FS S1900-24T Manuel utilisateur
S1900-24T
V1.0
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
ETHERNET UNMANAGED SWITCH
UNMANAGED ETHERNET-SWITCH
SWITCH ETHERNET NON GÉRÉ
V1.0
Quick Start Guide
Quick-Start Anleitung
Guide de Démarrage Rapide
Introduction
Accessories
Thank you for choosing S1900-24T switch. This guide is designed to familiarize you with the layout of
the switch and describes how to deploy the switch in your network.
S1900-24T
Power Cord x 1Rubber Pad x 4
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423161521
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
Screw x 6
（KM3*8mm）
Front Panel Ports
Hardware Overview
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423161521
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
RJ45
Mounting Bracket x 2
EN
1
Back Panel
Grounding Point
AC 100-240V 50/60Hz
Power Supply
Front Panel LEDs
RJ45 10/100/1000BASE-T ports for Ethernet connection. Port 15 to 16
can be used for uplink ports (VLAN on).
Ports Description
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423161521
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
RJ45
PWR
LEDs
PWR
Status Description
On
Off
Solid on
RJ45
Off
The switch is powered on properly.
The switch is not powered on, or not powered
on properly.
The port is connected to a device, but no data is
being transmitted over the port.
The port is not connected or is not connected
properly.
Blinking The port is connected to a device and data is
being transmitted over the port.
EN
2
Installation Requirements
Before you begin the installation, make sure that you have the following:
Desktop mounting: ESD bracelet (or ESD gloves).
Wall mounting: ESD bracelet (or ESD gloves), ladder, marker, hammer drill, rubber hammer,
screwdriver.
Rack mounting: ESD bracelet (or ESD gloves), Phillips screwdriver, M6 Screws, Standard-sized 19"
wide rack with a minimum of 1U height available.
The installation site must be well ventilated. Ensure that there is adequate air flow around
the switch.
Site Environment:
Do not operate it in an area that exceeds an ambient temperature of 45°C.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
EN
3
S1900-24T
43 65 87 109 121 1 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
Mounting the Switch
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
Wall Mounting
1. Rotate the two L-shaped brackets by 90 degrees and fix them to both sides of the switch with
the included screws.
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
EN
4
S1900-24T
43
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
2. Horizontally place the switch onto the wall with its RJ45 ports facing upward. Then mark the
screw holes with the marker.
3. Drill holes in the marked positions, and then knock the expansion bolts (self-prepared,
M5*40 mm) into the holes.
4. Insert the screws (self-prepared, PA5*25 mm, head diameter: 10 mm) through the holes of the
two L-shaped brackets, and secure the screws into the expansion bolts with a screwdriver. Ensure
that the switch is installed firmly with its RJ45 ports facing upward.
NOTE: This switch can only be installed on a concrete or non-flammable wall.
EN
5
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
4 65 87 109 1211 1413 1817 2019 2221 2423
1615
24
Rack Mounting
1.Secure the mounting brackets to the two sides of the switch with six KM3*8 screws.
2. Attach the switch to the rack using the screws and tighten it.
EN
6
AC 100-240V 50/60Hz
AC 100-240V 50/60Hz
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the back of the switch with the washer and
screws.
Grounding the Switch
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
Connecting the Power
WARNING: Do not install power cable while the power is on.
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
EN
7
S1900-24T
43 65 87 109 1211 1413 1817 2019 2221 2423
1615
21
1 5 9 13 17 21
2 6 10 14 18 22
3 7 11 15 19 23
4PWR 8 12 16 20 24
AC 100-240V 50/60Hz
Connecting the RJ45 Ports
1. Connect an Ethernet cable to the RJ45 port of a computer, printer, network storage, or other
network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
EN
8
Support and Other Resources
Download
Help Center
Contact Us
https://www.fs.com/download.html
https://www.fs.com/service/help_center.html
https://www.fs.com/contact_us.html
Product Warranty
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a
free return within 30 Days from the day you receive your goods. This excludes any custom made
items or tailored solutions.
Warranty: S1900-24T Switch enjoys 2 year limited warranty against defect in materials
or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html
2
EN
9
Table des matières
Langues :
Autres manuels FS Changer
FS
FS S5800-48F4SR Manuel utilisateur
FS
FS IES3110 Series Manuel utilisateur
FS
FS S5500-48T8SP Manuel utilisateur
FS
FS S3910 Series Manuel utilisateur
FS
FS S1900-5T Manuel utilisateur
FS
FS S3900 Series Manuel utilisateur
FS
FS PoE+ Series Manuel utilisateur
FS
FS S3150-8T2FP Manuel utilisateur
FS
FS PoE+ Series Manuel utilisateur
FS
FS STP Series Manuel utilisateur
FS
FS S5860-20SQ Manuel utilisateur
FS
FS N Series Manuel utilisateur
FS
FS IES5100-24TF Manuel utilisateur
FS
FS S5810 Series Manuel d'utilisation
FS
FS Fiberstore S8050-20Q4C Manuel utilisateur
FS
FS S3150-8T2FP Manuel utilisateur
FS
FS S1900-8TP Manuel utilisateur
FS
FS S5500-48T8SP Manuel utilisateur
FS
FS S3700-24T4F Mode d’emploi
FS
FS S3150-8T2FP Manuel utilisateur
