FS-WTM01
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
Wireless trainer unit
认证相关 Certications
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FS-WTM01] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.ysky-cn.com.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons
is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal eort, you contribute to recycle
valuable raw materials and the treatment of toxic substances.
FCC ID: N4ZWTM0100
本说明书中的图片和插图仅供参考，可能与实际产品外观有所不同。 产品设计和规格可能会有所更改，恕不另行通知。
Figures and illustrations in this manual are provided for reference only and may dier from actual product appearance. Product design and specicatiions may be changed without notice.
Manufacturer：ShenZhen FLYSKY Technology Co., Ltd
Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China
注意事项：
• 使用前必须确保本模块安装正确，否则可能导致设备严重损坏。
• 关闭时，请务必先关闭本模块电源，然后关闭遥控器。否则将有可能导致遥控设备失控或者引擎继续工作而引发事故。
• 确保本模块安装在远离电机或电子噪声过多的区域。
• 本模块天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保本模块和导电材料之间至少有 1 厘米以上的距离。
• 准备过程中，请勿接通本模块电源，避免造成不必要的损失。
• 为了防止短路，请注意所有的正负极连接正确。
• 在使用过程中，请避免用力拉扯此线材，以免造成线材损坏影响正常使用。
• 此线缆仅用于 RC 模型，不要在其他地方时使用。
Attentio:
• Make sure the unit is installed correctly, failure to do so may result in serious injury.
• Make sure the unit is powered o before turning o the transmitter, failure to do so may lead to unintended operation or loss of control.
• Make sure the unot is mounted away from motors or any device that emits excessive electrical noise.
• Keep the antenna of the unit at least 1cm away from conductive materials such as carbon or metal.
• Do not power on the receiver during the setup process to prevent loss of control.
• To prevent short circuit, please make sure that all the anode and cathode are connected correctly.
• Do not pull hard the wire during use to avoid causing damage to the wire, thus aecting its normal use.
• The cable are used for only the RC model and shall not be used for other purposes.
兼容性 Compatibility
本无线教练模块兼容：AFHDS 2A/AFHDS 3 协议发射机（如 PL18 等）。可兼容教练接口为 Futaba 接口、S 端子接口或 3.5mm 音频输出接口且支持标准 PPM 信
号的发射机作为教练机。
The wireless trainer unit is compatible with the transmitters with AFHDS 2A/AFHDS 3 protocol, such as PL18 and etc, it can also be compatible with the
transmitter which is set as a trainer transmitter, and this transmitter should has Futaba interface, S terminal connector or 3.5 mm Audio head, as well as
should support standard PPM signal.
固件更新 Firmware update
本无线教练模块固件更新需通过富斯遥控管家（FlySkyAssistant）完成（仅 3.0 及以上版本支持，富斯遥控管家固件可从官网 www.ysky-cn.com 获取）。
可通过以下两种方式进入更新：
1. 先将发射机与本无线教练模块对码后（LED 灯常亮），再将发射机与电脑连接，然后在电脑端打开富斯遥控管家，通过富斯遥控管家进行固件更新；
2. 先将发射机与电脑连接，再将无线教练模块的三档开关拨至 UPD 位置，之后接通无线教练模块电源，无线教练模块即进入强制更新状态（LED 灯三闪一灭），
然后在电脑端打开富斯遥控管家，通过富斯遥控管家进行固件更新。
注：PL18 发射机固件版本需 1.0.55 及以上版本可与本无线教练模块对码。
The rmware of this wireless trainer unit is updated through the FlyskyAssistant (Only version 3.0 or above is supported. The rmware of FlyskyAssistant is
available on the Flysky ocial website).
It can be updated through the following two ways:
1. After the binding between the transmitter and the wireless trainer unit (the LED is solid on), connect the transmitter to the computer, then open the
FlyskyAssistant on the computer to update the rmware.
2. Connect the transmitter to the computer rst, then toggle the three-level switch (AFHDS 2A/AFHDS3/UPD) to UPD position, afterwards power on the
wireless trainer unit. The wireless trainer unit will enter the forced update state (the LED operates in three-ash-one-o manner repeatedly ). Open the
FlyskyAssistant on the computer to update the rmware.
Note:PL18Transmitterwiththermwareversion1.0.55orabovecanbindwiththiswirelesstrainerunit.
