Field Controls 46263400 Instructions de montage

Table des matières

Autres manuels Field Controls Ventilateur

Field Controls

Field Controls 46139100 Manuel utilisateur

Field Controls

Field Controls 46255400 Manuel utilisateur

Field Controls

Field Controls 46413900 Manuel utilisateur

Field Controls

Field Controls 46456700 Manuel utilisateur

Field Controls

Field Controls 46233500 Mode d’emploi

Field Controls

Field Controls 46263500 Guide de démarrage rapide

Field Controls

Field Controls VentCool 1.8 Manuel utilisateur

Field Controls

Field Controls 46477000 Manuel utilisateur

Field Controls

Field Controls 46068600 Manuel utilisateur

Field Controls

Field Controls 206900 Manuel utilisateur

Field Controls

Field Controls 46256400 Manuel utilisateur

Field Controls

Field Controls Eliminator Manuel utilisateur

Field Controls

Field Controls VentCool Tahoe Series Manuel utilisateur

Field Controls

Field Controls PVO-600 Manuel utilisateur

Field Controls

Field Controls 46334800 Manuel utilisateur

Field Controls

Field Controls 4592700 Manuel utilisateur

Field Controls

Field Controls 46385600 Manuel utilisateur

Field Controls

Field Controls AB-1 Manuel utilisateur

Field Controls

Field Controls 2702600 Manuel utilisateur

Field Controls

Field Controls 46378300 Manuel utilisateur

Field Controls

Field Controls 46284600 Manuel utilisateur

Field Controls

Field Controls 46483500 Manuel utilisateur

Field Controls

Field Controls 46115300 Guide de l'utilisateur

Field Controls

Field Controls CK-63 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage

SPECIAL VENTING APPLICATION

INSTALLATION SHEET FOR

AQUAHUT® WATER HEATER ENCLOSURES

This sheet covers the requirements for installing the Star-Kap™ on an Aquahut®gas water heater

enclosure. The Aquahut®enclosure is designed for the purpose of housing agas water heater

outside of the living space of a structure. These requirements are based on the A.G.A. test reports

C-FT-5-90, C-FT-8-90, FT-C-12-93, FT-C-13-93, FT-C-14-92 and the SBCCI letter dated May 24,

1990. The Aquahut®water heater enclosure is not sold or manufactured by the Field Controls Co.

These installation instructions only address the installation of the Star-Kap™, state the maximum

capacity water heater allowed in an Aquahut®and the vent termination clearances from windows or

openings into a building structure as tested in the A.G.A. field reports C-FT-5-90, C-FT-8-90, FT-C-

12-93, FT-C-13-93, FT-C-14-92 and the SBCCI letter dated May 24, 1990.

INSTALLATION GUIDE LINES

1. The maximum gas water heater appliance to be operated in a Aquahut®enclosure: up to 90,000

BTU/HR input.

2. Two (2) make up/combustion air openings into the Aquahut®enclosure shall be installed. Each

opening size shall be based on one (1) square inch per 4000 BTU/HR. The vent termination shall

have the following clearance distances.

a. AH40 Model Aquahut®

14” from combustible exterior wall to center of vent cap

b. AH50 Model Aquahut®

16” from combustible exterior wall to center of vent cap

c. A minimum of 12” from any window or opening into the main building structure

d. A minimum of 18” below an eave or overhang

STAR-KAP™ INSTALLATION

1. Before installation, apply two (2) beads of high

temperature silicone sealant or equivalent around

the bottom of the storm collar and one (1) inch

above the end of the Star-Kap™ body. (See

Figure 1)

2. Insert the Star-Kap™ into the inside of the single

wall vent pipe, making sure the Star-Kap™ is

seated against the storm collar. Fasten the Star-

Kap™ to the single wall vent pipe, by using

three (3) sheet metal screws. Placement of the

screws should be approximately 1/2 inch from

the end of the single wall vent pipe. The heads

of the screws should be covered with high

temperature silicone or equivalent.

Figure 1

P/N 46263400 Rev D 11/00