Fein AFMM 18 Manuel utilisateur
AFMM 18; AFMM 18QSL
Technical data
C-SC_CSSM
Version 1.0
2016-04-06
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Technical data
All the technical data can be found in the operating instructions for the model.
Tests
Up-to-date test data and test instructions after repair can be found on the FEIN Extranet (Customer Service → Repair Guides).
Lubricants / Auxiliary substances
The lubricants or auxiliary substances and their container sizes available from FEIN can be found on the FEIN Extranet
(Customer Service → Repair Guides).
Lists of spare parts
Lists of spare parts and exploded views are available online at www.fein.com
AFMM 18; AFMM 18QSL
Notes and requirements
C-SC_CSSM
Version 1.0
2016-04-06
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Please note
These instructions are only intended for persons with suitable technical training. It is assumed that the reader has mechanical and
electrical training.
Only use original FEIN spare parts.
Provisions
Please note that power tools may only be repaired, maintained and checked by a trained electrician, as improper repair can result in
serious risks to the user.
The provisions set out in DIN VDE 0701-0702 should be observed after repairs.
The relevant accident prevention regulations of the employer’s liability insurance associations are to be observed when
commissioning.
The German Equipment and Product Safety Act [ProdSG] applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed.
AFMM 18; AFMM 18QSL
Lubricants and auxiliary substances required
C-SC_CSSM
Version 1.0
2016-04-06
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Lubricants
Grease 0 40 101 0100 4 10 g Tool Head
AFMM 18; AFMM 18QSL
Troubleshooting
C-SC_CSSM
Version 1.0
2016-02-11
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
If the grooved ball bearing is faulty, check whether the compensating
washer to the eccentric part has twisted.
Replace the motor if the compensating washer to the eccentric
part is twisted.
AFMM 18; AFMM 18QSL
Removal
C-SC_CSSM
Version 1.0
2016-02-11
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 8
Removing the motor housing
1. Cut through the type plate.
2. Unscrew the seven screws (1).
3. Remove the motor housing (2).
4. Remove the pressure piece (3).
Tools:
- Blade
- Torx T15
1
2
3
AFMM 18; AFMM 18QSL
Removal
C-SC_CSSM
Version 1.0
2016-02-11
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 2of 8
Removing the motor housing
1. Remove the slide switch (1).
2. Remove the locking spring (2).
3. Remove the tool head, the motor and the electronics from the motor housing.
2
1
AFMM 18; AFMM 18QSL
Removal
C-SC_CSSM
Version 1.0
2016-02-11
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 3of 8
Removing the pressure pieces
1. Remove the four pressure pieces (1).
1
AFMM 18; AFMM 18QSL
Removal
C-SC_CSSM
Version 1.0
2016-02-11
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 4of 8
Removing the motor
1. Unsolder the cables (1). Tools:
- Soldering station
1
AFMM 18; AFMM 18QSL
Removal
C-SC_CSSM
Version 1.0
2016-02-11
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 5of 8
Removing the motor
1. Remove the four pressure pieces (1) [on both sides].
2. Unscrew the four screws (2).
3. Turn the motor (3) to the right.
Tools:
- Torx T20
1
3
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fein Outils électriques
Fein
Fein QSz 636-1 Manuel utilisateur
Fein
Fein ABLS18-1.6 E Series Manuel utilisateur
Fein
Fein ASye 636 Kinetik Manuel utilisateur
Fein
Fein KFH17-8 Series Manuel utilisateur
Fein
Fein ABLS18-1.6E Manuel utilisateur
Fein
Fein FSC1.6X Manuel utilisateur
Fein
Fein SCT5-40X Manuel utilisateur
Fein
Fein ASW 10-6-2ST Manuel utilisateur
Fein
Fein KFH17-8 Series Manuel utilisateur
Fein
Fein AMM 500 Plus Manuel utilisateur
Fein
Fein KS10-38E Manuel utilisateur
Fein
Fein SCW 16-6 Manuel utilisateur
Fein
Fein ALG30 Manuel utilisateur
Fein
Fein BSS 2.0 E Guide de configuration
Fein
Fein BLK1.3TE Guide de configuration
Fein
Fein ABLK1.3TE Manuel utilisateur
Fein
Fein BSS 1.6 Manuel utilisateur
Fein
Fein ASg 636 Manuel utilisateur
Fein
Fein AMM 500 Plu Manuel utilisateur
Fein
Fein FMT250Q Manuel utilisateur
