Fike TWINFLEXpro Manuel utilisateur

26-1192 Issue 1

Fire Detection & Alarm System Repeater Panel

(Suitable for TWINFLEX®pro control panels from V2.00)

Repeater Panel Engineering and

Commissioning Manual

(TO BE RETAINED BY THE COMMISSIONING ENGINEER)

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

Fike’s policy is one of continual improvement and the right to change a specification at any time without notice is reserved. Whilst every

care has been taken to ensure that the contents of this document are correct at time of publication, Fike shall be under no liability

whatsoever in respect of such contents.

Due to the complexity and inherent importance of a life risk type system, training on this equipment is essential and commissioning should

only be carried out by competent persons.

Fike cannot guarantee the operation of any equipment unless all documented instructions are complied with, without variation.

E&OE.

TWINFLEX, Mulitpoint, Fike and Fike Corporation are registered trademarks of Fike Corporation and its subsidiaries. All other trademarks,

trade names or company names referenced herein are the property of their respective owners.

Fike equipment is protected by one or more of the following patent numbers: GB2426367, GB2370670, EP1158472, PT1035528T,

GB2346758, EP0917121, GB2329056, EP0980056, GB2325018, GB2305284, EP1174835, EP0856828, GB2327752, GB2313690

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

Contents

Introduction........................................................................................................................................................... 5

System Design...................................................................................................................................................... 5

Equipment Guarantee .................................................................................................................................. 5

Anti-Static Handling Guidelines.................................................................................................................... 5

Warning........................................................................................................................................................ 5

EMC.............................................................................................................................................................. 6

The TWINFLEX®pro System................................................................................................................................ 6

Repeater Panel, Remote Display Unit (RDU) ..................................................................................................... 6

Mounting the Repeater Panel.............................................................................................................................. 7

Physical Dimensions .................................................................................................................................... 9

General Assembly .............................................................................................................................................. 10

Ribbon Cable Connection .......................................................................................................................... 10

Fixing Front Panel ...................................................................................................................................... 10

Installation and Commissioning ....................................................................................................................... 11

Topology & Cabling.................................................................................................................................... 11

Maximum Cable Lengths............................................................................................................................ 11

Power Supply & Connections..................................................................................................................... 12

Power Connection Table.................................................................................................................. 12

Current Drawn by Single Repeater @ 24.0V DC............................................................................. 12

Separate Power Supply Requirements............................................................................................ 12

Repeater Back Board Power supply connections............................................................................ 12

Peripheral Bus Connections....................................................................................................................... 13

Peripheral Bus Connection Table .................................................................................................... 13

Example of Panel Peripheral Bus Connections Showing EOL Resistor.......................................... 13

Repeater Back Board Peripheral Bus connections.......................................................................... 13

Main Control Panel Peripheral Bus Settings.............................................................................................. 14

Repeater Panel Settings ............................................................................................................................ 14

LCD Contrast.................................................................................................................................... 14

Setting Repeater Number ................................................................................................................ 15

Repeater Buzzer .............................................................................................................................. 15

Powering Up..................................................................................................................................... 15

Commissioning........................................................................................................................................... 16

Fault finding................................................................................................................................................ 16

General Operation of Repeater Panel............................................................................................................... 17

Control Panel Front .................................................................................................................................... 17

LED Indication............................................................................................................................................ 17

Fire Alarm Controls..................................................................................................................................... 18

System Controls ......................................................................................................................................... 18

Access Levels............................................................................................................................................. 18

Access Level 1 (Normal): Controls Enabled LED off....................................................................... 19

Access Level 2 (user): Controls Enabled LED on............................................................................ 19

End User Training............................................................................................................................................... 20

Maintenance........................................................................................................................................................ 20

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

Technical Data .................................................................................................................................................... 21

Repeater Panel Specification..................................................................................................................... 21

Fire Alarm System Notice.................................................................................................................................. 22

To Enable the Control Panel Keys............................................................................................................. 22

To Manually Operate the Fire Alarm Sounders.......................................................................................... 22

Following a Fire Alarm Operation............................................................................................................... 22

Following a Fault Condition........................................................................................................................ 22

Important Notes .................................................................................................................................................. 23

Fire Alarm User Notice....................................................................................................................................... 24

Engineers Notes ................................................................................................................................................. 25

Technical Support .............................................................................................................................................. 26

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

Introduction

This Manual is intended as a guide to the engineering and commissioning principles of the

TWINFLEX®pro Repeater Panel and covers the system hardware information only.

Due to the complexity and inherent importance of a system covering a ‘Life Protection Risk’, training on

this equipment is essential and commissioning should only be carried out by competent and approved

persons. For further details of the availability of commissioning services, please contact your supplier.

System Design

This document does not cover Fire Alarm system design and a basic understanding is

assumed.

A knowledge of BS5839: Pt 1: 2002: Fire Detection and Alarm Systems for Buildings

is essential.

It is strongly recommended that a suitably qualified and competent person is consulted in

connection with the Fire Alarm System design and that the entire system is commissioned

in accordance with the current national standards and specifications.

Equipment Guarantee

The equipment carries no warranty unless the system is installed, commissioned and

serviced in accordance with this manual and the relevant standards by a suitably qualified

and competent person or organisation

Anti-Static Handling Guidelines

Immediately prior to handling any PCBs or other static sensitive devices, it is essential to

ensure that a personal connection to earth is made with an anti-static wrist-strap or

similar apparatus.

Always handle PCBs by their sides and avoid touching any components. PCBs should also

be stored in a clean dry place, which is free from vibration, dust and excessive heat and is

protected from mechanical damage.

Warning Do not attempt to install this equipment until you have fully read and understood

this manual.

Failure to do so may result in damage to the equipment and could invalidate the warranty.

For technical support please contact your distributor. Do not call the Fike Safety

Technology support department unless your distributor has first given their advice and

attempted to rectify the issue.

Technical support will not be available if the instruction manual has not been read and

understood. Please have this instruction manual available whenever you call for technical

support.

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

EMC This equipment when installed is subject to the EMC directive 2004/108/EC. It is also

subject to UK Statutory Instrument 2006 No. 3418.

To maintain EMC compliance, this system must be installed as defined within this manual.

Any deviation from this renders the installer liable for any EMC problems that may occur

either to the equipment or to any other equipment affected by the installation.

The TWINFLEX®pro System

The TWINFLEX®pro system is an intelligent ‘2-wire’ system utilising a conventional type cabling format.

The system is classed as ‘Analogue non-addressable’ due to the architecture used within the design. All

field devices including sounders can be connected to the zone via a common 2-core screened cable.

The devices communicate with the control panel using the ‘TWINFLEX®’ data protocol.

Repeater Panel, Remote Display Unit (RDU)

The TWINFLEX®pro repeater panel is smaller than the TWINFLEX®pro control panel.

It does not itself connect to or control detection devices. Instead, it connects to a control panel and

reports events which occur on the control panel.

It can also perform system controls over the network (i.e. Silence Alarms, Reset, Sound Alarms &

Silence Buzzer).

A maximum of 8 repeater panels can be connected to a single control panel.

The maximum cable length from the control panel to a repeater is 500 metres. If 8 repeaters are used

they must all be within the maximum 500 metres cable length.

All external connections are made on the back board. The Ext Switches on the back board are not

currently used and are for a future development.

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

Mounting the Repeater Panel

First identify the proposed location for the repeater panel. Ensure that the repeater panel will be easily

accessible and that account is taken of any subsequent work that may affect access.

The repeater panel should be located at an access point to a building which is not covered by the main

panel. Repeaters can also be located in other buildings which are connected to the main fire alarm

panel. It should be mounted on a flat, vertical wall at a height where the indicators may be seen without

difficulty.

Do not locate the repeater panel at high level where stepladders or other access equipment may

be required, in spaces with restricted access, or in a position that may require access panels to

be removed.

Do not locate the repeater panel where extremes of temperature or humidity may occur i.e. close

to a heat source, or where there is any possibility of condensation or water ingress.

Like all electronic equipment, the repeater panel may be affected by extreme environmental conditions.

The position selected for its installation should therefore be clean and dry, not subjected to high levels

of vibration or shock and at least 2 metres away from any pager or radio transmitting equipment.

Ambient temperatures should be within the range given within the Technical Data section, e.g. not

directly over a radiator or heater.

In common with all microprocessor-controlled panels, the repeater panel may operate erratically or may

be damaged if subjected to lightning induced transients. Proper earth/ground connections will greatly

reduce susceptibility to this problem.

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

Physical Dimensions

TWINFLEX®pro Repeater Panel Engineering and Commissioning Manual

General Assembly

Ribbon Cable Connection

Fixing Front Panel

Autres manuels pour TWINFLEXpro

Table des matières

Autres manuels Fike Panneau de contrôle

Fike

Fike FIK-RA2000 Manuel technique

Fike

Fike CIE-A-200 Manuel utilisateur

Fike

Fike FCP-2100ECS Manuel utilisateur

Fike

Fike GB2426367 Manuel utilisateur

Fike

Fike TWINFLEXpro Manuel utilisateur

Fike

Fike FCP-300 Manuel utilisateur

Fike

Fike FCP-75 Manuel utilisateur

Fike

Fike FIK-5496 Manuel utilisateur

Fike

Fike FCP-2100 Manuel utilisateur

Fike

Fike Twinflex pro2 Manuel utilisateur

Fike

Fike FIK-RA100BD Manuel technique

Fike

Fike Quadnet Manuel utilisateur

Fike

Fike FCP-75 Manuel utilisateur

Fike

Fike TWINFLEX SRP 100-0001 Manuel utilisateur

Fike

Fike SITA200plus Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques