Fuji Electric PXH Series Manuel utilisateur

Fuji Electric Co.,Ltd.

Temperature Controller

MODBUS SIO Driver

1 System Configuration....................................................................................................... 3

2 External Device Selection ................................................................................................ 8

3 Communication Settings .................................................................................................. 9

4 Setup Items ....................................................................................................................25

5 Cable Diagrams ............................................................................................................. 30

6 Supported Devices......................................................................................................... 71

7 Device Code and Address Code.................................................................................... 76

8 Error Messages.............................................................................................................. 77

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display and the External Device (target Temp. Controller).

In this manual, the connection procedure is described in the sections identified below:

1System Configuration

This section lists the types of External

Devices and SIO that you can connect.

)"1 System Configuration" (page 3)

2External Device Selection

Select a model (series) of the External

Device and its connection method.

)"2 External Device Selection" (page 8)

3Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

)"3 Communication Settings" (page 9)

4Setup Items

This section describes communication

setup items on the Display.

Set the Display’s communication settings

in GP Pro-EX or in off-line mode.

)"4 Setup Items" (page 25)

5Cable Diagrams

This section shows cables and adapters

for connecting the Display and the

External Device.

)"5 Cable Diagrams" (page 30)

Operation

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The following table lists system configurations for connecting Fuji Electric Co.,Ltd. External Devices and the

Display.

Series CPU Link I/F SIO Type Setting Example Cable

Diagram

PXH PXH-*1

*1 The CPU type can be connected with RS-422/485 (2 wire) when the section includes the following code:

R (RS-485)

PC Loader Port

on CPU Unit RS-232C "Setting Example 1"

(page 9)

" Cable

Diagram 1"

(page 30)

Port on CPU Unit RS-422/485

(2 wire)

"Setting Example 2"

(page 11)

" Cable

Diagram 2"

(page 32)

PXG

PXG4--*2

PXG5--*2

PXG9--*2

*2 The CPU type can be connected with RS-422/485 (2 wire) when the section includes the following codes:

M (RS-485)

V (RS-485 + Digital input (No.1))

K (RS-485 + RSV1)

J (RS-485 + CT1)

F (RS-485 + Digital input (No.1) + RSV1)

U (RS-485 + Digital input (No.1, 2, 3))

PC Loader Port

on CPU Unit RS-232C "Setting Example 3"

(page 13)

" Cable

Diagram 1"

(page 30)

Port on CPU Unit RS-422/485

(2 wire)

"Setting Example 4"

(page 15)

" Cable

Diagram 3"

(page 45)

PXR

(AutoFIX)

PXR3--*3

PXR4-*3*4*5

PXR5-*3

PXR7-*3

PXR9-*3

*3 The CPU type can be connected with RS-422/485 (2 wire) when the section includes the following codes:

M (RS-485 Modbus interface)

V (RS-485 Modbus interface + Digital input 1 point)

*4 PXR4 Socket type cannot be connected because it lacks a serial port option.

*5 CPU Unit released in July 2001 or later

Port on CPU Unit RS-422/485

(2 wire)

"Setting Example 5"

(page 17)

" Cable

Diagram 3"

(page 45)

PXR

(NoAuto-

FIX)

PXR4-*3*4*6

*6 CPU Unit released in June 2001 or earlier

Port on CPU Unit RS-422/485

(2 wire)

"Setting Example 6"

(page 19)

" Cable

Diagram 3"

(page 45)

PUM

PUMA-

PUMB-

PUME-

PUMV-

PUMN-

PUMT-

PC Loader Port

on CPU Unit RS-232C "Setting Example 7"

(page 21)

" Cable

Diagram 1"

(page 30)

Port on CPU Unit RS-422/485

(2 wire)

"Setting Example 8"

(page 23)

" Cable

Diagram 4"

(page 58)

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 4

Connection Configuration

• 1:1 Connection

• 1:n Connection

Display External Device

Display

External Device External Device External Device

Maximum number of External Devices: 16

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 5

IPC COM Port

When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please

refer to the IPC manual for details.

Usable port

Series

Usable Port

RS-232C RS-422/485(4 wire) RS-422/485(2 wire)

PS-2000B COM1*1 , COM2,

COM3*1, COM4

*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.

PS-3450A, PS-3451A,

PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2

PS-3650A (T41 model),

PS-3651A (T41 model) COM1*1 --

PS-3650A (T42 model),

PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2

PS-3700A (Pentium®4-M)

PS-3710A

COM1*1, COM2*1,

COM3*2 , COM4

*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.

COM3*2 COM3*2

PS-3711A COM1*1, COM2*2 COM2*2 COM2*2

PS4000*3

*3 When making communication between an External Device and COM port on the Expansion slot,

only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the

specification of COM port.

For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.

Please refer to the IPC manual for details of pin layout.

COM1, COM2 - -

PL3000 COM1*1*2, COM2*1,

COM3, COM4 COM1*1*2 COM1*1*2

PE-4000B Atom N270 COM1, COM2 - -

PE-4000B Atom N2600 COM1, COM2 COM3*4 , COM4*4,

COM5*4, COM6*4

*4 Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.

COM3*4, COM4*4,

COM5*4, COM6*4

PS5000 (Slim Panel Type

Core i3 Model) *5 *6 COM1, COM2*4 COM2*4 COM2*4

PS5000 (Slim Panel Type

Atom Model)

*5 *6

COM1, COM2*7 COM2*7 COM2*7

PS5000 (Enclosed Panel

Type)*8 COM1 - -

PS5000 (Modular Type

PFXPU/PFXPP)*5 *6

PS5000 (Modular Type

PFXPL2B5-6)

COM1*7 COM1*7 COM1*7

PS5000 (Modular Type

PFXPL2B1-4) COM1, COM2*7 COM2*7 COM2*7

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 6

DIP Switch settings (PL3000 / PS3000 Series)

RS-232C

*5 When setting up communication between an External Device and the RS-232C/422/485 interface

module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using

PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+

and 8.CTS+, and connect 6.RTS- and 9.CTS-.

When using RS-422/485 communication with External Devices, you may need to reduce the

transmission speed and increase the TX Wait time.

*6 To use RS-422/485 communication on the RS-232C/422/485 interface module, the DIP Switch

setting is required. Please refer to "Knowledge Base" (FAQs) on the support site. (http://www.pro-

face.com/trans/en/manual/1001.html)

*7 Set up the SIO type with the DIP Switch. Please refer to the IPC manual for details of DIP Switch.

The BOX Atom has not a switch to set the RS-232C, RS-422/485 mode. Use the BIOS for the

setting.

*8 For the connection with the External Device, on the user-created cable read as if the connector on

the Display-side is a M12 A-coding 8 pin socket. The pin assignment is the same as described in

the cable diagram. For the M12 A-coding connector, use PFXZPSCNM122.

DIP Switch Setting Description

1OFF

*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.

Reserved (always OFF)

2OFF

SIO type: RS-232C

3OFF

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

Settings FAQ ID

PFXZPBMPR42P2, RS422/485 change method FA263858

PFXZPBMPR42P2 termination resistor setting FA263974

PFXZPBMPR44P2, RS422/485 change method FA264087

PFXZPBMPR44P2 termination resistor setting FA264088

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 7

RS-422/485 (4 wire)

RS-422/485 (2 wire)

DIP Switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

DIP Switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available

8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available

9ON

RS (RTS) Auto control mode: Enabled

10 ON

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 8

2 External Device Selection

Select the External Device to be connected to the Display.

Setup Items Setup Description

Number of Devices/PLCs Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the

display.

Manufacturer Select the manufacturer of the External Device to connect. Select "Fuji Electric

Co.,Ltd.".

Series

Select the External Device model (series) and the connection method. Select "Temp.

Controller MODBUS SIO".

In System configuration, make sure the External Device you are connecting is

supported by "Temp. Controller MODBUS SIO".

)"1 System Configuration" (page 3)

Port Select the Display port to be connected to the External Device.

Use System Area Not available for this driver.

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 9

3 Communication Settings

This section provides examples of communication settings recommended by Pro-face for the Display and the

External Device.

3.1 Setting Example 1

GP-Pro EX Settings

Communication Settings

To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

Device Setting

To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]

window, select the external device and click [Settings] .

To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add

Device] to add another External Device.

Temperature Controller MODBUS SIO Driver

GP-Pro EX Device/PLC Connection Manual 10

External Device Settings

For External Device communication settings, use the SEL key, UP key, DOWN key, Digit selection key, or DISP

key located in the operation area on the front of the controller.

Refer to your External Device manual for details.

1Press SEL key.

2Press UP key or DOWN key to display [COM].

3Press SEL key.

4Press UP key or DOWN key to display the setting parameter.

5Press SEL key to switch to setting mode.

6Press UP key, DOWN key or Digit selection key to display the setting value.

7Press SEL key.

8Press DISP key twice.

9Reboot the External Device.

Setting Value

Setting Parameter Setting Value Setup Description

SPD2 384 RS-232C communication speed

BIT2 8o RS-232C bit format

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fuji Electric Régulateurs de température

Fuji Electric

Fuji Electric PXR3 Series Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Fuji Electric

Fuji Electric Micro-Controller X Socket type Manuel utilisateur

Fuji Electric

Fuji Electric PXZ Series Manuel utilisateur

Fuji Electric

Fuji Electric PXR3 Series Manuel utilisateur

Fuji Electric

Fuji Electric PUMCE Manuel utilisateur

Fuji Electric

Fuji Electric PUM Series Manuel utilisateur

Fuji Electric

Fuji Electric PXF4 Manuel utilisateur

Fuji Electric

Fuji Electric PXG5 Manuel utilisateur

Fuji Electric

Fuji Electric PUMCL Manuel utilisateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Manuel utilisateur