FlexRadio Systems Maestro Manuel utilisateur

Maestro Tilt Hinged Feet Installation

Guide Installation Guide

April 18, 2016

The following guide will provide the necessary step-by-step procedure for installing the constant torque

Tilt Hinged Feet on a Maestro Control Console for the FLEX-6000 Signature Series SDR.

Table of Contents

OBTAINING TECHNICA L SU PP OR T ............................................................................................................... 2

GETTING STARTED........................................................................................................................................... 2

Packaging and Tilt Hinged Feet Contents ............................................................................................... 2

Required Tools ........................................................................................................................................ 3

PREPARING FOR THE MAESTRO TILT HINGED FEET INSTALLATION ............................................................................ 3

PREP ARING THE WORK SUR FACE ............................................................................................................... 3

Using the Top Foam Packing Material as an Work Surface Offset ......................................................... 3

Place the Maestro on the Work Surface Offset ...................................................................................... 4

INSTALLING THE MAESTRO TILT HINGED FEET ...................................................................................................... 4

Locating the Tilt Hinged Feet Mounting Screw Holes ............................................................................. 4

Orientating the Tilt Hinged Feet Components ........................................................................................ 5

Install Plugs in Feet................................................................................................................................. 5

Verify the Correct Orientation of the Feet .............................................................................................. 6

Verify the Correct Orientation of the Hinges .......................................................................................... 7

Attach Hinges to Feet ............................................................................................................................. 7

Prepare Hinge-Foot Assembly for Attachment to Maestro .................................................................... 8

Attach Hinge-Foot Assembly to Maestro................................................................................................ 8

ADJUSTING THE TILT HINGED FEET ..................................................................................................................... 9

Obtaining Technical Support

If you encounter any issues installing or operating SmartSDR for Windows with a FlexRadio Systems

Signature Series software defined radio, please use our on-line Community to find information about

SmartSDR and the FLEX-6000 radios. If you need assistance using the Community, please refer to the

community topic “How to use the FlexRadio Systems Support Community”.

If you are unable to find an existing answer to your issue on the Community, please contact FlexRadio

Systems technical support by opening a HelpDesk support ticket on-line at

https://helpdesk.flexradio.com/

For details on how to submit a HelpDesk support ticket, please refer to the following URL:

https://helpdesk.flexradio.com/hc/en-us/articles/202118688-How-to-Submit-a-Request-for-Technical-

Support.

Hours of Operation: Our Technical Support engineers are available Monday-Friday from 9:00am-5:30pm

Central Time. If you contact Support after business hours, on a holiday or weekend, we will respond to

your request for assistance during regular business hours in the order the tickets were received.

Getting Started

Packaging and Tilt Hinged Feet Contents

Remove the Maestro Tilt Hinged Feet kit contents from the packaging and verify that the following items

are included before proceeding. Refer to the image below.

Two (2) tilting Tilt Hinged Feet

One (1) Hinge, ST-11A-140SA-50 (hinge “A”)

One (1) Hinge, ST-11A-140SB-50 (hinge “B”)

Eight (8) Attachment screws, M4 x 8mm

Four (4) Plastic plugs

Required Tools

A #2 Phillips screwdriver is required (not supplied). Note a magnetic tipped screwdriver

will facilitate the installation of the attachment screws.

Preparing for the Maestro Tilt Hinged Feet Installation

If the Maestro is powered on, power it off by pressing the Power Button on the top. Disconnect all cables.

Use a flat, well-lighted surface such as a table or work bench to perform the Maestro Tilt Hinged Feet

installation.

You may want to use several small containers to store and organize the screws that will be used as part of

the Tilt Hinged Feet installation.

Make sure to observe basic ESD control procedures to prevent static discharges that may damage

sensitive electronics components inside the Maestro, such as grounding yourself to reduce static electrical

build up.

Preparing the Work Surface

The top of the foam insert used in packing the Maestro will be used as a work surface to prevent

scratches to the front of the unit and to level the Maestro while attaching the Tilt Hinged Feet.

Using the Top Foam Packing Material as an Work S urface Offset

The knobs on the front of the Maestro does not allow for the unit to lie flat on its front to facilitate easy

installation of the Tilt Hinged Feet. Therefore the part of the Maestro packing material will be used as an

offset to create a flat work surface for installing the Tilt Hinged Feet.

As shown in the picture below, use the top of the foam packing material and the plastic bag the Maestro

was packed in to create a convenient work surface offset. Allow the plastic bag to extend to the left to

protect the tops of the knobs. Alternately a soft cloth may be used in place of the plastic bag if desired.

Place the Maestro on the Work Surface Offset

As shown in the picture below, place the Maestro touch screen display face down on the top of the foam

packing material allow the knobs to rest on the covered work surface. This will allow of the Maestro to lie

flat for the installation of the Tilt Hinged Feet.

Installing the Maestro Tilt Hinged Feet

Once the Maestro is properly oriented, the Tilt Hinged Feet can be conveniently installed.

Locating the Tilt Hinged Feet Mounting Screw Holes

Locate the four (4) M4 mounting screw holes at the bottom center of the Maestro as shown below with

the four arrows.

Orientating the Tilt Hinged Feet Components

Orient feet bases separated by a few inches as shown below. Place a set of two (2) screws at the top and

bottom of each foot. Position hinge from bag marked: ST-11A-140SB-50 on left. Position hinge from bag

marked: SA-11A-140SA-50 on right side. Each hinge is also marked on bottom with “A” and “B” for easy

identification.

Install Plugs in Feet

Insert two each of the plastic plugs into each foot as shown below.

Below is an image showing all 4 plastic plugs installed.

Verify the Correct Orientation of the Feet

The two (2) mounting holes on the feet are not centered; they are closer to one end of the foot than the

other. Before installing the hinges, verify the orientation of each foot so that the mounting holes are

farther away from you, towards the Maestro.

Verify the Correct Orientation of the Hinges

There is a left and right hinge designated as “A and “B” which is stamped on the underside of each hinge

as shown below. The “B” hinge will be installed on the left foot and the “A” hinge will be installed on the

right foot. Please note that each hinge consists of a narrow and wide tab. The narrow tab, shown as the

one at the bottom is the part of the hinge that will be attached to the foot in the next installation step.

Attach Hinges to Feet

Flip the left or “B” hinge over and attach it to the foot with two (2) M4 attachment screws using a #2

screwdriver. Tighten snugly, but do not overtighten. Repeat the procedure for the right or “A” hinge as

shown below.

Prepare Hinge-Foot Assembly for Attachment to Maestro

Rotate Hinge “A” and “B” tabs up to vertical position as shown below in preparation for installing each

foot on the Maestro.

Attach Hinge-Foot Assembly to Maestro

Position the right hinge-foot assembly “A” on the right side back of Maestro as shown below. Using a #2

screwdriver, attach with two M4 screws. Tighten snugly, but do not overtighten. Repeat the procedure

for attaching the left hinge-foot assembly “B” on the left side back.

Below shows an image of the completed installation of both hinge-foot assemblies.

Adjusting the Tilt Hinged Feet

The Tilt Hinged Feet are adjusted with the Tilt Hinged Feet on a table and the Maestro in an upright

position.

Lift Maestro off foam work surface offset and place feet on a flat surface. Grasp the Maestro with two

hands as shown below and tilt to the desired operating angle.

Autres manuels pour Maestro

Table des matières

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur