FLIR BLACKFLY S USB Vision Manuel utilisateur

INSTALLATIONGUIDE

FLIRBLACKFLY®S

Version 4.0

Revised 5/4/2017

FCC Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesirable operation.

Korean EMCCertification

The KCC symbol indicates that this product complies with Korea’s Electrical Communication Basic Law regarding

EMC testing for electromagnetic interference (EMI) and susceptibility (EMS).

Hardware Warranty

The warranty for the BlackflyS camera is 3 years. For detailed information on how to repair or replace your

camera, please see the terms and conditions on our website.

Export Control

The ECCN for this product is EAR099.

WEEE

The symbol indicates that this product may not be treated as household waste. Please ensure this

product is properly disposed as inappropriate waste handling of this product may cause potential

hazards to the environment and human health. For more detailed information about recycling of this

product, please contact us.

Trademarks

Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR

Systems, Inc. and/or its subsidiaries.

Licensing

To view the licenses of open source packages used in this product please see What open source packages does

firmware use?

Table of Contents

1 Blackfly S Installation Guide 1

2 Handling Precautions and Camera Care 2

3 BlackflyS Installation 3

3.1 Preparing for Installation 3

3.2 Installing Your Interface Card and Software 4

3.3 Installing Your BlackflyS 6

3.4 Powering Your BlackflyS 7

4 Tools to Control the BlackflyS 8

4.1 Using the Spinnaker® Software Development Kit 8

4.1.1 SpinView Camera Evaluation Application 8

4.1.2 Custom Applications Built with the Spinnaker API 8

4.2 Using GenICam Applications 9

5 Configuring BlackflyS Setup 11

5.1 Configuring Camera Drivers 11

5.2 Configuring the IP Address—GigEonly 11

5.3 Allocating Bandwidth—GigEonly 12

5.3.1 Determining Bandwidth Requirements 12

5.4 Configuring Other Ethernet Settings—GigEonly 13

5.4.1 Stream Channel Destination Address 13

5.4.2 Heartbeat 13

5.5 Camera Firmware 15

5.5.1 Determining Firmware Version 15

5.5.2 Upgrading Camera Firmware 15

6 BlackflyS Physical Interface 16

6.1 BlackflyS Physical Description 16

6.2 BlackflyS Dimensions 17

6.3 Interface Connector 19

6.3.1 Ethernet Connector 19

6.3.2 USB3.1 Connector 19

6.4 Interface Cables 20

6.5 Interface Card 20

6.6 General Purpose Input/Output (GPIO) 21

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide i

6.7 Mounting with the Case or Mounting Bracket 23

6.8 Case Temperature and Heat Dissipation 24

6.9 Lens Mounting 25

6.9.1 Back Flange Distance 25

6.10 Non-Volatile Flash Memory 26

6.11 Dust Protection 26

6.12 Infrared Cut-Off Filters 27

7 Input/Output Control 28

7.1 General Purpose Input/Output (GPIO) 28

7.2 GPIO Electrical Characteristics 30

8 Troubleshooting 32

8.1 Support 32

8.2 Status Indicator LED 33

Contacting Us 34

Revision History 34

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide ii

1 Blackfly S Installation Guide

Welcome to the BlackflyS camera. We offer a number of resources to assist you with the BlackflyS.

nRelease Notes—information about the current firmware release including feature additions or changes,

bug fixes, and known issues.

nSpecifications—information about the camera model as it performs with the current firmware.

nGetting Started—quick start guide for installing the camera and software.

nInstallation Guide—information about installing the camera and SDK, the physical interface and

mechanical properties, troubleshooting and how to get help. This document is available as a PDF for

download or as a webpage included in the firmware release package.

nTechnical Reference—information about the features supported by the camera model with the current

firmware, including: image format control, acquisition control, sequencing, binning/decimation, and others.

This document is available as a PDF for download or as a webpage included in the firmware release

package.

nFirmware—programming inserted into the programmable ROM of the camera that can be updated in-field.

New firmware packages are available for download and include both the firmware file and documentation.

nSpinnaker SDK—software development kit that provides GenICam-compliant controls to create

applications for the camera. Spinnaker is available for download. Each installation includes API

documentation for C, C++, and C#.

Our website provides additional information in our Knowledge Base and Technical Application Note library. As

well, the Downloads site is the portal to access documentation and firmware updates.

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide 1

2 Handling Precautions and Camera Care

Warning! Do not open the camera housing. Doing so voids the

Hardware Warranty described in the Terms and Conditions on

our website.

Your FLIR digital camera is a precisely manufactured device and should be handled with care. Here are some tips

on how to care for the device.

nAvoid electrostatic charging.

nWhen handling the camera unit, avoid touching the lenses. Fingerprints will affect the quality of the image

produced by the device.

nTo clean the lenses, use a standard camera lens cleaning kit or a clean dry cotton cloth. Do not apply

excessive force.

nExtended exposure to bright sunlight, rain, dusty environments, etc. may cause problems with the

electronics and the optics of the system.

nAvoid excessive shaking, dropping or any kind of mishandling of the device.

Title Article

Cleaning the imaging surface of your

camera

Knowledge Base Article

10243

Related Knowledge Base Articles

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide 2

3 BlackflyS Installation

3 BlackflyS Installation

3.1 Preparing for Installation

What system configuration is recommended?

Operating

System CPU RAM Ports Software to run and

compile example code

Recommended

System

Configuration

Windows7,

Windows8, or

Windows10

(32- or 64-bit)

Intel i5 4 GB Intel USB3

host controller

Microsoft Visual Studio 2010,

Visual Studio 2013, or

Visual Studio 2015

Note: Refer to Technical Application Note 10359 for important

information on recommended USB 3.0 system components.

Do you have all the parts you need?

To install your camera you will need the following components:

nFor GigEcameras—Ethernet cable (see Interface Cables) and Powered Ethernet switch or Ethernet power

injector (if using PoE)

nFor USB3 cameras—USB 3.0 cable (see Interface Cables)

n6-pin GPIOcable (see General Purpose Input/Output (GPIO))

nC-mount Lens (see Lens Mounting )

nTripod adapter (optional) (see Mounting with the Case or Mounting Bracket)

nInterface card (see Interface Card)

FLIR sells a number of the additional parts required for installation. To purchase, visit the Accessories page.

Do you have a downloads account?

The downloads page has many resources to help you operate your camera effectively, including:

nSpinnaker®SDKsoftware, including drivers (required for installation)

nFirmware updates and release notes

nDimensional drawings and CADmodels

nDocumentation

To access the software and firmware downloads you must have a downloads account.

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide 3

3 BlackflyS Installation

1. Go to our website: www.ptgrey.com.

2. In the upper right corner, click Register.

3. Complete the form, then click Register.

After you submit your registration, you will receive an email with instructions on how to activate your account.

3.2 Installing Your Interface Card and Software

1. Install your Interface Card

Ensure the card is installed per the manufacturer's instructions.

Connect the internal IDE or SATApower connector on the card to the computer power

supply.

Alternatively, use your PC's built-in host controller, if equipped.

Open the Windows Device Manager. Ensure the card is properly installed. Ethernet cards appear under Network

Adapters. USB3 cards appear under Universal Serial Bus Controllers. An exclamation point (!) next to the

card indicates the driver has not yet been installed.

2. Install the Spinnaker® Software

Note: For existing users who already have Spinnaker installed,

we recommend ensuring you have the latest version for optimal

performance of your camera. If you do not need to install

Spinnaker, use SpinView to install and enable drivers for your

card.

a. Login to the Downloads page.

b. Select your Product Family,Camera Model and Operating System from the drop-down lists.

c. Click on the Software search results to expand the list.

d. Click the appropriate link to begin the download and installation.

After the download is complete, the Spinnaker setup wizard begins. If the wizard does not start automatically,

double-click the .exe file to open it. Follow the steps in each setup dialog.

3. For Ethernet cards: Enable jumbo frames

a. In Start->All Programs-> Point Grey Spinnaker SDK->SpinView, right click on the Network Adapter

and select Adapter Configuration, then select IP Configuration.

b. Click Open Network Connections.

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide 4

3 BlackflyS Installation

c. Click Change Settings.

d. Click on the Advanced tab and from the Settings list select Jumbo Packet.

e. Set the Value to 9014 Bytes and click OK.

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide 5

3 BlackflyS Installation

3.3 Installing Your BlackflyS

1. Install the Tripod Mounting Bracket (optional)

The ASA and ISO-compliant tripod mounting bracket attaches to the camera using the

included screws.

2. Attach a Lens

Unscrew the dust cap from the lens holder to install a lens.

3. Connect the interface Card and Cable to the Camera

Plug the interface cable into the host controller card and

the camera. The cable jack screws can be used for a

secure connection.

When the camera is first connected, the operating system automatically installs the camera driver. Camera

drivers are available with the Spinnaker SDK installation.

a. If using PoE, connect a powered Ethernet switch or Ethernet power injector in between the card and the

camera.

4. Plug in the GPIO connector if required

GPIOcan be used for power, trigger, and strobe.

5. Confirm Successful Installation

Run the SpinView application: Start->All Programs-> Point Grey Spinnaker->SpinView

The SpinView application can be used to test the camera's image acquisition capabilities.

Changes to your camera's installation configuration can be made using the SpinView application.

5/4/2017

Integrated Imaging

Solutions Inc.

FLIRBlackfly®S Installation Guide 6

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels FLIR Appareil photo numérique

FLIR

FLIR FC S Series Instructions de montage

FLIR

FLIR M-Series Manuel utilisateur

FLIR

FLIR USB3 Vision CHAMELEON 3 Manuel utilisateur

FLIR

FLIR Txxx series Manuel utilisateur

FLIR

FLIR FIREFLY Manuel utilisateur

FLIR

FLIR Elara FR-345-EST Manuel utilisateur

FLIR

FLIR GRASSHOPPER 3 Series Manuel d'utilisation et d'entretien

FLIR

FLIR Tau Camera TAU-0035-00-10 Manuel utilisateur

FLIR

FLIR Exx series Manuel utilisateur

FLIR

FLIR AX Series Manuel utilisateur

FLIR

FLIR Elara DX Series Manuel utilisateur

FLIR

FLIR USB3 Vision Flea3 Manuel utilisateur

FLIR

FLIR A400 Series Manuel utilisateur

FLIR

FLIR Scout Manuel utilisateur

FLIR

FLIR ThermaCAM QuickView Manuel utilisateur

FLIR

FLIR 310 Series Manuel utilisateur

FLIR

FLIR Quasar Gen III CP-6302 Series Manuel utilisateur

FLIR

FLIR FIREFLY Manuel utilisateur

FLIR

FLIR Ariel CM-3102 Manuel

FLIR

FLIR Ariel CM-3202-11-I Manuel utilisateur

FLIR

FLIR C2 Manuel utilisateur

FLIR

FLIR Lorex LW3211-C Manuel utilisateur

FLIR

FLIR M500 Manuel utilisateur

FLIR

FLIR LADYBUG 5 USB3 Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur