FMS F-15 Manuel utilisateur

64MM F-15 V2
SIMPLE RIGID
Easy assembly STRONG DURABLE EPO
STABLE
SMOOTH FLYING PERFORMANCE
FMSMODEL.COM


As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and
others or result in damage to the product or the property of others. This model is controlled by a radio signal subject
to interference from many sources outside your control. This interference can cause momentary loss of control so it
is advisable to always keep a safe distance in all directions around your model, as this margin will help avoid collisions
or injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
·Never operate your model with low transmitter batteries.
·Always operate your model in an open area away from cars, traffic or people.
·Avoid operating your model in the street where injury or damage can occur.
·Never operate the model in populated areas for any reason.
·Carefully follow the directions and warnings for this and any optional support equipment you use (chargers,
rechargeable battery packs, etc.)
·Keep all chemicals, small parts and anything electrical out of the reach of children.
·Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and
protected for this purpose.
·Never lick or place any part of your model in your mouth as it could cause serious injury or even death.
Lithium Polymer (Li-Po) Battery Warning
CAUTION: Always follow the manufacturer’s instructions for safe use and disposal of batteries. Fire, property
damage, or serious injury can result from the mishandling of Li-Po batteries.
By handling, charging or using a Li-Po Battery you assume all risks associated with lithium batteries.
If at any time the batteries begin to swell or balloon, discontinue use immediately!
Always store the batteries at room temperature in a dry area to extend the life of the battery. Always transport
or temporarily store the battery at a temperature range of 40-120F. Do not store the battery or model in a car or in direct
sunlight. If stored in a hot car, the battery can be damaged or even catch fire.
Never use a Ni-Mh Charger to charge Li-Po Batteries. Failure to charge the battery with a Li-Po compatible charger
may cause fire resulting in personal injury and property damage.
Never discharge Li-Po Cells below 3V.
Never leave charging batteries unattended.
Never charge damaged batteries.
Use a battery charger that is designed to safely charge the Li-Po Battery. Read the charger instructions carefully
before use. When charging the battery, make certain the battery is on a heat resistant surface. It is also highly
recommended to place the Li-Po Battery inside a fire resistant charging bag readily available at hobby shops or
online.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious
injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure
to do so could result in injury or damage to the product or other property. This product is not intended for use by
children without direct adult supervision.
This manual contains instructions for safety operation and maintenance. It is essential to read and follow all the
instructions and warnings in the manual prior to assembly, setup or use, in order to operate and avoid damage or
serious injury.

Introduction
Contents of Kit
Model Assembly
Important ESC and model information
Get your model ready to fly
The transmitter and model setup
Check the control throws
Clevis Installation
Control Horn and Servo Arm Settings
Center of Gravity(CG)
Before flying the model
Flying Course
Troubleshooting
Spare parts list content
ESC instruction
Table of Contents
Introduction
3
····························································································································3
························································································································4
······················································································································5
·························································································9
·····································································································10
······························································································10
········································································································11
··················································································································12
·························································································12
·············································································································13
············································································································14
·······················································································································15
····················································································································16
···········································································································17
·····················································································································18
FMS is pleased to announce that all 64mm ducted fan aircrafts are being upgraded. Beginning with the release
of the 64mm F-15 V2. Inspired by the superior features of the original model, version two (V2) has improved
mechanical and structural features that will enhance air performance and decrease assembly time.
The fiber pipe greatly enhances the wing strength for enhanced flying maneuvers. Improved main wing set and
landing gear installation optimizes strength of structure and reduces assembly time.
The latest 64mm ducted fan can achieve more than 800 grams of thrust.
The differences in speeds between the V1 and V2 will be noticeable. If you possess the “need for speed,”
accessories such as missiles can be removed to create a faster more streamlined model.
Upgrades
420mm fiber pipe inserted through the fuselage and main wing
Use of four inner-hexagon screws instead of glue improves main wing set and landing gear installation
optimizing strength of structure
New more powerful 64mm 11-blade ducted fan with up to 800 grams of thrust.
New 2840-KV3150 motor
New Predator 40A ESC
The latest FMS EPO foam material creates stronger, more impact-resistant planes.
Environmentally friendly water-based paint minimizes blistering from sun
Pre-installed newly designed control horns allows more throw
Features
420mm fiber pipe inserted through the fuselage and main wing
Improved main wing set and landing gear installation optimizes strength of structure and reduces
assembly time
64mm 11-blade ducted fan
2840-KV3150 motor
Predator 40A ESC
5x 9g servos
The latest EPO foam material creating a stronger, more impact-resistant plane
Environmentally friendly water-based paint minimizes blistering from sun
Pre-installed newly designed control horns allows more throw

A.
B.
C. D.
F. G.
E.
H.
I. J.
A: Fuselage
B: Main wing (Left and Right)
C: Vertical Stabilizer (Left and Right)
D: Horizontal Stabilizer (Left and Right)
E: Missile Set
F: Nose Cone
G: Canopy
H: Fiber Pipe
I: Linkage and Screws
(4-HKM3.0*10, 4-KA2.0*8)
J: Landing Gear Set
Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and
labels. If any parts are missing or defective, please indentify the name or part number (refer to the spare
Contents of Kit
4
Wingspan: 715mm (28.1in)
Overall Length: 980mm (38.6in)
Flying Weight: Around 1025g (36.2 oz)
Motor Size: Brushless 2840-KV3150
Wing Load: 66.5g/dm² (0.15oz/in²)
Wing Area: 15.4dm² (238.7sq.in)
ESC: 40A
Servo: 9g Servo x 5

fig1
fig2
5
1.Slide the wing tube into the fuselage (fig1).
2.Install the left and right wing over the wing tube and into the wing slot of the fuselage (fig1).
3.Secure the left and right wing to the fuselage using the 4 screws included (fig2)
Main Wing Installation
Model Assembly
HKM3.0*10

fig4
fig3
6
Vertical Stabilizer Installation:
Horizontal Stabilizer Installation:
Model Assembly
Required Adhesives:
Foam Safe Medium CA
Carefully apply CA to the base and the side of the rear fuselage slot. Install the stabilizer into place.
Ensure the control horn faces down as shown (fig3).
Note: Ensure the stabilizer horizontal axis is parallel to the wing. Adjust any misalignment before the glue
dries thoroughly.
Carefully apply CA to the top rear fuselage slots. Install the vertical stabilizer into place (fig4).

7
1. Install the main landing gear with the included screws (fig6).
2. Install the front landing gear and then tighten the screw (fig7).
Landing Gear Installation:
Model Assembly
KA2.0*8
Install the clevis. (fig5) Refer to the Clevis Installation on page 12.
Clevis Installation:
fig6 fig7
fig5

8
1. Apply glue on the missile with CA and slide the whole missile set into the rails on each wing (fig8/fig9).
Apply the nose cone to the front fuselage as diagram shows. Ensure the nose cone is on the correct
side.(fig10)
Missile Installation:
Nose Cone Installation:
Model Assembly
Required Adhesives:
Foam Safe Medium CA
fig10
fig8
fig9

9
3. Check the connection diagram below for more information (fig12.)
Battery and radio installation
fig12
1. Apply the hook tape to the cable end of the battery (fig 11).
2. Slide the battery into the battery compartment with the power supply cable toward the fore-end
of the plane.
Note: you may need to relocate the battery position to achieve the correct CG for your model.
fig11
Table des matières
Autres manuels FMS Aéronef


















