FibreHead FH-4WH Manuel utilisateur

Hardware

Included

Tools Required

Not Included

FH-4WH

Flush mount wheel hangers set

Thank you for purchasing our Flush mounted wheel hangers.

This product is intended for storage of wheels with tires weighing up to 120lbs each.

Please read these instructions from start to finish before beginning.

-We are not liable for damages caused by improper installation or misuse of this product.

-Not recommended for Seismic zones 3 or higher.

-Always check/detect routing of pipes and electrical before penetrating/drilling walls.

-Clear the installation space of vehicles or valuables before beginning.

Drywall with Wood Studs Masonry (concrete/brick)

1 /2”

Socket + Ratchet Tape Measure Drill

3 /16” Drill bit

1 /2” Drill bit

Stud Finder

Hammer

(8x) Lag Bolts (8x) Lag Shield (8x) Bolt caps

Parts

Included

Safety Glasses

Common

Pencil

Drill

Stud Finder

Wood stud with drywall Install

Skip to next section installing into Masonry (Block or Brick)

Safety Glasses

Step 1. Locate and Mark Studs

Pencil Measure

to match

Height

Step 2. Pre-drill Bolt locations

3 /16” Drill bit

1. Center top hanger hole over the marked locations and drill 3”

deep.

2. Repeat this for all 8 holes using the hanger as a template.

( you should see wood dust come out with the drill bit).

Step 3. Fasten bolts and test weight

Note:

For oversize tires

32” and larger.

Instead of a

straight line,

do a zigzag pattern

offsetting for

additional size.

1 /2”

Socket + Ratchet

1.Fasten all 8 Bolts using a ratchet.

2.Test each Hanger by pulling it up and down

with one arm to make sure its securely in the

stud.

3. Press plastic Caps over each Bolt Head

(to protects your wheels from scratching)

Stud

Drill or Hammer drill

Masonry Install

Installing in Concrete, Block or Brick.

Safety Glasses

Pencil

32” Apart

Measure

to match

Height

Step 2. Drill Lag Shield locations

1. On center Mark, use a ½” Drill bit and drill 2.5 to 3” deep.

2. Repeat this for all 8 holes

3.Insert Lag Shields ( “Hole” label side first) Tap with Hammer into

place.

Step 3. Fasten bolts and test weight

Note:

For oversize tires

32” and larger.

Instead of a

straight line,

do a zigzag pattern

offsetting for

additional size.

1 /2”

Socket + Ratchet

1.Fasten all 8 Bolts using a ratchet.

2.Test each Hanger by pulling it up and down

with one arm to make sure its securely in the

wall.

3. Press plastic Caps over each Bolt Head

(to protects your wheels from scratching)

Use Hanger

As a Hole

Template

1 /2” Drill bit

“Hole”

label

Step 1. Locate and Mark Studs

(Hole center accuracy required so be precise)

Hammer

Hanging Wheels

F.A.Q.

Q: What if my wheels don’t have a center hub opening. (Some Corvettes)

A: Cover the hanger with the plastic bag it came in so it doesn’t scratch your rims.

Hang the rim through one of its wedge openings , resting at the top.

Q. My Wall has steel studs. Can I still use the Hangers?

A: Follow same instructions as wood stud wall but Reduce the weight capacity to 50lbs

Q. My wheels and tires are too big and don’t fit at the 32” spacing.

A: You must hang every other hanger lower (Zigzag pattern). Spacing will depend on wheel size.

Cutaway view

shown.

Always hang the

wheel face closest

to the wall

Step 4. Remove center cap and

Hang wheels

X Incorrect X Correct

Finished!

Great job…Time for a beverage.

Do you like our product ?

It would mean a lot if you could leave a review at

where you purchased it.

Thank you.

Autres manuels FibreHead Support et étagère

FibreHead

FibreHead FH-TRI Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur