Festool VS-600 Manuel

Page 1 of 5 www.festool-usa.com

VS600 Jointing System — Procedure for Half Blind Dovetails

A Step by Step Procedure for these templates: SZ14 and SZ20

Template SZ14 - Half Blind Dovetail

for wood thickness .63 - .79" (26-20mm)*

Cutters: 490 991 (HSS); 490 990 (carbide)

Template SZ20 - Half Blind Dovetail

for wood thickness .63 - .79" (26-20mm)*

Cutters: 490 991 (HSS); 490 990 (carbide)

* wood thickness measurements refer to front/back

piece only - sides can be thinner.

Install the copying ring. The ring should be the

one that came with the SZ14 or SZ20

template or one that fits in the template

grooves exactly.

Install the appropriate bit in the router.

Cutters: 490 991 (HSS)

490 990 (carbide)

Page 2 of 5 www.festool-usa.com

Install SZ14 Template. Before tightening

locking knobs, be sure the alignment shoulders

on underside are touching the base.

Rotate end stops so that SZ14 is pointing to

wood edge.

I lower the template and adjust the two black

positioners so they are in the "D" window.

I move the black positioner left and right until

the arrows are touching the flat side of the "D"

and lock it in that place.

Page 3 of 5 www.festool-usa.com

This is the drawing from the Manual. You

should mark the pieces of your box

accordingly.

I have laid out the test drawer and have

numbered everything the exact same way.

Position the front/back piece in the horizontal

clamp with insides facing up. The "A"

corners will be on the left; the "B" on the right.

Position the sidepiece with the inside edge

facing front and touching the underside of the

template.

Make sure the front/back piece is touching the

backside of the sidepiece end.

Page 4 of 5 www.festool-usa.com

Zero router by placing it on the template and

plunge the bit until it "kisses" the top of the

wood. Lock the plunge.

Move the plunge rod to the 12mm position.

This is the recommended start depth for use

with this template.

I move the router over where it is still on the

template but no wood is beneath. I plunge to

the preset point and lock the plunge setting.

I also adjust the dust hood so that it allows

free movement of the router on the template

— including room to cut the tails.

Page 5 of 5 www.festool-usa.com

It doesn't take long to run the router for both

the "A" and "B" joints. I have made a very

light pass from right to left (climb cut) — this

will reduce tear out. Then, guide the router

into each of the fingers.

Test fit the pieces. They are exact. I did spray

paint the "A" front side for a contrast —

otherwise, these photos are unretouched.

This template can do great drawers. At the

right, the front joint is with 3/4" front and 3/4"

sides. Since many cabinets have drawers with

1/2" sides and 3/4" fronts, the upper example

is just that and did not require any change to

the set-up.

It can even do 1/2-blind dovetails with a

rabbet front.

Autres manuels pour VS-600

Table des matières

Autres manuels Festool Outils électriques

Festool

Festool Carvex PSC 400 EB Manuel utilisateur

Festool

Festool KA 65 Manuel utilisateur

Festool

Festool Domino DF 500 Q Manuel utilisateur

Festool

Festool ETS EC 150/3 A EQ Instructions d'installation

Festool

Festool ETS EC 125/3 EQ Manuel utilisateur

Festool

Festool Trion PS 300 EQ Manuel utilisateur

Festool

Festool MFK 700 EQ Manuel utilisateur

Festool

Festool Carvex PS 420 EBQ Manuel utilisateur

Festool

Festool OFK 500 Q Manuel utilisateur

Festool

Festool Domino Machine Manuel utilisateur

Festool

Festool PF 1200 E Instructions d'installation

Festool

Festool Duplex LS 130 EQ Manuel

Festool

Festool LEX 2 150/3 Manuel utilisateur

Festool

Festool Trion PS-300Q Manuel utilisateur

Festool

Festool DX 93 E Manuel utilisateur

Festool

Festool Carvex PSC 400 EB Manuel utilisateur

Festool

Festool OFK 700 EQ Manuel utilisateur

Festool

Festool KA 65 Manuel utilisateur

Festool

Festool ROTEX RO 90 DX FEQ Manuel utilisateur

Festool

Festool Carvex PS 420 EBQ Manuel utilisateur

Festool

Festool BG-RG 150 Instructions d'installation

Festool

Festool HKC 55 EB Manuel utilisateur

Festool

Festool Trion PS-300Q Instructions d'installation

Festool

Festool VS-600 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel