Fostex FD-8 Manuel utilisateur

FD-8 Owner’s Manual Supplement

<NOTE>: When formatting a large capacity hard disk, the time required to format will be in

relation to disk size. As a general estimate, it requires about 15 minutes to format 1GB and

thus, as an example, it will take about 7 hours for a 30GB hard disk.

The functions explained here have been added to the FD-8 subsequent to version

1.10 because of a version up of the software. Prior to operating the FD-8, please

read this supplement together with the main manual.

1. Large capacity hard disks can now be used.

It is now possible to use a 2.5 inch E-IDE hard disk with a capacity up to about 30GB

(FS=44.1kHz) for the FD-8 internal current drive disk.

2. In the BAR/BEAT/CLK (bar/beat/clock) time base, the offset figure of the BAR

that indicates the head of the disk can now be edited.

Although [Time Base] is explained in [Before Operating] in the main owners manual, for

the unit representing the present traveling position of the FD-8, MTC (MIDI time code) or

BAR/BEAT/CLK are employed in addition to ABS (absolute time). For this reason, the

figure indicating the present disk position will be different depending on the selected

time base.

With the FD-8 in the initial setup state, when the disk is at the head position (ABS 00M

00S 00F) the MTC offset indication will be [MTC 00H 59M 57S 00F], and when by BAR/

BEAT/CLK it will be [-002BAR 1BEAT 00CLK].

Before this version up, changing the offset figure was limited to MTC and the BAR/BEAT/

CLK offset figure was fixed to [-002BAR 1BEAT 00CLK]. But after this version up, the BAR

offset figure of BAR/BEAT/CLK can now be changed and set to any figure within a range

of -002 ~ -009.

The FD-8’s initial state [-002BAR 1BEAT 00CLK] will always be displayed and the BAR

offset figure will be [-002BAR].

In order to set the offset figure of the BAR/BEAT/CLK display, use the SETUP mode of the

FD-8 in the same manner for setup of MTC offset. For procedures, refer to the reverse

side explanation. For setup of MTC offset, please refer to [SETUP mode] of the main

owners manual.

1. Preselect the program to which offset is to be setup.

The following example shows in the display that

program 2 have been selected.

2. Switch to the SETUP mode by pressing the SETUP

key.

In the initial setup, the [Sign. Set?] menu will be

displayed (If a different menu is displayed, rotate the

JOG dial to display the [Sign. Set?] menu.).

3. Then press the EXECUTE/YES key.

The display will change to [Sign. Chk] and the

presently set beat will be shown. In the initial setup,

the display will show that the first bar is set to 4/4

beat.

4. Rotate the JOG dial counter-clockwise.

The offset figure of the presently set bar is displayed

and in the initial setup, [-002BAR OFFSET] will be

displayed as shown below.

5. Press the EXECUTE/YES key.

Simultaneous with entering [Sign. Edit] mode, [2] of

-002BAR will blink and the BAR offset figure can then

be editied.

6. Enter the desired offset figure by rotating the JOG

dial, and then press the EXECUTE/YES key.

Any offset figure in the range of 2~9 can be input

(Example below show that [5] had been entered for

the BAR figure.). When the EXECUTE/YES key is

pressed after input of the above number, the offset

figure thus input will be setup and the display will

change to the [Sign. Set?] menu.

7. Exit from the SETUP mode by pressing the EXIT/NO

key.

Setup procedures for BAR/BEAT/CLK offset

<NOTE>: Offset setups can be executed for each program. The setup content will be

maintained even though power is switched off.

FOSTEX CORPORATION

3-2-35, Musashino, Akishima-shi,Tokyo 196-0021, Japan

FOSTEX CORPORATION OF AMERICA

15431, Blackburn Ave., Norwalk, CA 90650, U.S.A.

Blink

PRINTED IN JAPAN AUG.1999 8288 677 000 FX.

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SETUP

BAR

44.1kHz

EXECUTE

/YES

EXECUTE

/YES

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SETUP

BAR

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

BAR

44.1kHz

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SETUP

BAR

44.1kHz

EXECUTE

/YES

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

BAR

44.1kHz

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SMF

PGM

ABS

44.1kHz

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SMF

PGM

ABS

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

44.1kHz

SETUP

Autres manuels pour FD-8

Table des matières

Autres manuels Fostex Équipement d'enregistrement

Fostex

Fostex D-90 Manuel utilisateur

Fostex

Fostex VF-160 Manuel utilisateur

Fostex

Fostex DV-824 Guide de configuration

Fostex

Fostex 8335 Manuel utilisateur

Fostex

Fostex D-30 Manuel utilisateur

Fostex

Fostex R8 Manuel utilisateur

Fostex

Fostex 4010 Manuel utilisateur

Fostex

Fostex FR-2 Manuel technique

Fostex

Fostex LIVE RECORDING MIXER LR16 Manuel utilisateur

Fostex

Fostex CR200 Manuel utilisateur

Fostex

Fostex 8330 Manuel utilisateur

Fostex

Fostex D-108 Manuel utilisateur

Fostex

Fostex X-28H Manuel utilisateur

Fostex

Fostex DE-10 Manuel utilisateur

Fostex

Fostex FD-8 Manuel utilisateur

Fostex

Fostex VR800Z Manuel utilisateur

Fostex

Fostex VR800 Manuel utilisateur

Fostex

Fostex X-14 Manuel utilisateur

Fostex

Fostex DMT-8 Manuel utilisateur

Fostex

Fostex FD-8 Guide de l'utilisateur

Fostex

Fostex CR500 Manuel utilisateur

Fostex

Fostex D2424LVmk2 Manuel utilisateur

Fostex

Fostex CR200 Manuel utilisateur

Fostex

Fostex D-90 Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien