Frigidaire GAM155Q1A - GIBSON 15100BTU 115V 12.5A 10.3 SPD 4 WAY AIR... Manuel utilisateur

Please read ALL instructions before installing. Two people are

recommended to install this product. If a new electrical outlet

is required, have the outlet installed by a qualified electrician

before installing unit. See#5 in Preliminary Instructions

following.

Do the following before starting to install unit. See illustrations

below.

1. Check window opening size - the mounting parts furnished

with this air conditioner are made to install in a wooden

sill double-hung window. The standard parts are for

window dimensions listed above. Open sash to a minimum

2. Check condition of window - all wood parts of window

must be in good shape and able to firmly hold the needed

screws. If not, make repairs before installing unit.

3. Check your storm windows - if your storm window

frame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG. 2, or by removing

storm window while room air conditioner is being installed.

(continued)

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

BOARD THICKNESS AS

REQUIRED, ALONG

ENTIRE STOOL. FASTEN

WITH TWO NAILS OR

SCREWS.

FIG. 1

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

P/N 220219A032

SAFETY LOCK AND

3/4'' LONG HEX HEAD

SCREW

Installation Instructions

For Heavy Duty (FAS Models) and

Median (FAM Models) Air Conditioners

Preliminary Instructions

of 19''(483mm). (FIG. 1)

Check dimensions of your unit to determine model type:

Heavy duty (FAS) Median (FAM)

Unit Height: 18 5/8” 17 5/8”

Unit Width: 26 ½” 23 ½”

Min. Window Opening: 19” 18 ½”

Min. Window Width: 31” 26 ½”

Max. Window Width: 43” 40 ½”

4. CHECK FOR ANYTHING THAT COULD BLOCK

AIRFLOW - check area outside of window for things

such as shrubs, trees, or awnings. Inside, be sure

furniture, drapes, or blinds will not stop proper airflow.

5. Check the available electrical service - power supply must

be the same as that shown on the unit serial nameplate.

(See Owner’s Guide for serial plate location.) Power cord

is 48''long. Be sure you have an outlet near.

All models have a 3-prong service plug to provide proper

service and safe positive grouding. Do not change plug in

any way. Do not use an adapter plug. If your present wall

outlet does not match your plug, call a qualified electrician

to make the needed change.

6. Carefully unpack air conditioner - remove all packing

material. Protect floor or carpet from damage. Two

people should be used to move and install unit.

Tools Required

a large flat blade screwdriver

tape measure

adjustable wrench or pliers

pencil

Level

Socket wrenches

Phillips screwdriver

Hardware (in plastic bag)

Qty.

4ea.

2ea.

Washer Head

Locking Screw

For window panels

3/4'' Long Hex-

Head Screw

Safety Lock

1/2'' Long Screw

and Locknut

3/4'' Long Flat

Head Bolt and

Locknut

Sill Angle Bracket

Long hex-head

locking screw for

top angle, side

retainer 5/16''

Long

Avoid fire hazard or electric

shock. Do not use an extension cord or an

adaptor plug. Do not remove any prong from

the power cord.

Grounding type wall

receptacle

Do not, under any

circumstances, cut,

remove, or bypass the

grounding prong.

Power supply cord

with 3-prong grounding

plug and current

detection device

2. Install top

angle and

side retainers

to cabinet as

shown in FIG. 6.

1. Place cabinet on floor, a bench, or a table.

2. Slide ''I'' section of window filler panel into side retainer

on the side of the cabinet (see Figures 7-8). Do both

sides.

FIG. 6

5/16'' Long

HEX HEAD

PLASTIC

FRAME

WINDOW FILLER

PA NE L

SIDE

RETAINER

FIG. 7

FIG. 8

TOP

VIEW

AIR CONDITIONER

CABINET PLASTIC

FRAME

LOCKING

SCREW

HOLE

WINDOW

FILLER

PANEL

''I'' SECTION

Window Mounting

Remove Chassis

Assemble Window

Filler Panels

1. Attach foam gasket to top angle above holes as

shown in FIG. 6.

2Install Top Angle

and Side Bracket

1. Pull down front panel and remove filter. (See FIG. 1).

2. Lift front upwards and place to one side.

3. Locate the four front screws and remove. These screws will

be needed to re-install the front later. (See FIG. 2).

4. Pry away front from cabinet sides as per photo (See FIG. 3).

5. Gently lift front off unit and place to one side (See FIG. 4).

6. Remove shipping crews from top of unit and also on the side

by the base if installed.

7. Hold the cabinet while pulling on the base handle, and care-

fully remove the unit.

8. Add two foam inserts to holes in top of cabinet where

shipping screws were removed from.

9. Your unit may come with internal packaging. THIS

PACKAGING MUST BE REMOVED PRIOR TO

INSTALLING THE AIR CONDITIONER BACK

INTO THE CABINET. (See FIG. 5).

FIG. 1

FIG. 3 FIG. 4

FIG. 5

Internal Packaging

FIG. 2

Place Cabinet in

Window

1. Open window and mark

center of window stool.

2. Place cabinet in window with bottom stool angle firmly

seated over window stool as shown. Bring window

down temporarily behind top angle to hold cabinet in

place.

3. Shift cabinet left or right as needed to line up center of

cabinet on center line marked on stool.

4. Fasten cabinet to window stool with 2 screws into

holes.(You may wish to pre-drill pilot holes.)

5. Add bottom rail seal over screws to window stool.





Bottom

Rail Seal

3/4''LONG HEX-

HEAD SCREW

STOOL

ANGLE

Install Support

Bracket

1. Hold each support bracket flush against outside of sill,

and tight to bottom of cabinet as shown below. Mark

brackets at top level of sill, and remove.

2. Assemble sill angle bracket to support brackets at the

marked position, as shown. Hand tighten, but allow

for any changes later.

3. Install support brackets (with sill angle brackets

attached) to correct hole in bottom of cabinet as shown.

4. Tighten all 6 bolts securely.

MARK

LEFT

LOCKNUT

SILL ANGLE

BRACKET

FLAT HEAD BOLT

2 EACH REQ’D FOR EACH

SUPPORT BRACKET

RIGHT

1/2'' LONG SCREWS

AND LOCKNUTS

1/2''long screws

and locknuts

3. Insert top and bottom legs of window filler panel frame

into channel in the top angle and bottom rail. Do both

sides.

4. Insert washer head locking screws (2) into holes in

top leg of f iller panel frame (see Step 6). Do not totally

tighten. Allow leg to slide freely. Screws will be

tightened after Section 6.

1. Carefully raise window to expose filler panel locking

screws. Loosen screws so filler panels slide easily.

2. Extend panels to fill window opening completely.

Tighten locking screws on top.

3. Close window behind top angle.

1. Trim sash seal to fit window width. Insert into space

between upper and lower sashes.

2. Attach right angle safety lock as shown.

LOCKING SCREWS

WINDOW SASH SEAL

SAFETY LOCK

3/4''long hex-

head screw

Extend Window Filler

6Panels

and Sash Seal

Install Window Lock

Install Chassis into

Cabinet and Install

Front to Unit

3. Be sure chassis is firmly seated towards rear of cabinet.

Installation of front is the reverse of removal outlined

in Section 1.

2. DO not push on controls OR finned coils.

!CAUTION

Lift air conditioner and carefully slide into cabinet

leaving 6” protruding.

Carefully measure and cut an opening with the following

dimensions depending on your model. See FIGS. 1 and 2.

4. Build a wooden frame with the INSIDE dimensions of

Frame depth should be the same as wall thickness. Fill in

the space from the opening to the studs with wood spacers,

as shown.

5. Nail frame to spacers to spacers with front flush with

drywall.

NAIL SPACERS TO STUDS

LEVEL

NOTE: Consult local building codes prior to installation,

or a qualified carpenter.

This air conditioner has a slide-out chassis, so that it can be

NOTE: All parts need for Thru-The-Wall Installation are

provided, except a wood frame, shims, and 10 wood screws (#

10-1'' long minimum). Select a wall surface that:

1. does not support major structural loads such as the frame

construction at ends of windows, and under truss-bearing

points, etc.

2. does not have plumbing or wiring inside.

3. is near existing electrical outlets, or where another outlet

can be installed.

4. faces, and is not blocked to the area to be cooled.

5. allows unblocked airflow from rear sides and end (outside)

of installed air conditioner.

1. Prepare wall in frame construction (including brick and

stucco veneer). Working from inside the room, find wall

stud nearest the center of area where air conditioner will

be installed (by sounding wall, or by magnetically finding

nails).

2. Cut or knock out a hole on each side of center stud.

3. Measure between inside edges of every other stud as shown

in FIG. 1.

FIG. 1

3-3/8'' MIN

(8.6 cm)

FIG. 2

Inside

Frame

Height

UP TO

8-1/2''

Thru-The-Wall Installation

Select Wall Location

Prepare Wall

Heavy Duty (FAS) Median (FAM)

Max wall thickness 12'' 10''

IMPORTANT: Side louvers must never be blocked.

installed through an outside wall as specified below: Heavy Duty (FAS) Median (FAM)

Inside Frame Height: 187/8'' (47.9cm) 18'' (45.7cm)

Inside Frame Width: 263/4'' (67.9cm) 237/8'' (60.6cm)

your model listed above.(Measure twice remember...)

Inside

Frame

Width

WIDTH “X” = inside model width plus twice the thickness

of framing material used.

HEIGHT “Y” = inside model height plus twice the thickness

of framing material used.

NOTE: If wall thickness is 8-1/2'' or more, add aluminum

flashing over bottom of frame opening to assure no water can

enter area between inner and outer wall.

1. Slide chassis from cabinet. Refer back to Step 1 of

Window Mounting.

2. Place cabinet into opening with bottom rail resting firmly

on bottom board of wooden frame.

3. Position cabinet to achieve proper slope for water removal.

(See FIG. 1 below.)

4. Secure bottom rail to wood frame with two large wood

screws 1''(2.5 cm) long using the two holes in the bottom

of the channel resting on frame. (See FIG. 2 following)

1'' LONG

WOOD SCREW

FIG. 2

Refer to Step 4 of Window Mounting for assembly of support

brackets. A wooden strip nailed to the outside wall should be

used in conjunction with sill support angle brackets.

5. Screw or nail cabinet wooden frame using shims if frame

is oversized, to eliminate distortion. Remember to maintain

proper slope as described in Step 3.

6. Install chassis into cabinet by following all steps in Step

8 of Window Mounting. (continued)

Support brakcet

Wooden strip

CAULK AS

REQUIRED

ALUMINUM FLASHING

OVER BOTTOM OF FRAME

OVER

81/2''

3/4'' PLUS

TRIM THICKNESS

SEE PARA 5

5/16''

3/8''

LEVEL

FIG. 1

Prepare and Install

Cabinet

OPTIONAL: Caulking and installation of trim on interior wall

may be done. You can buy wood from your local lumber or

hardware supply. On the outside, caulk openings around top

and sides of cabinet, and all sides of wood sleeve to the opening.

NOTE: See Step 7, Item 3 of Window Mounting Instructions

for bottom rail seal location.

Masonry Construction

1. Cut or build a wall opening in the masonry wall similar

to the frame construction (refer to Step 2 of Thru-the-

Wall Installation for a wall thickness greater than 8-1/

2'').

2. Secure cabinet in place using masonry nails, or the right

masonry anchor screws. (Another way to do this is to build

an in-between frame of 2x4’s as shown in the Step 2 Prepare

Wall illustrations-but make it double framed on either

side, and install between masonry wall opening and cabinet.

Frame must be securely anchored to masonry wall

opening) This way gives very good louver clearance on

either side of cabinet.

3. Install a lintel to support masonry wall above cabinet.

Existing holes in cabinet can be used and/or additional

holes can be drilled to fasten cabinet at various positions.

Be sure that side louver clearance is in accordance with

Step1above.

4. Install exterior cabient support brackets as shown in

Step 2 of Thru-the-Wall Installation. Caulk or flash if

neede, to provide a wether-tight seal around top and

sides of cabinet.

5. To complete installation, apply wood trim molding

around room side projection of cabinet.

Table des matières

Autres manuels Frigidaire Climatiseur

Frigidaire

Frigidaire CRA09EPT115 Manuel du propriétaire

Frigidaire

Frigidaire 220204d031 Manuel utilisateur

Frigidaire

Frigidaire LRA257ST217 Manuel du propriétaire

Frigidaire

Frigidaire FFRE0833S1 Manuel utilisateur

Frigidaire

Frigidaire FRA053XT71 Manuel du propriétaire

Frigidaire

Frigidaire Room Air Conditioner Manuel du propriétaire

Frigidaire

Frigidaire FAA087S7AF Manuel utilisateur

Frigidaire

Frigidaire Room Air Conditioner Manuel utilisateur

Frigidaire

Frigidaire FAH08EP1T Manuel utilisateur

Frigidaire

Frigidaire FFRA0522Q14 Manuel du propriétaire

Frigidaire

Frigidaire CRA084KT710 Manuel utilisateur

Frigidaire

Frigidaire FRS123LS1 Manuel du propriétaire

Frigidaire

Frigidaire LRA257ST216 Manuel utilisateur

Frigidaire

Frigidaire FAC084N7A Manuel utilisateur

Frigidaire

Frigidaire FGRC084WA1 Manuel du propriétaire

Frigidaire

Frigidaire LRA067AT7 Manuel du propriétaire

Frigidaire

Frigidaire FAC066L7A1 Manuel utilisateur

Frigidaire

Frigidaire FFRE0533Q1 Manuel utilisateur

Frigidaire

Frigidaire FAA051N7A2 Manuel utilisateur

Frigidaire

Frigidaire FRA122CV1 Manuel utilisateur

Frigidaire

Frigidaire FRA084KT71 Manuel du propriétaire

Frigidaire

Frigidaire EC300W-FA Manuel utilisateur

Frigidaire

Frigidaire FAS224J2A2 Manuel utilisateur

Frigidaire

Frigidaire FAS185M2A2 Manuel utilisateur

Manuels Climatiseur populaires d'autres marques

Spheros

Spheros CC 355 Manuel utilisateur

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuel utilisateur

Panasonic

Panasonic CS-E12HKEW Manuel utilisateur

nedis

nedis ACMB1WT7 Manuel utilisateur

Samsung

Samsung AR KV Series Mode d’emploi

Daikin

Daikin FCFV50A Manuel utilisateur

Fujitsu

Fujitsu Inverter ASBA30JFC Manuel utilisateur

Toshiba

Toshiba RAS-M10SMUV-E Manuel utilisateur

Daikin

Daikin FXLQ20MAVE Manuel utilisateur

Hitachi

Hitachi RAS-E24CAK Manuel utilisateur

CIAT

CIAT Magister 2 Series Mode d’emploi

Bestron

Bestron AAC6000 Manuel utilisateur

Hisense

Hisense 7K Manuel technique

Samsung

Samsung AS09HM3N Manuel utilisateur

Soleus Air

Soleus Air GB-PAC-08E4 Manuel utilisateur

McQuay

McQuay MCK020A Manuel utilisateur

Webasto

Webasto Frigo Top 25 DS Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manuel utilisateur