Fox Electronics GSM525S SMS BLUE Manuel utilisateur

This manual will explain the command structure and all commands

that are valid for the SMS communicator.

SMS COMMAND FORMAT

Please note: ALL commands are CASE-SENSITIVE.

The Commands below illustrate the Instruction Format.

.Command Data #[ ][Space][ ][ ]

.A +27425874585#

.Command Data Extended Data #[ ][Space][ ][Space][ ][ ]

.A +27425874585 10101010#

Multiple .A Commands can also be issued in a single SMS by

replacing the . with a star * character for consecutive instructions. ( ) ( )

.Command Data *Command Data #[ ][Space][ ][Space][ ][ ][Space][ ][ ]

.A +27415875874 *A +276589745858#

For commands where TEXT is entered, a single apostrophe (’) at

the beginning and a single apostrophe at the end is used.

.Command ’Text Data’#[ ][Space][ ][ ]

.ADR ‘no123, Peter Drive, Durban’#

.IH2 ‘medical emergency’#

GSM525S SMS BLUE

8 Input 5 Output Communicator

Installer Command Manual

STANDARD COMMANDS

F Adding Master User .M1

FAdding Numbers .A

FDelete Numbers .D

FDelete Own Number .DN

FRequest Stored Numbers .N?

FSetting Auto Test interval .AT

FGlobal Settings 1 .G1

FGlobal Settings 2 .G2

FGlobal Settings 3 .G3

FGlobal Settings 4 .G4

FRequest Health Status .H

FGate Re-Trigger Time .GRT

FActivating Outputs .OP1-5

FRenaming Address Text .ADR

F Renaming Input High/Low Text .I1L

FRemove SIM Card .RS

F Select SIM Slot 1 .SM1

F Select SIM Slot 2 .SM2

F Output Pulse Settings .PO1

FSetting AC Fail/AC Restore Time .ACT

FAdding third party Master .AM

FAdding Administrator .AA

FAdding Access .AAC

FSetting Unit Defaults .DF

FMaster Resetting Unit .MR

FMaster Reset and Default .MRD

FAIR time request Setup .AS

FRemaining AIR time request .AIR

FAirtime low level Reminder setup .AR

FInternational number prefix set .INT

FBase Station Add .BA

FBase Station Delete .BD

PWR

PGM

SIM

SIM 2

SIM

SIM 1

INPUT INPUT

1 2 3 4 5 6 7 CID ACM

POS NEG

12V DC

16 V

1000uF

NO NC

RL2

NO NC

RL1

OUTPUT RELAY 2 RELAY 1

5 4 3 NO/C COM NO/C COM

SIGNAL

STAT

FOX

GSM52S

FOX

ELECTRONICS

(PTY)

LTD

CMD Description Syntax/Example Access

.A Adding User

Phone Numbers

.A Cell No #[space][ ]

.A +27802345678#

-MASTER User

-ADMIN User

.A Adding User Phone

Numbers-With Settings.

.A Cell No Settings Byte[space][ ][space][ ][space]

[ ]Output #

.A +27802345678 10101010 r1#

-MASTER User

-ADMIN User

.A Adding User Phone

Numbers-With Settings

& Validity Period.

.A Cell No Settings Byte[space][ [space][ [space]

[ ][space][ ]Output Validity Period #

.A +27802345678 10101010 r1 d7#

.A +27802345678 10101010 r2 n2#

-MASTER User

-ADMIN User

ADDING NUMBERS WITH SETTINGS

Customised, user-specific settings can be set by adding additional setup data to the SMS when adding a number.

.A +27802345678 b1,b2,b3...b8 r1 #[space] ][space][ [ ]

ADDING NUMBERS USING A VALIDITY PERIOD.

Users are added with a Validity Period that will determine the duration of their access to the communicator before

being automatically erased. The validity period is entered with (number of activations) or (number of days)n d

the access will be allowed. The maximum number entry allowed is 250.

Multiple numbers may be added using a single SMS by replacing the . with a * for the consecutive commands.

.A +27802345678 *A +27808765432 11111000 r2 d1#

.M1 Adding Master User

Number-This Command

will set the sending Cell

Number as the Master User.

.M1#

-MASTER User

-Any Phone

Number

Notes: Master and Admin Users have access to Program The GSM52S SMS Communicator.

Receiving of replies for Status and Setup Commands can be selected by setting bits 2&3

of G2 Global Setting.

The Master User’s number must also be added to receive activations.

.D Deleting Phone

Numbers.

.D Cell No #[space][ ]

.D +27802345678#

-MASTER User

-ADMIN User

.N? Request User

Numbers? in memory.

This will return a list of the

numbers currently stored on

the unit.

.N?# -MASTER User

-ADMIN User

.AT Set Auto-Test Interval.

[Hours]

.AT Auto Test Interval hours #[space][ ]

.AT 24#

Default = 0 hours(Test Disabled)

(Max. = 250 hours)

-MASTER User

-ADMIN User

Fox Electronics (Pty) Ltd

Deleting YOUR OWN

Phone Number.

.DN Cell No #[space][ ]

.DN +27802345678# -Valid USER

SMS 8 Input 5 Output Blue

Output

OutPut 4

Call-In activates

OutPut 1 - Relay 1

OutPut 2 - Relay 2

OutPut 3

Not used

OutPut 5

Not used

USER FUNCTION BITS

BIT 1

BIT 2

BIT 3

BIT 4

BIT 5

BIT 6

BIT 7

BIT 8

SETTING - APPLIES TO INPUT/OUTPUT OF GSM525

Send Emergency(Input 1) to Number

Send Burglary(Input 2) to Number

Send Lock/Open(Input 3) to Number

Send AC Fail/Restore(ACM) to Number

Send Telemetry 01(Input 4) to Number

Send Telemetry 02(Input 5) to Number

Send Telemetry 03(Input 6) to Number

Send Telemetry 04(Input 7) to Number

.DN

CMD Description Syntax/Example Access

.G1 Global Settings 1.

The text can be ALL

used when all of the

BITS must be set to 1's.

This will Enable Call-in Mode,

make call-in Secure,

OP1 and OP2 a Pulsed

Output.

.G1 Config Byte #[space][ ]

.G1 11111111# -MASTER User

-ADMIN User

BIT1

BIT2

BIT3

BIT4

BIT5

BIT6

BIT7

BIT8

.G2 Global Settings 2.

The text can be ALL

used when all of the

BITS must be set to 1's

NOTE: When the Serial

port is enabled Contact

ID input is disabled.

.G2 Config Byte #[space][ ]

.G2 11111111#

.G2 ALL#

-MASTER User

-ADMIN User

BIT1

BIT2

BIT3

BIT4

BIT5

BIT6

BIT7

BIT8

BIT2-If ‘0’, the Communicator will send Replies

for ALL Commands to Master and Admin Users.

BIT3-If ‘0’, the Communicator will send Status

messages to Master and Admin Users.

Call-In Mode*- This mode allows a selected

output(OP1 - OP5) to activated when the

specified user calls the Communicator.

Secure Caller** - Makes sure the caller who

accesses the system is a valid user before

activating the output. NOTE: If not secure

the output to be activated will be only OP1.

Output Re-Trigger*** - If this setting is enabled,

the output that was activated using the call-in

feature will be re-triggered after the time selected

using the ‘. ’ command(OP1 & OP2 ONLY).GRT

.G3 Global Settings 3.

Selectable

Auto-Generated

message settings.

This command allows

status report filtering.

.G3 Config Byte #[space][ ]

.G3 11111111#

.G3 ALL#

-MASTER User

-ADMIN User

BIT DEFINITION G3

BIT1-Send “Power Up”?

BIT2-Send “AC Fail/Restore”?

BIT3-Send “Signal Low”?

BIT4-Send “Battery Low/Restore”?

BIT5-Send “SIM Slot Change”?

BIT6-Reserved

BIT7-Reserved

BIT8-Reserved

1/0 Description

1=Yes

1=N/A

0=No

0=N/A

1=N/A 0=N/A

BIT1

BIT2

BIT3

BIT4

BIT5

BIT6

BIT7

BIT8

If you do NOT wish to receive the messages as

in the above table, set the individual bit to ‘0’ .

Fox Electronics (Pty) Ltd

BIT DEFINITION G1

BIT1-Call-in Mode*

BIT2-Secure Caller** Mode

BIT4-OP1 Action

BIT5-OP2 Action

BIT3-Output Re-Trigger***

BIT6-OP3 Action

BIT7-OP4 Action

BIT8-OP5 Action

1/0 Description

1=Enabled

1=Secure

1=Pulsed

1=Trigger once

0=Disabled

0=Open

0=Latched

0=Output Re-Trigger

0=Latched

1=Pulsed

BIT DEFINITION G2

BIT1-Serial Port Mode

BIT2-Send Command Replies to:

BIT3-Send Status SMS’s to:

BIT4-Reserved

BIT5-Texecom Serial EVENTS?

BIT6-Texe Serial Report ARMING?

BIT7-Texe Serial Report Restorals?

BIT8-Texe Serial Report Bypass?

1/0 Description

1=Enabled

1=Commanding User

1=Master ONLY

1=N/A

1=LIMITED

1=No

0=Disabled

0=All ADMINS + Master

0=N/A

0=ALL

0=Yes

1=No 0=Yes

SMS 8 Input 5 Output Blue

BIT DEFINITION G2

BIT1-Serial Port Mode

BIT2-Send Command Replies to:

BIT3-Send Status SMSes to:

BIT4-Reserved

BIT5-Texecom Serial EVENTS?

BIT6-Texe Ser Report ARMING?

BIT7-Texe Ser Report Restorals?

BIT8-Texe Ser Report Bypass?

1/0 Description

1=Enabled

1=Commanding User

1=Master ONLY

1=N/A

1=LIMITED

1=No

0=Disabled

0=All ADMINS + Master

0=N/A

0=ALL

0=Yes

1=No 0=Yes

CMD Description Syntax/Example Access

.H Request Health Status

of Communicator.

.H#

The Health Status SMS is sent as follows:

-MASTER User

-ADMIN User

Activating Outputs

1,2,3,4 & 5 via SMS

Command.

Activates the selected output

as per it’s preset Pulse Time,

Pulsed or Latched setting.

.OP1#

.OP2#

.OP3#

.OP4#

.OP5#

-MASTER User

-ADMIN User

-Valid User

.OP1

.OP5

.ADR Set Address Text.

This instruction updates the

Text added into the SMS

when reporting events.

.ADR ’Address Text’ #[space][ ]

.ADR ‘123 Earth Street,

Milky Way, the Cosmos.’#

Maximum characters = 40.Do not use * in text. ( )

-MASTER User

-ADMIN Use

Status Report-

Batt:13.8v..............

Sig:57%................

IP1:H.....................

IP2:L......................

IP3:H.....................

IP4:L.....................

IP5:L......................

IP6:H.....................

IP7:L.....................

OP1:L....................

OP2:H...................

OP3:L....................

OP4:L....................

OP5:L....................

AC Pwr: ON*.........

SIM1......................

V:xxxxx..................

Current DC Voltage

RSSI Signal Level

Input 1 State(High/Low)

Input 2 State(High/Low)

Input 3 State(High/Low)

Input 4 State(High/Low)

Input 5 State(High/Low)

Input 6 State(High/Low)

Input 7 State(High/Low)

Output 1 State(High/Low)

Output 2 State(High/Low)

Output 3 State(High/Low)

Output 4 State(High/Low)

Output 5 State(High/Low)

AC Power(ON*/OFF)

Active SIM Card(1 or 2)

Version Number.

Fox Electronics (Pty) Ltd

Set Gate Re-Trigger Time.

Sets the time after which the

activated Output is

re-triggered(If Enabled in G1).

[Seconds]

.GRT .GRT[space][Time delay (sec)]#

.GRT 20#

If G1-BIT5 = 0, then output will be Re-Triggered

after 20 seconds. (Max. = 250s, Min. = 1s.)

-MASTER User

-ADMIN User

BIT DEFINITION G4

BIT1- Input 1 (EMERGENCY)

BIT2- Input 2 (BURGLARY)

BIT3- Input 3 (LOCK/OPEN)

BIT4- Input 4 (Telemetry 1)

BIT8-Restoral Report Input1,2&4-7

1/0 Description

1=Positive Trig

1=Enabled

0=Negative Trig

0=Disabled

BIT5- Input 5 (Telemetry 2)

BIT5- Input 6 (Telemetry 3)

BIT7- Input 7 (Telemetry 4)

1=Positive Trig

0=Negative Trig

Global Settings 4.

When Base Station Monitoring

is setup the input BITS must

be set to determine the trigger

polarity that is reported to the

Base station.

-MASTER User

-ADMIN User

With BIT8 enabled, Input 1,2 & 4,5,6,7 will also

send an Input Restore signal.

.G5 Global Settings 5.

For Future use

-MASTER User

-ADMIN User

SMS 8 Input 5 Output Blue

.G4

CMD Description Syntax/Example Access

.RS Remove SIM card in

secure mode Makes

active SIM PIN ‘0000’.

.RS# -MASTER User

-ADMIN User

Select SIM Slot 1 or 2.

Makes one selected SIM slot

active.

.SM1#

.SM2# -MASTER User

-ADMIN User

.PO1

.PO2

.PO3

.PO4

.PO5

Set Pulse time of

Outputs 1,2,3,4,5.

Setup how long OP1 to OP5

is pulsed on for in Seconds.

Default is 2s. Range 1-250s

. Pulse Time(seconds) #[Output][space][ ]

.PO1 5#

.PO2 010#

-MASTER User

-ADMIN User

.ACT Set AC Power

Fail/Restore Time Delay

in Minutes.

Default is 15m. Range 1-250m

.ACT Delay time #[space][ ]

.ACT 15#

-MASTER User

-ADMIN User

.AA Adding Admin

Phone Numbers

When a number is added as

ADMIN, the user will also be

able to execute programming

commands.

.AA Cell No #[space][ ]

.AA +27802345678#

-MASTER User

-ADMIN User

Fox Electronics (Pty) Ltd

-ANY NUMBER

Add Master user from

a 3rd party phone. The

unit will allow access to

programming for 30

minutes in this mode.

.AM Cell No #[space][ ]

.AM +27802345678#

Set Input Trigger Lables

for Inputs 1,2 & 4,5,6,7

High(12v) or Low(0v)

states.

Configuring the output labels

will determine if the input will

react to a Positive, Negative

or both activations.

To clear a specific label just

leave a space after the

command followed by #.

FACTORY INPUT LABELS

Input 1 - Emergency

Input 2 - Burglary

Input 3 - Lock / Open

Input 4 - Telemetry 1

Input 5 - Telemetry 2

Input 6 - Telemetry 3

Input 7 - Telemetry 4

Input 8 - ACM AC Restore/Fail

is NOT programmable.

. ’Input Label’ #[Input level][space][ ]

.I1H ‘Pump On’#

.I1L #

Input 1 - Positive Trip Labeled ‘Pump On’.

.I2H #

.I2L ‘Box Tamper’#

Input 2 - Negative Trip,

Labeled ‘Box Tamper’.

.I3H ‘Alarm Activated’#

.I3L ‘Alarm Deactivated’#

Input 3

HIGH state Labeled ‘Alarm Activated’

LOW state Labeled ‘Alarm Deactivated’.

-MASTER User

-ADMIN User

SMS 8 Input 5 Output Blue

.I1H

.I1L

.I2H

.I2L

.I3H

.I3L

.I4H

.I4L

.I5H

.I5L

.I6H

.I6L

.I7H

.I7L

.AM

.Sm1

.Sm2

CMD Description Syntax/Example Access

.DF Set unit Defaults.

This will reset all Global G1-3

, Pulse timers, Auto Test and

AC Fail/Restore times to

Defaults.

.DF# -MASTER User

-ADMIN User

.MR# -MASTER User

-ADMIN User

Master Reset unit.

This command will only

Remove the Master

User. All existing users and

settings will remain.

-MASTER User

-ADMIN User

Master Reset & Default.

This command will reset all

unit timers to defaults and

delete all Users.

.MRD#

Fox Electronics (Pty) Ltd

AIR time remaining on

active SIM card

.AIR

This will return a message :

Your remaining airtime R230.80

-MASTER User

-ADMIN User

Airtime Setup

This Instruction is used

to setup the airtime

retrieval from the

cell network.

.AS ’Airtime ’ # [space][ ][space][ ]Charactors

request code up to currency indicator

incl. spaces(2 digits)

.AS ‘*100#’ 17# VODACOM

.AS ‘*141#’ 01# MTN

.AS ‘*101#’ 20# CELL C

-MASTER User

-ADMIN User

.AA Adding Admin

Phone Numbers

-With Settings.

.AA Cell No Settings Byte #[space][ ][space][ ]

.AA +27802345678 10101010#

-MASTER User

-ADMIN User

.AA Adding Admin

Phone Numbers

-With Settings

& Validity Period.

.AA Cell No Settings Byte[space][ [space][ [space]

[ ]Validity Period #

.AA +27802345678 10101010 d7#

.AA +27802345678 10101010 n2#

-MASTER User

-ADMIN User

Adding ACcess

Phone Numbers

When a number is added as

ACCESS, the user’s usage

will be reported to Master/

Admin Users.

.AAC Cell No #[space][ ]

.AAC +27802345678#

NOTE: User access notification will be

sent to Master and or Admin Users,

depending on global ‘G2’ programming.

-MASTER User

-ADMIN User

.AAC Adding ACess

Phone Numbers

-With Settings.

.AAC Cell No Settings Byte[space][ ][space][ ][space]

[ ]Output #

.AAC +27802345678 10101010#

-MASTER User

-ADMIN User

Adding ACess

Phone Numbers

-With Settings

& Validity Period.

.A Cell No Settings ByteAC[space][ [space][ [space]

[ ][space][ ]Output Validity Period #

.AAC +27802345678 10101010 r1 d7#

.AAC +27802345678 10101010 r2 n2#

-MASTER User

-ADMIN User

.AAC

SMS 8 Input 5 Output Blue

.AAC

.MR

.MRD

.AS

.AIR

CMD Description Syntax/Example Access

Fox Electronics (Pty) Ltd

.INT INTernational number

prefix programming.

Default +27.

.INT ’+International prefix’ # [space][ ]

.INT ‘+254’#

This will set the International call prefix to

+254. This setting is required to ensure all

features operate correctly.

-MASTER User

-ADMIN User

.AR Air time Reminder

setup. When the Air

Time available on the

SIM reaches this level

an Airtime LOW signal

is sent to the users.

.AR[space][Minimum value (2 digits)]#

.AR 20#

This instruction will set the minimum reminder

value to R20 and will return a message :

Airtime Reminder set at R20

-MASTER User

-ADMIN User

.AR

SMS 8 Input 5 Output Blue

-MASTER User

-ADMIN User

.BA

.BD

Base Station number

Add. Add number of the

base station monitoring

the unit.

(Monitoring Enabled)

Excluding Texecom

serial.

.BA Cell No ID Code number #[space][ ][space][ ][space][ ]

.BA +27802345678 12 1234#

This command will add the Base station

cell number with the System ID and Unit

Code Number that is reported to the

monitoring software.

Base Station numbers

Delete. Delete the Base

Station monitoring

numbers from the unit.

(Monitoring Disabled)

.BD#

This command will Delete ALL the Base

station numbers (all 4) from the unit,

disabling monitoring to a Base station and

Monitoring software.

-MASTER User

-ADMIN User

-MASTER User

-ADMIN User

.BA1

.BA2

.BA3

Base Station number

Add1,2,3. Add number

of the additional 3 base

stations monitoring

the unit.

(Monitoring Enabled)

.BA Cell No #[space][ ]

.BA +27802345678#

This command will add up to 3 additional

Base stations cell numbers to the unit that

it will report activations to. The code number

that is reported to the monitoring software

remains the same as setup with .BA#.

Autres manuels Fox Electronics Téléphone portable

Fox Electronics

Fox Electronics GSM52S Manuel utilisateur

Manuels Téléphone portable populaires d'autres marques

Zte

Zte BLADE A520 Manuel utilisateur

Nokia

Nokia Lumia 620 Manuel utilisateur

Blackbe;rry

Blackbe;rry KEYone Manuel utilisateur

Bea-fon

Bea-fon X5 Premium Manuel utilisateur

Blackbe;rry

Blackbe;rry 8707 Series Manuel utilisateur

Blackbe;rry

Blackbe;rry Storm Mode d'emploi

LG LM-X420QN Manuel utilisateur

LifeWatch

LifeWatch V Manuel utilisateur

Bea-fon

Bea-fon SILVER LINE SL860 Manuel utilisateur

IKI Mobile

IKI Mobile KF4.5i Manuel utilisateur

Hitech

Hitech HT-850 Manuel utilisateur

Yezz

Yezz Fashion F10 Manuel utilisateur

Point Mobile

Point Mobile PM60 Manuel utilisateur

Blackbe;rry

Blackbe;rry Q10 Manuel utilisateur

Blackbe;rry

Blackbe;rry Bold 9900 Manuel utilisateur

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuel utilisateur

LG LM-K420EMW Manuel utilisateur

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuel utilisateur