Fluke T5-600 Manuel utilisateur
®
T5-600 / T5-1000
Electrical Tester
Instruction Sheet
W
Read First: Safety Information
Use the tester only as specified in this Instruction Sheet,
otherwise the protection provided by the tester may be
impaired.
WWarning
•Do not use the tester if it is damaged or operating
abnormally. Protection may be impaired.
•Before each use:
Make sure the battery door is closed and latched.
Inspect the tester and test leads. Look for cracks,
missing plastic, exposed metal, or damaged
insulation. Replace damaged test leads before using
the tester.
Verify the tester’s operation by measuring a known
voltage.
Perform the Battery Test to avoid false readings due
to a low battery.
•Replace the batteries as soon as the low battery
indicator (M) appears.
•Do not use the tester around explosive gas, vapor or
dust.
•Do not apply more than the rated voltage, as marked on
the tester, between terminals or between any terminal
and earth ground.
•When servicing the tester, use only specified
replacement parts.
•Use caution when working above 30 V ac rms, 42 V ac
peak, or 60 V dc.
•When using the probes, keep your fingers behind the
finger guards on the probes.
•Connect the common test lead before you connect the
live test lead. Disconnect the live test lead first.
Symbols
BAC (alternating current) JEarth ground
FDC (direct current) TDouble insulated
WSafety Information
(Refer to the manual) MBattery
Voltage Indicator
While the tester is on, the LED glows when more than 30 V ac or
60 V dc is present across the leads.
The LED can also glow at lower voltages. Be aware that such
voltages pose a shock hazard.
PN 688374 (English) July 1997, Rev. 1, 9/98
© 1997-1998 Fluke Corporation, All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
Measuring Voltage
(V)
The tester automatically selects dc (DC) or ac (AC) voltage mode
based on the peak values of the measured signal.
The tester defaults to ac voltage when turned on.
DC Voltage
T5-600 maximum: 600 V
T5-1000 maximum: 1000 V
CAT III
AC Voltage
45 Hz to 66 Hz
T5-600 maximum: 600 V rms
T5-1000 maximum: 1000 V rms
CAT III
DC
AC
V
AC/DC
Automatic
Selection
V
AC/DC
Automatic
Selection
ex2.eps
Measuring Continuity and Resistance
(Ω)
Continuity Resistance
1000 Ω
Range
Greater than
400 Ω
Open Short
Less than
25 Ω
ex3.eps
Beeper indicates shorts lasting 1 ms (1/1000 second) or longer.
Measuring AC Current
(A)
0.5"(12.9 mm)
maximum
A
AC
ex1.eps
•Range: 0 A to 100.0 A;
45 Hz to 66 Hz
•Remove probes from test
points.
•Place conductor anywhere
within the sensor zone
(shaded area shown below).
OKOK
OK OK
Sensor
Zone
ex5.eps
Display Hold
To hold the reading on the display, press and release HOLD.
The voltage indicator LED ( ) continues to operate.
To exit the display hold mode, press and release HOLD again, or
turn the rotary switch to a new position.
Automatic Power Down
The tester turns off automatically if you do not turn the rotary
switch or press HOLD for approximately 34 minutes. To resume
operation, turn the tester off, wait two seconds, then turn the
tester on.
Low Battery Indicator
WWarning
To avoid false readings, which could lead to
possible electric shock or personal injury, replace
the battery as soon as the low battery indicator
(M)appears.
Maintenance
Clean the case with a damp cloth and detergent. Do not use
abrasives or solvents.
Because the inputs are electronically protected, no fuses are
required.
Battery Replacement
Observe the polarity markings inside the battery compartment.
+
+
Do not
overtighten screw
Disconnect probes
from Voltage
Switch OFF
2 AA
+
+
ex4.eps
Replacement Parts
Test Lead Assembly.
Replace only with Fluke double-insulated leads
( T)See "Accessories" for available probes.
PN 648029
Battery Door PN 648144
Battery Door Screw PN 643830
Accessories
H5 Belt Holster
TP1 Probe Set, Flat-Blade
TP4 Probe Set, 4 mm round
Service Information Sheet
, PN 686953
To contact Fluke, call:
USA and Canada: 1-888-99-FLUKE (1-888-993-5853)
Europe: +31 402-678-200
Japan: +81-3-3434-0181
Singapore: +65-276- 6196
Anywhere in the world: +1-425-446-5500
Visit Fluke’s Web site at www.fluke.com.
Specifications
Calibration: One-year calibration cycle.
Maximum Voltage Between any Terminal and Earth Ground:
T5-600: 600 V rms, Overvoltage Category III;
T5-1000: 1000 V rms, Overvoltage Category III
Temperature: Operating: -10 °C to +50 °C (14 °F to 122 °F);
Storage: -30 °C to +60 °C (-22 °F to +140 °F)
Altitude: Operating: 2000 m (6562 ft); Storage: 10,000 m
(32808 ft)
Relative Humidity: 0 % to 95 %, 5 °C to 30 °C (41 °F to 86 °F);
0 % to 75 %, 30 °C to 40 °C (86 °F to 104 °F);
0 % to 45 %, 40 °C to 50 °C (104 °F to 122 °F)
Battery Type and Life: AA (2); 400 hours continuous with
alkaline; 200 hours continuous with zinc chloride
Shock, Vibration: 1 m drop at 15 °C to 35 °C (59 °F to 95 °F)
per ANSI/ISA-S82.01-1994 and EN 61010-1: 1993. Sinusoidal
vibration per MIL-PRF-28800F for a Class 2 instrument
(5 Hz to 55 Hz, 3 g maximum).
Surge Protection: T5-600 6 kV per IEC 1010-1, 1990-09;
T5-1000 8 kV per IEC 1010-1, 1990-09
Enclosure Rating: IP 52 per IEC 529, no vacuum applied
RF Field Specification: 0.5 % full scale + (specified accuracy)
at 3 V / m; Amps: >100 MHz, performance unspecified.
Safety: Complies with ANSI/ISA-S82.01-94 for use in
Overvoltage category III (CAT III) locations, UL3111, CSA/CAN
C22.2 No.1010.1-92, and EN61010-1: 1993.
EMC: EN 50081-1, EN 50082-1
Certifications:
Accuracy is specified for 1 year after calibration, at 18 °C to 28
°C (64 °F to 82 °F) with relative humidity to 90 %. AC
conversions are ac-coupled, average responding, and calibrated
to the rms value of a sine wave input.
Accuracy specifications are given as follows:
±( [ % of reading] + [number of least significant digits] )
Temperature coefficient of 0.1 x (specified accuracy) / °C for
<18 °C or >28 °C (< 64.4 °F or > 82.4 °F)
Function T5-600
Range T5-1000
Range Resolution Accuracy
K600 V rms 1000 V rms 1 V ±(1.5 % + 2 digits)
L600 V 1000 V 1 V ±(1 % + 1 digit)
?100.0 A 100.0 A 0.1 A ±(3 % + 3 digits)
e1000 Ω1000 Ω1 Ω±(1 % + 2 digits)
Input Protection
Function Input Impedance
(nominal) T5-600 T5-1000
K1 MΩ, <100 pF ac-coupled 600 V rms 1000 V rms
L1 MΩ, <100 pF 600 V rms 1000 V rms
e>2.6 kΩ600 V rms 1000 V rms
Function Open Circuit Test Voltage Short Circuit Current
e2.4 V dc (nominal) <600 µA
Limited Warranty & Limitation Of Liability
This Fluke product will be free from defects in material and
workmanship for two years from the date of purchase. This warranty
does not cover fuses, disposable batteries, or damage from accident,
neglect, misuse or abnormal conditions of operation or handling.
Resellers are not authorized to extend any other warranty on Fluke’s
behalf. To obtain service during the warranty period, send the
defective product to the nearest Fluke Authorized Service Center with
a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY
CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
Fluke Corporation Fluke Europe B.V.
P.O. Box 9090 PO Box 1186
Everett WA 98206-9090 5602 B.D. Eindhoven
USA The Netherlands
10/96
Autres manuels pour T5-600
5
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fluke Équipement de test
Fluke
Fluke DTX Series Manuel utilisateur
Fluke
Fluke SimpliFiber Pro Manuel utilisateur
Fluke
Fluke SHAFTALIGN touch Guide de configuration
Fluke
Fluke ScopeMeter 190-502 Manuel d'instructions
Fluke
Fluke 9011 Manuel utilisateur
Fluke
Fluke TS 44 PRO Manuel de la liste des pièces
Fluke
Fluke 729 Pro Manuel utilisateur
Fluke
Fluke 717 1G Manuel utilisateur
Fluke
Fluke Series II Manuel utilisateur
Fluke
Fluke 5700A Series II Service Manuel utilisateur
Fluke
Fluke 719PRO Manuel utilisateur
Fluke
Fluke 525A Manuel utilisateur
Fluke
Fluke T100 Manuel utilisateur
Fluke
Fluke 9640A Series Manuel utilisateur
Fluke
Fluke 5440B/AF Manuel utilisateur
Fluke
Fluke 6100B Manuel utilisateur
Fluke
Fluke 709 Manuel d'instructions
Fluke
Fluke FIBER QUICKMAP Manuel utilisateur
Fluke
Fluke 5500A Manuel utilisateur
Fluke
Fluke MicroScanner Pro Manuel utilisateur
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Mercury
Mercury TSL01 Manuel utilisateur
