Festool KF 5 EBQ Manuel utilisateur

1/3

508/01

Description

This application example describes how to cut out weather-beaten linseed

oil putty beds with the putty router KF 5 EBQ.

The renovation of painted windows not only requires new paint. The best coat

is useless if the linseed oil putty bed is cracked or partly destroyed. Rain and

condensation can then get under the new coat, causing it to flake and exposing

the wood.

No. 508

Cutting putty beds

2/4

The Festool putty router KF 5 EBQ and corresponding groove cutter HW

D10/30, HW D12/30 or HW D16/30 (depending on the putty bed width) can be

used to remove linseed oil putty on the glass pane easily and efficiently.

Denomination Order no.

Putty router KF 5 EBQ-Plus GB 240V 574 290

Side stop SA-OF 1010 489 427

Fine adjustment FE-FS / OF 1000 499 754

Groove cutter HW dia. 10 mm, NL 30 mm 491 648

Groove cutter HW dia. 12 mm, NL 30 mm 491 649

Groove cutter HW dia. 16 mm, NL 30 mm 490 967

Mobile dust extractor from the CTL or CTM series

Tools/accessories

Basic equipment:

508/02

508/04

508/03

Preparation/set-up

Preparing the putty router:

Place window sash securely in position and clamp it.•

Fit the router bit in the putty router (cutter diameter - see above -•

depends on the putty bed width: dia. 10 mm, dia.12 mm, dia. 16 mm)

Set the speed to level 6.•

Mount the putty router on the window sash.•

Place the support (1) on the glass and tighten with the rotary knob (2)•

(see Fig. 508/5).

Place a piece of cardboard under the cutter onto the glass to ensure the•

glass is a safe distance away during cutting.

Move the putty router with the cutter until the cutter is on the cardboard.•

Move the stop of the routing depth setting against one of the three turret•

stops.

Connect the extractor hose to the tabletop of the KF 5.•

508/05

Important:

Use protective goggles and gloves!

3/4

Our application examples are recommendations which have been tried and tested in

practice. However the different conditions are completely outside of our control. We

therefore do not provide any form of guarantee. Any legal claims arising out of this are

not to be made against Festool. Make sure you follow the safety directions and product

instructions provided with the product.

www.festool.co.uk

508/06

Setting the routing width:

Mount side stop with fine adjustment on tabletop.•

Push side stop against window sash.•

Make the rough adjustment of the cutter position using the linkage of the•

side stop.

Set the side stop with the fine adjustment (see Fig. 508/6) so that the•

cutter cleanly cuts out the putty in the glazing rebate.

Tip: On old windows, the wood can be recut until a straight putty rebate

edge guarantees perfect sealing.

508/07

508/08

Procedure

Switch on machine and plunge in. When routing, ensure that the side•

stop always makes contact with the window sash (see Fig. 508/7) and the

machine is flat on the surface of the window sash.

In order to cut right into the corner, in the area of the crossbar the•

chip protection is pulled upwards until it disappears in the router table

(see Fig. 508/8).

Always route in reverse direction to ensure to the longest possible•

service life of the cutters.

Windows with weatherboards at front

In order to cut right into the corner on windows with weatherboards, a

wooden base as high as the weatherboard must be fitted on the left and

right of the upright sash (see Fig. 508/9). Chip flutes are cut out at the

wooden bases to ensure that the fastening clamps do not obstruct the side

stop of the putty router (see Fig. 508/10). With this device, the putty can be

cut out comfortably and reliably from the two sashes and the weatherboard.

Upon completion of this work, corner areas can be reworked if necessary

with the firmer chisel and new putty can be applied.

508/9

508/10

Autres manuels pour KF 5 EBQ

Table des matières

Autres manuels Festool Outils électriques

Festool

Festool OF 2200 EB-F Manuel utilisateur

Festool

Festool OFK 500 Q Manuel utilisateur

Festool

Festool KF 5 EBQ Manuel utilisateur

Festool

Festool MFK 700 EQ Manuel utilisateur

Festool

Festool PSC 420 EB Instructions d'installation

Festool

Festool RAS 180.03 E-HR Manuel utilisateur

Festool

Festool VS-600 Manuel utilisateur

Festool

Festool OFK 700 EQ Manuel utilisateur

Festool

Festool Trion PS 300 EQ Manuel utilisateur

Festool

Festool Carvex PS 420 EBQ Instructions d'installation

Festool

Festool Duplex LS 130 EQ Manuel

Festool

Festool Basis KA 100 Manuel utilisateur

Festool

Festool Trion PS-300Q Instructions d'installation

Festool

Festool MFK 700 EQ Instructions d'installation

Festool

Festool OF 1400 EBQ Manuel utilisateur

Festool

Festool OF 2200 EB Manuel utilisateur

Festool

Festool CARVEX PSBC 420 Instructions d'installation

Festool

Festool AH-ES-ETS Manuel utilisateur

Festool

Festool Precisio CS 50 EB Manuel utilisateur

Festool

Festool MFK 700 EQ Manuel utilisateur

Festool

Festool Carvex PS 420 EBQ Manuel utilisateur

Festool

Festool VECTURO OS 400 EQ Instructions d'installation

Festool

Festool Domino XL DF 700 EQ Instructions d'installation

Festool

Festool TDK 12 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel