Fike TWINFLEX SRP 100-0001 Manuel utilisateur

26-1361-02

TWINFLEX®SRP

Single Flood Zone Fire Suppression System

Control Panel

100-0001

(Suitable for TWINFLEX®SRP control panels from V01.000)

Control Panel Engineering and

Commissioning Manual

(TO BE RETAINED BY THE COMMISSIONING ENGINEER)

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

Fike’s policy is one of continual improvement and the right to change a specification at any time without notice is reserved. Whilst every

care has been taken to ensure that the contents of this document are correct at time of publication, Fike shall be under no liability

whatsoever in respect of such contents.

Due to the complexity and inherent importance of a life risk type system, training on this equipment is essential and commissioning should

only be carried out by competent persons.

Fike cannot guarantee the operation of any equipment unless all documented instructions are complied with, without variation.

E&OE.

TWINFLEX®, Mulitpoint, Fike and Fike Corporation are registered trademarks of Fike Corporation and its subsidiaries. All other trademarks,

trade names or company names referenced herein are the property of their respective owners.

Fike equipment is protected by one or more of the following patent numbers: GB2426367, GB2370670, EP1158472, PT1035528T,

GB2346758, EP0917121, GB2329056, EP0980056, GB2325018, GB2305284, EP1174835, EP0856828, GB2327752, GB2313690

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

Contents

GLOSSARY OF TERMS.........................................................................................................5

INTRODUCTION.....................................................................................................................6

System Design......................................................................................................................................... 6

Equipment Guarantee ............................................................................................................................. 6

Anti-Static Handling Guidelines............................................................................................................. 6

Warning .................................................................................................................................................... 6

EMC........................................................................................................................................................... 7

THE TWINFLEX®SRP SYSTEM ............................................................................................7

CONTROL PANEL..................................................................................................................9

Mounting the Control Panel.................................................................................................................... 9

Physical Dimensions............................................................................................................................... 9

Power Supply Unit................................................................................................................................. 11

General Assembly ................................................................................................................................. 12

Topology & Cabling............................................................................................................................... 13

System Wiring Schematic..................................................................................................................... 14

Control Panel Connections .................................................................................................................. 15

Main Display Board .................................................................................................................... 15

Releasing Connector Board .......................................................................................................16

Ethernet...................................................................................................................................... 17

Write Protect / Write Enable Switch............................................................................................ 17

USB-B......................................................................................................................................... 17

Buzzer Link: J1........................................................................................................................... 17

LCD Contrast: R4 .......................................................................................................................17

RSI Peripheral Bus Connections: A1, B1, SCRN or A2, B2, SCRN ..........................................18

Programmable Inputs 1-5: MI# +, MI# -, SCRN .........................................................................19

Fault Relay: C, N/C, N/O ............................................................................................................20

Programmable Relays 1-4: C, N/C, N/O..................................................................................... 20

Monitored Outputs 1 -3: MO# +, MO# -, SCRN..........................................................................21

Device Zones: Z1 - Z4 (TWINFLEX®Devices)...........................................................................23

Device Zones: Z1 - Z4 (Conventional Devices).......................................................................... 24

Zones: Z1 - Z4 RELEASING OPERATION (IVO OR SOLENOID) ............................................24

Auxiliary Power: AUX PWR 1-2, +, -, SCRN..............................................................................25

Battery: BAT+, BAT-...................................................................................................................25

Power Supply: VPSU+, VPSU-, EARTH.................................................................................... 26

Output De-rating......................................................................................................................... 26

Mains Input Wiring...................................................................................................................... 26

GENERAL OPERATION OF CONTROL PANEL.................................................................27

Zone Detection & Releasing Operation...................................................................................... 27

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

Hold State / Hold Sound Patterns...............................................................................................27

Auto/Manual operation ............................................................................................................... 28

Extinguishant Flow, Discharge Pressure Input Operation.......................................................... 28

Power Start Up with batteries only .............................................................................................28

Control Panel Front ............................................................................................................................... 29

LED Indication........................................................................................................................................ 29

Fire Alarm Controls............................................................................................................................... 32

System Controls.................................................................................................................................... 32

Extinguishant Release Controls .......................................................................................................... 32

Information Window .............................................................................................................................. 33

Access Levels and Codes .................................................................................................................... 33

Enter An Access Code ............................................................................................................... 34

Access Level 1 (Normal): ...........................................................................................................35

Access Level 2A (User):............................................................................................................. 37

Access Level 2B (Supervisor): ................................................................................................... 41

Access Level 3 (Engineer):.........................................................................................................46

INSTALLATION AND COMMISSIONING.............................................................................61

Installation 1st Stage.............................................................................................................................. 61

Maximum Cable Lengths ...................................................................................................................... 61

Installation 2nd Stage............................................................................................................................. 61

Commissioning...................................................................................................................................... 62

End User Training.................................................................................................................................. 62

Maintenance........................................................................................................................................... 62

FAULT FINDING...................................................................................................................63

Summary of Faults ................................................................................................................................ 63

Intermittent Zone Fault.......................................................................................................................... 63

Permanent Zone Faults......................................................................................................................... 63

False Alarms .......................................................................................................................................... 64

General Faults........................................................................................................................................ 64

Finding Zone Faults............................................................................................................................... 65

ADVANCED CONNECTIONS...............................................................................................66

Magnetic Door Hold Units..................................................................................................................... 66

TECHNICAL DATA...............................................................................................................67

Control Panel Specification.................................................................................................................. 67

Control Panel Ratings........................................................................................................................... 67

Control Panel Fuses and Protection.................................................................................................... 68

Factory Default Settings & Profiles, .................................................................................................... 69

BATTERY CALCULATIONS ................................................................................................71

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

INSTALLATION CHECKLIST...............................................................................................72

Stage 1.................................................................................................................................................... 72

Stage 2.................................................................................................................................................... 72

COMMISSIONING CHECKLIST ...........................................................................................73

Step 1...................................................................................................................................................... 73

Step 2...................................................................................................................................................... 73

Step 3...................................................................................................................................................... 73

Step 4...................................................................................................................................................... 73

CABLE CONTINUITY & INSULATION TEST RESULTS.....................................................74

FIRE ALARM SYSTEM NOTICE ..........................................................................................75

FIRE ALARM USER NOTICE...............................................................................................76

ENGINEERS NOTES............................................................................................................77

TECHNICAL SUPPORT........................................................................................................78

Glossary Of Terms

Acronym

Description

Acronym

Description

ASD

Automatic Smoke Detector

MCP

Manual Call Point

CIE

Control & Indicating Equipment

O/C

Open Circuit

DIVA

Direct Impulse Valve Actuator

O/P

Output

EOL

End Of Line

RSI

Remote Status Indicator

I/O

Input Output

S/C

Short Circuit

I/P

Input

SRM

Solenoid Releasing Module

IRM

Impulse Releasing Module

SRP

Single-hazard Releasing Panel

IVO

Impulse Valve Operator

OSP

On Site Programmer

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

Introduction

This Manual is intended as a guide to the engineering and commissioning principles of the TWINFLEX®

SRP 2-wire Fire Detection and Alarm system and covers the system hardware information only.

Due to the complexity and inherent importance of a system covering a ‘Life Protection Risk’, training on

this equipment is essential and commissioning should only be carried out by competent and approved

persons. For further details of the availability of commissioning services, please contact your supplier.

System Design

This document does not cover Fire Alarm system design and a basic understanding is

assumed.

Knowledge of BS5839: Pt 1: 2002: Fire Detection and Alarm Systems for Buildings

and BS 7273 Pt 1 : 2006 Code of Practice for the operation of fire protection

measures is essential.

It is strongly recommended that a suitably qualified and competent person is consulted in

connection with the Fire Alarm System design and that the entire system is commissioned

in accordance with the current national standards and specifications.

Equipment Guarantee

The equipment carries no warranty unless the system is installed, commissioned and

serviced in accordance with this manual and the relevant standards by a suitably qualified

and competent person or organisation

Anti-Static Handling Guidelines

Immediately prior to handling any PCBs or other static sensitive devices, it is essential to

ensure that a personal connection to earth is made with an anti-static wrist-strap or

similar apparatus.

Always handle PCBs by their sides and avoid touching any components. PCBs should also

be stored in a clean dry place, which is free from vibration, dust and excessive heat and is

protected from mechanical damage.

Warning Do not attempt to install this equipment until you have fully read and understood

this manual.

Failure to do so may result in damage to the equipment and could invalidate the warranty.

For technical support please contact your distributor. Do not call the Fike Safety

Technology support department unless your distributor has first given their advice and

attempted to rectify the issue.

Technical support will not be available if the instruction manual has not been read and

understood. Please have this instruction manual available whenever you call for technical

support.

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

EMC This equipment when installed is subject to the EMC directive 2004/108/EC. It is also

subject to UK Statutory Instrument 2006 No. 3418.

To maintain EMC compliance, this system must be installed as defined within this manual.

Any deviation from this renders the installer liable for any EMC problems that may occur

either to the equipment or to any other equipment affected by the installation.

The TWINFLEX®SRP System

The TWINFLEX®SRP system is a single flood zone panel with an intelligent ‘2-wire’ system utilising a

conventional type cabling format. The system is classed as ‘Analogue non-addressable’ due to the

architecture used within the design. All field devices including sounders can be connected to the zone

via a common 2-core screened cable. The devices communicate with the control panel using the

TWINFLEX®data protocol.

The TWINFLEX®SRP panel monitors each zone for detector head removal, device fault, ‘End of line’

fault and open or short circuit fault.

Devices or detector heads should not be removed with the zone switched on.

Switch off the zone (at access level 3) before removing any devices or detector

heads from that zone.

Twinflex detector heads must only be removed using the correct head removal

tool, 25-0046-201. Removing detector heads without using the correct tool will

result in damage to the head / detector base.

Every device has an inbuilt ‘End of line’ signal, which may be activated as required. All setting options

are configured using the DIL switches fitted to the device.

Do not use a resistor or capacitor or any other 3rd party ‘End of line’ module for

‘End of line’.

The TWINFLEX®SRP control panel also provides three monitored outputs that may be configured as

notification (conventional sounder) circuits or 2 notification (conventional sounder) circuits and 1

releasing circuit, four volt free common relays and a volt free common fault relay. There are also five

multifunction latching/non-latching inputs.

The TWINFLEX®SRP control panel incorporates an integral power supply unit and requires 2 x 12V

12.0Ah batteries to provide up to 72 hour standby times depending on system loading (refer to

Technical Data for further information). Standby battery calculations may be made using the

TWINFLEX®SRP Panel Battery & Loading Unit Calculation Sheet (document no. 26-1389).

Unlike most conventional fire alarm systems, which require separate pairs of cables for detector zones

and sounder circuits, the TWINFLEX®SRP system requires one 2-core screened cable for each zone

to accommodate both detection devices and sounders. Furthermore, sounders are incorporated within

the detector to reduce system components and simplify installation.

The zones can also be programmed to be conventional zones and use conventional detectors.

MCPs must not be used on conventional zones. Conventional zones cannot distinguish

between an MCP or detection activation so if needed should be connected to a monitored input.

An MCP activation will therefore not initiate an extinguishing release procedure on a conventional zone.

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

The TWINFLEX®SRP panels include some features described in EN54-2 as ‘optional functions with

requirements’. These are:-

Output to fire alarm devices EN54-2 Clause 7.8

Output to fire protection equipment, type A EN54-2 Clause 7.10.1

Delays to outputs EN54-2 Clause 7.11.1

Zone test facility EN54-2 Clause 10

Input/output facilities EN54-2 Clause 7.11.1

The TWINFLEX®SRP panel includes the following compulsory features required by EN12094-1:

Input signal to manually trigger EN12094-1 Section 4.3.2a

Transmission of extinguishing signal EN12094-1 Section 4.3.2b

Activation of alarm devices after triggering EN12094-1 Section 4.3.2c

Unambiguous indication of each condition EN12094-1 Section 4.2.2d

Transmission of incorrect status and fault warning EN12094-1 Section 4.3.2e

Transmission of the released condition EN12094-1 Section 4.3.2f

The TWINFLEX®SRP panel includes the following optional features with requirements allowed by

EN12094-1:

Delay of extinguishing signal up to 60 seconds EN12094-1 Section 4.17

Signal representing flow of extinguishing agent EN12094-1 Section 4.18

Monitoring of status by way of a low pressure switch input EN12094-1 Section 4.19

Emergency hold device to allow delay to be extended EN12094-1 Section 4.20

Control of flooding time EN12094-1 Section 4.21

Manual only mode to disable release EN12094-1 Section 4.23

Triggering of equipment outside the system EN12094-1 Section 4.26

Control of extended discharge EN12094-1 Section 4.28

Activation of alarm devices to indicate pre-discharge and release EN12094-1 Section 4.30

These facilities are described elsewhere in this manual.

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

Control Panel

Mounting the Control Panel

First identify the proposed location for the control panel. Ensure that the control panel will be easily

accessible and that account is taken of any subsequent work that may affect access.

The control panel should be located at the most likely point of access for the fire services. It should be

mounted on a flat, vertical wall at a height where the indicators may be seen without difficulty.

Do not locate the control panel at high level where stepladders or other access equipment may

be required, in spaces with restricted access, or in a position that may require access panels to

be removed.

Do not locate the control panel where extremes of temperature or humidity may occur, or where

there is any possibility of condensation or water ingress.

Like all electronic equipment, the control panel may be affected by extreme environmental conditions.

The position selected for its installation should therefore be clean and dry, not subjected to high levels

of vibration or shock and at least 2 metres away from any pager or radio transmitting equipment.

Ambient temperatures should be within the range given within the Technical Data section, e.g. not

directly over a radiator or heater.

In common with all microprocessor-controlled panels, the control panel may operate erratically or may

be damaged if subjected to lightning-induced transients. Proper earth/ground connections will greatly

reduce susceptibility to this problem.

Physical Dimensions

The control panel back box is designed as a dual-purpose surface or flush mount unit.

Surface Mounting: Utilize the three through holes in the back of the back box to secure it to the

mounting surface with suitable anchors

Flush Mounting: Cut an opening in the wall to fit the back box dimensions, not to include the 14mm

flange, and secure the box in place utilizing the through holes provided on the sides of the back box

with suitable anchors.

TWINFLEX®SRP Control Panel Engineering and Commissioning Manual

NOTE: The 14mm flange facilitates flush mounting. To allow installation of the main front moulding, this

flange must be flush with the mounting surface and not recessed into it.

Table des matières

Autres manuels Fike Panneau de contrôle

Fike

Fike FIK-5496 Manuel utilisateur

Fike

Fike SITA200plus Manuel utilisateur

Fike

Fike Quadnet Manuel utilisateur

Fike

Fike CIE-A-200 Manuel utilisateur

Fike

Fike FCP-75 Manuel utilisateur

Fike

Fike FIK-RA100BD Manuel technique

Fike

Fike FIK-RA2000 Manuel technique

Fike

Fike FCP-75 Manuel utilisateur

Fike

Fike FCP-2100ECS Manuel utilisateur

Fike

Fike Twinflex pro2 Manuel utilisateur

Fike

Fike GB2426367 Manuel utilisateur

Fike

Fike TWINFLEXpro Manuel utilisateur

Fike

Fike FCP-2100 Manuel utilisateur

Fike

Fike FCP-300 Manuel utilisateur

Fike

Fike TWINFLEXpro Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques