Fike 10-2983 Manuel utilisateur

SOLUTIONS

Fire Protection

Explosion Protection

Overpressure Protection

Pressure Activation

Doc. P/N 06-905

Rev. 1 / December 2018

PRODUCT MANUAL

Output Analyzer

P/N 10-2983

This document may not be reproduced, in whole or in part, by any means without the prior written consent of Fike.

TRADEMARKS

Fike®, SHP-Pro®, Cheetah® Xi, CyberCat®, DuraQuench™, Precise Vision™, EPACO® are registered trademarks of

Fike. All other trademarks, trade names, or company names referenced herein are the property of their respective

owners.

ERRORS AND OMMISSIONS

While every precaution has been taken during the preparation of this document to ensure the accuracy of its

content, Fike assumes no responsibility whatsoever for errors or omissions.

Fike reserves the right to change product designs or specifications without obligation and without further notice in

accordance with our policy of continuing product and system improvement.

READER QUESTIONS AND RESPONSES

If you have any questions regarding the information contained in this document, or if you have any other inquiries

regarding Fike products, please call Fike’s Customer Support Department at (800)-979-FIKE (3453), option 21.

Fike encourages input from our distributors and end users on how we can improve this manual and even the product

itself. Please contact us at feed[email protected]. Any communication received becomes the property of Fike.

TERMS AND CONDITIONS OF SALE

Because of the many and varied circumstances and extreme condition under which Fike’s products are used, and

because Fike has no control over this actual use, Fike makes no warranties based on the contents of this document.

FIKE MAKES NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A SPECIFIC PURPOSE. Refer to

www.fike.com/terms-conditions for Fike’s full TERMS AND CONDITIONS OF SALE.

Do not alter, modify, copy, or otherwise misappropriate any Fike product, whether in whole or in part. Fike assumes

no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy, or

otherwise misappropriation of Fike products.

Do not use any Fike products for any application for which it is not intended. Fike shall not be in any way liable for

any damages or losses incurred by you or third parties arising from the use of any Fike product for which the product

is not intended by Fike.

You should install and use the Fike products described in this document within the range specified by Fike, especially

with respect to the product application, maximum ratings, operating supply voltage range, installation and other

product characteristics. Fike shall have no liability for malfunctions or damages arising out of the use of Fike products

beyond such specified ranges.

You should install and use the Fike products described in this document in compliance with all applicable laws,

standards, and regulations. Fike assumes no liability for damages or losses occurring as a result of your

noncompliance with applicable laws and regulations.

It is the responsibility of the buyer or distributor of Fike products, who distributes, disposes of, or otherwise places

the product with a third party, to notify such third party in advance of the contents and conditions set forth in this

document. Fike assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized

use of Fike products.

QUALITY NOTICE

Fike is an ISO 9001:2015 certified company. Prior to shipment, we thoroughly test our products and review our

documentation to assure the highest quality in all respects.

PAGE / i

Doc. P/N 06-905

Rev. 1 / December 2018

Table of Contents

1.0 GENERAL .................................................................................................................................................................1

2.0 FEATURES................................................................................................................................................................3

3.0 APPROVALS.............................................................................................................................................................3

4.0 SAFETY INFORMATION............................................................................................................................................3

5.0 BATTERY LIFE...........................................................................................................................................................4

6.0 CONTROLS/INTERFACE ...........................................................................................................................................4

6.1. Navigation Menu............................................................................................................................................5

7.0 EPC TESTING............................................................................................................................................................5

7.1. EPC Operational Overview .............................................................................................................................5

7.2. Interpreting EPC Measured Results ...............................................................................................................6

7.3. EPC Testing Procedures..................................................................................................................................6

7.3.1. Test 1: EPC Series Firing Circuit Activation Current Test...................................................................6

7.3.2. Test 2: EPC Supervisory Current Test ................................................................................................8

7.3.3. Test 3: EPC Field Test.........................................................................................................................9

7.3.4. Test 4: Field Wiring Supervisory Current Test.................................................................................10

8.0 IRM TESTING .........................................................................................................................................................11

8.1. IRM Operational Overview...........................................................................................................................11

8.2. Interpreting IRM Measured Results .............................................................................................................11

8.3. IRM Testing Procedures ...............................................................................................................................11

9.0 FIRE ARM TESTING................................................................................................................................................12

9.1. Fire ARM Operational Overview ..................................................................................................................12

9.2. Interpreting Fire ARM Measured Results.....................................................................................................13

9.3. Fire ARM Testing Procedures.......................................................................................................................13

10.0 EP ARM TESTING...................................................................................................................................................14

10.1.EP ARM Operational Overview ....................................................................................................................14

10.2.Interpreting EP ARM Measured Results.......................................................................................................14

10.3.EP ARM Testing Procedures .........................................................................................................................15

11.0 VIEW MEMORY .....................................................................................................................................................16

12.0 CLEAR MEMORY....................................................................................................................................................16

13.0 CHECK BATTERY CHARGE (Chk Batt Chrg).............................................................................................................16

14.0 TECHNICAL SUPPORT............................................................................................................................................16

PAGE / ii

Doc. P/N 06-905

Rev. 1 / December 2018

List of Figures

Figure 1.0-1 Output Analyzer…………………………………………………………………………………………………………………………………..1

Figure 6.0-1 Output Analyzer Controls and Interface……………………………………………………………………………………………….2

Figure 7.3.1-1 EPC Series Firing Circuit Activation Current………………………………………………………………………………………..6

Figure 7.3.2-1 EPC Series Firing Circuit Supervisory Current Test………………………………………………………………………………8

Figure 7.3.3-1 Field Wiring Activation Current Test…………………………………………………………………………………………………..9

Figure 8.3-1 IRM Circuit Activation Current Test………………………………………………………………………………………………….....11

Figure 9.3-1 Fire ARM Circuit Activation Current Test……………………………………………………………………………………………..13

Figure 10.3-1 EP ARM Series Firing Circuit Activation Current Test…………………………………………………………….…………...15

List of Tables

Table 6.1-1 Menu Options.............................................................................................................................................5

Doc. P/N 06-905

Rev. 1 / December 2018

PAGE / 1

1.0 GENERAL

Weight: 6.5 ounce (184 grams)

Size: 5.75 x 3.5 x 1.125 inches (146 x 89 x 28.6 mm)

Temperature Limitations: 32-120°F (0-49°C)

Power Requirements: Rechargeable Lithium-Ion battery

Casing: ABS plastic

Figure 1.0-1 Output Analyzer

The Fike Output Analyzer (10-2983) is a compact, rechargeable, hand-held device that is designed to be used by Fike

factory-trained and certified service technicians to test and verify operation of the following Fike releasing

components:

Explosion Protection Controller (EPC)*, P/N E10-0066.

Impulse Release Module (IRM), P/N 10-2748.

Fire Agent Release Module (Fire ARM), P/N 10-1832.

Explosion Protection Agent Release Module (EP-ARM), P/N E10-010.

The device’s portability and ease of use makes it ideal for performing quick tests that provide peace of mind and

help you know your system is working properly.

The Output Analyzer comes with the following components:

EPC Test

Harness -

Output and

Sensory Input

IRM/ARM Test

Harness -

Output or

Supervisory

Current Test

Field Box Test

Connector

w/14-inch

long leads and

alligator clips

*Purchase of P/N E10-070 required to conduct EPC testing.

IRM/ARM Test Harness

14-inch Long Leads with Alligator Clips

P/N 10-2986

P/N 10-2987

P/N 10-2988

PAGE / 2

Doc. P/N 06-905

Rev. 1 / December 2018

0Shunt

Current test –Min.

resistance shunt

10Ω Resistor

Current test –Max.

resistance resistor

(jumper)

75Ω Resistor

EPC and field wiring -

Supervisory resistor

(jumper)

2-Position Plug

Current test –Field wiring

plug

Magnetic Hanger

USB Charging Cable

USB A to USB C, 5Vdc

ONLY!

DO NOT charge at higher voltages!

Electrical damage will occur!

Case

NOTE: The Output Analyzer comes with a charging cord but does not come with a wall charger or a 1-Ohm Resistor

used in EPC testing.

Please obtain a charger to fully charge the battery before testing. To ensure this device remains compliant with EMC

Directive 2014/30/EU, the unit shall not be used while charging the battery and the battery charger used for charging

the device shall be compliant with the requirements of EN61326-1.

The 1-Ohm Resistor is included in the E10-070 kit purchased by EP Service Technicians, of which the 10-2983 Output

Analyzer is a part.

USB A

USB C

P/N 10-2989

P/N 10-2991

P/N 02-16516

P/N 02-16502

P/N 02-16505

P/N 10-2990

P/N 02-16506

Doc. P/N 06-905

Rev. 1 / December 2018

PAGE / 3

2.0 FEATURES

On-off switch

Back-lit LCD display

Rechargeable battery

Removable test jumpers

Durable plastic housing

Can be used to test fire the EPC

Replaces cumbersome and outdated flashbulbs for testing

Substitutes portable oscilloscopes for electrical measurements

Finds series/parallel wiring faults in an EPC system by examining supervisory current levels anywhere in the field

wiring loop

3.0 APPROVALS

The Analyzer has been tested and complies with the limits for a Class A digital device, pursuant to Part

15 of FCC rules. When the equipment is operated in a commercial environment, these limits provide

reasonable protection against harmful interference. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference with radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case the user will be required to correct the

interference at his or her own expense. Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate this equipment.

This product complies with the essential requirements of the following applicable European directive(s)

and carries the CE marking accordingly: (1) EMC Directive 2014/30/EU; and (2) RoHS Directive

2011/65/EU.

4.0 SAFETY INFORMATION

IMPORTANT: Pack and safely store the Fike Output Analyzer when not in use. Do not allow the Analyzer to remain

connected to live circuitry, as this will reduce battery life.

WARNING - When wired to the EPC, the Output Analyzer is capable of activating the EPC when the

ACTIVATE button is pressed, even when the device is turned off. Prior to using the tool, verify that all

GCA’s connected to the EPC series firing circuit (P3-2) are disconnected from the circuit. For ARM (10-

1832) testing, disarm the GCA as noted in the 06-106 ARM Manual. For IRM (10-2748) testing, remove

the IVO from the container and IRM.

CAUTION –Do not use the Output Analyzer if it appears to be damaged or if the device doesn’t appear

to be working according to the supplied user instructions.

CAUTION –Do not use the Output Analyzer on any solenoid circuit or damage will occur!

STATIC DISCHARGE –Use a grounding strap to eliminate static discharge sources prior to working with

GCAs.

PAGE / 4

Doc. P/N 06-905

Rev. 1 / December 2018

5.0 BATTERY LIFE

The device is shipped with only a partial charge; therefore, you’ll need to fully

charge the battery before you begin testing. One full charge typically takes about

1.5 hours to complete and will provide roughly 22 hours of use.

IMPORANT: The device will notify you when the battery is at 20%, at which time you’ll want to plug it in to charge

and preserve battery life. While you will be able to continue testing even when the battery falls to 20%, low battery

notifications will persist every 10 seconds until the unit is plugged in, which means it will interrupt your work.

The battery warning message can be cleared by turning the unit off, but the message will remain if you turn the unit

on again without charging. Remember that battery charge is displayed on initial power up, and you can check it

periodically by using Option 7 (Chk Batt Chrg) to keep track of usage.

6.0 CONTROLS/INTERFACE

On initial power up, the battery charge will display for three (3) seconds; this will help you gauge whether you can

complete all tests on the current charge. Next, the panel will display “Fike Analyzer Select Tool Use.” Once you see

this message, press and release the SELECT button to view the main menu.

Figure 6.0-1 Output Analyzer Controls and Interface

Jumper Port

-75 Ωresistor = Supervisory current test (EPC only).

10 Ωresistor = Simulates max field wiring resistance (EPC only).

-0 Ωshunt = Max current test (EPC, IRM, ARM).

USB C Port

- Battery charging

EPC or IRM/ARM Cable Port

-Connect EPC test cable or IRM/ARM test

cable.

Enter Button

- Activates displayed option.

Select Button

- Scrolls through menu options

Activate Button

- Simulates 4-20mA sensor activation.

- Used for EPC testing only.

Jumper

Cable

Charge

Battery @ 20%

Pwr off and CHRG

Table des matières

Autres manuels Fike Instrument de mesure

Fike

Fike FAAST XT 68-302 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur