FAVI FPM1949LT3W Manuel utilisateur
Model: FPM1949LT3W
• Be sure to read this manual thoroughly before installing.
• Sufficient expertise is required for installing this projector wall mount.
• Do not use the projector wall mount for other purposes than what it is designed for.
• Keep this manual available for future reference.
IMPORTANT SAFTY NOTES
1. Be sure to read this manual thoroughly before installing projector wall mount.
2. Only qualified technicians (two or more) should install or dismount the projector from the wall mount.
3. For safety reasons, check the strength of the wall before installation. If wall is not strong enough to hold wall mount
and projector weight, do not install until wall is properly reinforced for installation.
4. Wall mount should only be installed on a flat surface.
5. Do not install the wall mount to a wall subjected to vibration or impact.
6. To avoid fire, do not install projector with the wall mount in a humid or excessively dusty environment.
7. Only use the supplied accessories to assemble and install the wall mount. Use of accessories other than those supplied
may result in damage to the projector wall mount.
8. Unplug the projector power cable and all other connecting cables before dismounting the projector from the wall mount.
9. Do not hit or hang heavy objects on the wall mount other than one projector unit. If the wall mount is damaged, stop
use and contact a qualified technicians immediately to dismount the projector and wall projector.
10. Do not alter the wall mount. Altering wall mount may result in damage to the mount, cause safety hazards, and will
void any warranty.
Wall Mount Weight Capacity: < 22 lb.
Use with products heavier than the weight capacity may result in instability that may lead to possible injury.
Manufacturer is not liable for any damages and injury caused by mishandling or improper installation of mount.
ACCESSORIES
Fixed Support Arm (1) Projector Mounting Plate (1) Wall Plate Cover (1)
Wall Plate (1) Wall Cover (1)
NO Image Description Quantity
A Screw (M6 x 55) 5
B
Φ
10mm Anchor bolt 5
C L5 Allen Key 1
D L3 Allen Key 1
E Screw (M4 x 8) 4
F Screw (M6 x 15) 4 1
Mounting on concrete ceiling:
Ensure wall is a minimum of 4-inches in thickness.
Use anchor bolts (B) and screws (M6 x 55, A) for
installation.
Mounting on dry-ceiling:
Ensure wall is a minimum of 4.5-inches in thickness.
Use screws (M6 x 55) for installation. If the wall is
not strong enough for installation, reinforce it before
installing.
INSTALLING WALL MOUNT
Φ
10 ~ 11 mm
Φ
3 mm
Use anchor bolts.
*Anchor bolts are
not necessary.
2 in
2 in
2
Place with
arrows up
Take off cap
Loosen screws
Cables
Place with
arrows up
Wooden Stud
Center Line
CAUTION:
When installing on dry
wall with wood stud,
ensure wall mount is
center align with the
wood stud.
Loosen the screws with L3 allen
key, pull out the support arm
around 4-inches and feed power
cable and other cables through
the support arm.
INSTALLING WALL MOUNT (Cont.)
Cables
Cables
METHOD 1
METHOD 2
METHOD 3
Cables
Cables can be feed through
wall plate in the three methods
shown to the left. Once cables
are secure, fasten the screws.
Tighten screws Connect power cable and other cables to projector.
ATTACH PROJECTOR TO MOUNT
3
Move the projector mounting plate left or right to decide the projector position.
Adjust left or right
sliding distance
Screen adjustment direction
4
ADJUST SUPPORT ARM
NOTE: When the 22-in length of the inside arm does not meet your demand, you should loosen the screws
from the outside arm to adjust the middle arm.
ADJUST PROJECTOR HEIGHT
ADJUST VERTICAL TILT KNOB
Check the scale to see the distance
from wall to mounting plate.
Adjustment
direction
Adjustment
direction
Adjustment direction
Adjustment knob
5
ADJUST HORIZONTAL ROLL KNOB
ADJUST HORIZONTAL ROTATION KNOB
PUT ON DECORATIVE COVER
NOTE: The wall plate covers can be used to cover the empty area. The number of plate covers to use vary
on the size of the empty area. The plate covers must be used in the specific order as shown above. Once
plate covers are in place, put the wall cover on.
PRODUCT INFORMATION
Model: FPM1949LT3W
Net Weight: 11-lb
Load Capacity: 33-lb
Adjustment Range: 12.8 to 29-in
Adjustment Angle: ± 5otilt, left/right, front/rear, and lateral rotation adjustment
Adjustment direction
Adjustment knob
Adjustment knob
Wall plate cover
OR
Adjustment direction
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels FAVI Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
