Fujitsu Stylistic 3400 Guide de configuration rapide

FUJITSU PC CORPORATION

4/00 Pa

e 1 of 4 58-0710-00A

FMW42CR3

Wall-Mount Cradle

Assembly and Use Instructions

Stylistic 3400

The Stylistic 3400 wall-mount cradle is designed to

provide a convenient, secure, hands-free station for

your pen tablet and keyboard.

The wall-mount cradle uses high-usage DC Input

and Universal Serial Bus (USB) contact pins to

connect to the pen tablet. The USB pins are used for

interfacing with the USB keyboard. (Note that these

connectors are not visible or accessible when the

wall-mount cradle is installed.)

Assembly Instructions 0

The Stylistic 3400 wall-mount cradle is shipped

partially disassembled. Follow the instructions

below to assemble the unit. Note that these

instructions are for the assembly of the cradle, not

for mounting the cradle. The mounting and

electrical connection of the cradle are determined by

local procedures.

Parts Included 0

Verify that all parts and tools listed below are

present before proceeding with the assembly.

Table 1: Parts Included in Wall Mount Kit

Additional Parts Required 0

In order to use the wall mount cradle most

effectively, it is necessary for you to purchase the

following parts from an authorized reseller.

Quantity Part

1 Wall Mount Back Assembly

1 Wall Mount Tray Assembly

1 Cradle Assembly (plastic)

2Keys

1 Hardware Kit, consisting of:

6 Screws (short, black)

4 Screws, Phillips

(black, with star lockwasher)

2 Screws (silver)

2FlatWashers

2Ty-Wraps

Table 2: Additional Parts Required

*The "x" in the part numbers in Table 2 refers to the suffix

associated with the localized version of keyboard or AC Adapter.

Tools Required 0

The proper assembly of the wall mount cradle

requires the use of the following common tools.

Table 3: Tools Required

Installing the Cradle 0

1. Lay the wall mount back assembly on your

work surface.

2. Position the cradle assembly over the back

assembly so that the four screw holes in the

cradle align with the holes in the back assembly.

Ensure that the circuit card and cable extend

from the bottom of the cradle (reference Fig. 1).

Figure 1. Mounting the Cradle to the Back Assembly

Quantity Part

1 USB Keyboard (FMWKB5x)*

1 AC Adapter (FMWAC6x)*

Tool Description

Screwdriver Phillips

Wrench Allen, 3/32

Pliers Cutting

Circuit Card

Cradle Assembly Screws

Wall Mount Back Assembly

Standoffs

4/00 Page 2 of 4 58-0710-00A

3. Using the four black Phillips screws (with star

lockwashers), secure the cradle to the back

assembly.

4. Secure the circuit card to the two standoffs,

using the two silver screws and the two

washers, with the washers positioned between

the screws and the circuit card (reference

Figure 2).

Figure 2. Mounting the Circuit Card

Installing the keyboard 2

5. Remove the adhesive backing from the Velcro

strips that are attached to the tray.

6. Carefully position the keyboard over the strips

so that the bottom edge of the keyboard butts

against the lower lip of the tray. Once it is

positioned properly, firmly press the keyboard

onto the Velcro strips to secure it (reference

Figure 3).

Figure 3. Wall Mount Components

7. Route the coiled keyboard cable over the

vertical edge of the tray assembly. Leave

approximately ten coils on the keyboard side

(reference Figure 4)

8. Stretch the coil over the edge of the tray so the

section of cable from the edge of the tray to the

first tie point is uncoiled (reference Figure 4).

9. Tie down the cable at the first tie point using a

Ty-Wrap from the hardware kit. The tie point

is located just below the top edge of the tray

(reference Figure 3 for approximate location).

Clip any excess Ty-Wrap with the cutting

pliers.

10. Plug the keyboard plug into the jack on the

circuit card.

Figure 4. Routing the Keyboard Cable

11. Secure the remaining coil to the second

tiedown using a Ty-Wrap from the hardware

kit. Clip any excess Ty-Wrap with the cutting

pliers.

Installing the AC Adapter 4

12. Locate the Velcro strip on the right-hand side

of the tray. This is the location at which the AC

Adapter will be installed (reference Figure 5).

13. Remove the adhesive backing from the Velcro

strip on the right-hand side of the tray.

Position the AC Adapter (label side up) over

the Velcro strip with the DC power cord on the

left. Make sure the AC power cord on the right

has enough clearance that it is not tightly

crimped when routed around the adapter.

14. Secure the adapter by firmly pressing it onto

the Velcro.

15. Route the DC power cord through the

cutaway.

Circuit Card

Mounting

Hardware

Circuit Card

Cables

Back Assembly

Cradle

Tray Assembly

Velcro

Keyboard

Strips

Tiedown #1 (approximate location)

Screw Holes (6 ea.: two on

each side, two on bottom)

Coils on Keyboard

Side of Tray

(approximately ten)

Uncoiled length

Keyboard Plug

Tiedown Point #1

Tiedown Point #2

4/00 Page 3 of 4 58-0710-00A

Figure 5. AC Adapter Location

16. Route the AC power cord around the adapter,

as shown in Figure 5. Plug the AC power plug

into the circuit card, and bundle the excess

cable above the adapter.

Final Assembly 5

17. Carefully position the back assembly inside

the tray assembly so that the six holes in each

are aligned (reference Figures 3 and 6). Use

care when joining the two assemblies; ensure

that no wires or cables are crimped between

the two parts.

Figure 6. Rear of Wall Mount Assembly

Figure 7. Assembled Wall Mount

18. Using a 3/32 Allen wrench, install the six

short screws from the hardware kit. The

assembled wall mount is illustrated in Fig. 7.

19. After the wall mount cradle is assembled, it

should be mounted to a secure location and

wired to a convenient outlet in accordance

with the user’s needs. Typically, the four

hanger holes on the back of the cradle are used

to mount the cradle.

Using the Wall Mount Cradle

The contact pins in the wall mount cradle provide

DC Input and USB interfaces to the pen tablet. The

USB pins are used by the USB keyboard.

AC AdapterDC Power

Cord

Cutaway

AC Power

Plug

AC Power Cord

Assembly Screws

Hanger holes

Caution

Avoid bringing your system in direct contact with the

magnetic latches. Magnetic fields can have an

adverse affect on electronic media, and data on your

hard drive could be damaged or destroyed.

Front

Brackets

Latch

Cradle

Lock

Tray

4/00 Page 4 of 4 58-0710-00A

To install your Stylistic 3400 pen tablet in the cradle:

1. Insert the key into the cradle lock (reference

Figure 7). While pushing it firmly, turn the key

counter- clockwise to raise the latch to a 90o

angle.

2. Slide your system behind the front brackets

and into the tray. It is not necessary to use

force; the weight of the system is sufficient to

provide good contact.

3. Turn the key clockwise to lower the latch into

the locking position. Remove the key and store

in a secure location.

Figure 8. System Installed in Wall Mount

4. When not in use, lift the keyboard tray so that

the magnetic latches attach to the metal striker

plates on the front of the brackets.

Magnetic

Latches

Striker

Plates

Autres manuels pour Stylistic 3400

Ce manuel convient aux modèles suivants

Autres manuels Fujitsu Support et étagère

Fujitsu

Fujitsu PRIMERGY PG-R1CK6 Manuel utilisateur

Fujitsu

Fujitsu RC24 Manuel utilisateur

Fujitsu

Fujitsu RMK-F1 DROP-IN QRL Manuel utilisateur

Fujitsu

Fujitsu PenCentra 130 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY PG-R1CK2 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY PG-R6RC1 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY PG-R1CK7 Manuel utilisateur

Fujitsu

Fujitsu ETERNUS DX60 S2 Instructions de montage

Fujitsu

Fujitsu CMA-1U Manuel utilisateur

Fujitsu

Fujitsu CMA Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY PG-R1CK1 Manuel utilisateur

Fujitsu

Fujitsu 1740 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY 19 Manuel utilisateur

Fujitsu

Fujitsu RMK-F1 DROP-IN QRL Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY PG-R1CK20 Manuel utilisateur

Fujitsu

Fujitsu PenCentra 130 Manuel utilisateur

Fujitsu

Fujitsu PCR M2 Manuel utilisateur

Fujitsu

Fujitsu PRIMECENTER M1 Manuel utilisateur

Fujitsu

Fujitsu CMA Series Manuel utilisateur

Fujitsu

Fujitsu PRIMECENTER M1 19-inch Rack Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY PG-R1CK21 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur