Fenix TK65R Manuel utilisateur
Fenix TK65R Flashlight
1. Catapult action belt clip
2. Quick-release button
Technical Parameters
ANSI/PLATO
FL1
General Mode
Flash Mode
Turbo
High
Med
Low
Eco
Strobe
SOS
Output
3,200
Lumens
1,000
Lumens
400
Lumens
150
Lumens
30
Lumens
3,200
Lumens
400
Lumens
Runtime
1h 45min
4h 55min
13h
10min
35h 45min
113h
/
/
Distance
375m
218m
138m
83m
37m
/
/
Intensity
35,155
cd
11,880
cd
4,760
cd
1,720
cd
340 cd
/
/
Impact
Resistance
1m
Waterproof
IP68, underwater 2m
Note: The abovementioned parameters (lab-tested by Fenix using 7.2V/5000mAh Li-ion battery
pack) may vary between flashlights, batteries and environments.
Cree XHP70 LED with a lifespan of 50,000 hours
Built-in 7.2V/5000mAh Li-ion battery pack
Micro USB fast charging with fast charging adaptor
Micro USB charging port with inner waterproofing design
270.5mm Length x 61.5mm Head diameter x 36.5mm Body diameter
418g (excluding battery and belt clip)
Dedicated catapult action belt clip
Digitally regulated output maintains constant brightness
Featuring battery level indication and low-voltage warning function
Intelligent overheat protection protects from high surface temperature
Made of durable aircraft-grade aluminum; stainless steel strike bezel
Premium type III hard-anodized anti-abrasive finish
Toughened ultra-clear glass lens with an anti-reflective coating
Accessories:
7.2V/5000mAh Li-ion battery pack
Spare O-ring
Micro USB charging cable
USB adaptor
Catapult action belt clip
Operation
Switches
①Master switch: controls on/off and output selection in General mode
②Auxiliary switch: controls on/off and output selection in Flash mode
ON: With the light switched off, press and hold the Master switch for 0.5 seconds to enter
General mode, press and hold the auxiliary switch for 0.5 seconds to enter Flash mode.
OFF: With the light switched on, press and hold either the master or auxiliary switch to turn off
the light.
Mode Selection
In General mode, single click the auxiliary switch to change to Flash mode.
In Flash mode, single click the master switch to change to General mode.
Output selection
In General mode, single click the master switch to cycle through Eco→Low→Med→High→Turbo.
In Flash mode, single click the auxiliary switch to cycle through Strobe→SOS.
③Lock-out Function
Lock: with the light unlocked, simultaneously press and hold the two switches for over 3 seconds.
Light will switch off and 2 one-second blinks will indicate locked status.
Unlock: with the light locked, simultaneously press and hold the two switches for over 3 seconds.
The light will be unlocked and activated on last used brightness.
In locked status, pressing any switch will activate 2 one-second blinks to indicate locked status.
Intelligent Memory Circuit
The light memorizes the last selected brightness level on General mode. When turned on again
the previously used brightness level will be recalled.
Intelligent Overheat Protection
The light will accumulate a lot of heat when used on Turbo output level for extended periods.
When a temperature of 65°C or above is reached, the light will automatically step down by a few
lumens to reduce temperature. When the temperature is reduced, the output will gradually
return to Turbo output level.
④Battery Level Indication
There are four LED’s in the light tail. Single clicking the round switch on the tail will indicate
remaining battery level for 3 seconds:
The more LED’s light up, the higher the battery level.
Four LED’s on: more than 80%;
Only one LED on: more than 20%
One LED flashing: less than 20%
Low-voltage Warning
When the voltage level drops below the preset level, the flashlight is programmed to downshift
to a lower brightness level until Eco output is reached. When this happens in Eco output mode,
the flashlight blinks three times every five minutes to remind you to replace the battery. To
ensure normal use, the flashlight will only turn off once the battery over-discharging protection
activates.
⑤Charging
First plug the USB terminal of the charging cable into an electrical outlet, then connect the Micro
USB terminal of the charging cable to the light. The LED indicators will flash in sequence while
charging, and will turn to constant on when fully charged. The normal charging time is
approximately 4 hours.
Note:
1. Once charging is completed, be sure to close the anti-dust cover.
2. Recharge a stored light every four months to maintain optimum performance of the battery.
⑥Battery Replacement
Unscrew the tail cap to insert the battery (no need to check the polarity), then screw the tail
cap back on. Remove the insulation sheet before first use.
Usage and Maintenance
Disassembling the sealed head can cause damage to the light and will void the warranty.
Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring
with an approved spare．
Periodic cleaning of the battery contacts improves the lamp's performance as dirty contacts
may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following
reasons:
A: The batteries need replacing.
Solution: Replace batteries (Ensure batteries are inserted according to the manufacturer’s
specifications).
B: The threads, PCB board contact or other contacts are dirty.
Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol.
If the above methods don't work, please contact your authorized distributor.
Warning
This flashlight is a high-intensity lighting device capable of causing eye damage to the user or
others. Avoid shining the flashlight directly into anyone’s eyes.
Table des matières
Autres manuels Fenix Lampe de poche
Fenix
Fenix E05R Manuel utilisateur
Fenix
Fenix E-SPARK Manuel utilisateur
Fenix
Fenix TK72R Manuel utilisateur
Fenix
Fenix LD15R Manuel utilisateur
Fenix
Fenix TK40 Manuel utilisateur
Fenix
Fenix E25 Manuel utilisateur
Fenix
Fenix LR40R Dimensions
Fenix
Fenix TK32 Manuel utilisateur
Fenix
Fenix LD32 UVC Manuel utilisateur
Fenix
Fenix WT16R Mode d'emploi
Fenix
Fenix E LITE Manuel utilisateur
Fenix
Fenix RC09 Manuel utilisateur
Fenix
Fenix TK12 Manuel utilisateur
Fenix
Fenix TK22 TAC Manuel utilisateur
Fenix
Fenix TK40 Manuel utilisateur
Fenix
Fenix LR40R Manuel utilisateur
Fenix
Fenix LD22 Manuel utilisateur
Fenix
Fenix LD03 Manuel utilisateur
Fenix
Fenix TK26R Manuel utilisateur
Fenix
Fenix HL30 Manuel utilisateur
