

Fujitsu

Fujitsu fi-4340C Guide de configuration

Fujitsu

Fujitsu FI-4860C2 Manuel utilisateur

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur

Innova

Innova 5210 Manuel utilisateur

Visioneer

Visioneer CardReader 100 Guide de démarrage rapide

Rohde & Schwarz

Rohde & Schwarz TSME6 Manuel utilisateur