Fantini Cosmi CH130RFR Manuel utilisateur

CH130RFR

RADIO FREQUENCY AMBIENT THERMOSTAT

FOR FAN-COILS

Inserting and replacing the batteries .................9

CH172DRF self-learning procedure ..................9

Thermostat conﬁguration .................................10

Technical features of the thermostat ......................13

DIN bar CH172DRF actuator .................................13

Application and use .........................................13

Fastening and connecting ...............................14

Operation .........................................................14

Operation check ..............................................15

Technical features of the actuator ..........................16

TABLE OF CONTENTS

Introduction ..............................................................3

Controls and signals ................................................4

Controls .............................................................4

Signals ...............................................................4

User’s manual .........................................................5

“Summer / Winter” selection ..............................5

Operating modes ...............................................6

“Comfort” operating mode .................................6

“Economy” operating mode ...............................6

“OFF” function (OFF) .........................................7

Fan speed selection ..........................................7

Maintenance ............................................................7

Installation ...............................................................7

Fastening the socket .........................................8

Electric connections ..........................................8

Fastening the thermostat onto the socket .........9

Introduction

This fan-coil thermostat control kit CH130RFR

is made up of a CH130RF thermostat and a

DIN bar CH172DRF actuator.

The CH130RF model is a fan-coil 4- or 2-pipe

thermostat that allows you to control the ambi-

ent temperature both in the heating and cooling

mode. These controls are sent to a CH172DRF

actuator that communicates with the CH130RF

through radio frequencies.

The CH130RF is powered by two AA-size bat-

teries (1.5 V). It is able to drive two valves and

control a 3-speed fan-coil motor, in manual

mode.

The thermostat measures the ambient tem-

perature either through an internal probe or an

external sensor. It keeps the set-point by act-

ing on the ventilation speed.

The wide display shows the measured tem-

perature, the fan speed, the program being run

and the selected season.

The settings and data are stored in a perma-

nent memory capable of keeping the same

even when the batteries are not inserted.

Signals

1 2 3 4 5 7 8

1. Measured temperature

2. “Comfort” symbol

3. “Economy” symbol

4. “Summer” symbol

5. “Winter” symbol

6. Fan speed symbols

7. System “ON” in summer operation

8. System “ON” in winter operation

9. Low battery charge

Controls and signals

Controls

1. Fan speed increase button

2. Fan speed decrease button

3. Selected program temperature value

increase button

4. Selected program temperature value

decrease button

5. Thermostat reset button

Button combinations (press simultan.)

1+2 Summer/Winter switch

3+4 Comfort/Economy switch

2+4 Celsius/Fahreneit switch

User’s manual

First of all, make sure that the self-learning

procedure has already been performed (page

8); moreover, verify that both the CH130 and

the CH172D are 30 metres far from each other

at the most. In fact, this distance represents

the free air maximum range for the radio fre-

quency modules used by the thermostat and

the actuator. Please note that the range will

decrease if obstacles are found between the

CH130RF and the CH172DRF.

To start the thermostat after the same has

been installed, proceed as follows:

1. Select the Summer / Winter operation;

2. Select the operating mode;

3. Select the fan speed.

“Summer / Winter” selection

To switch from the “Winter” operation (i.e. heat-

ing system) to the “Summer” operation (i.e.

cooling system), and vice versa, press the 1+2

button combination. The selected operation

will be indicated on the display by the “Winter”

or “Summer” icons.

Winter Summer

TOP COVER

THERMOSTAT

FRONT

“Economy” operating mode

With the “Economy” operating mode, the ther-

mostat regulates the heating or cooling system

operation in order to always keep the same

economy temperature set. To switch from

“Comfort” to “Economy”, press buttons “3” and

“4” simultaneously.

The temperature level can be modiﬁed during

operation by means of buttons “3” and “4”. The

temperature can be changed from 2°C to 40°C

by 0.1°C steps.

Operating modes

The CH130RF thermostat features three dif-

ferent manual operating modes: “Comfort”,

“Economy”, and the “OFF” function (OFF).

“Comfort” operating mode

With the “Comfort” operating mode, the ther-

mostat regulates the heating or cooling sys-

tem operation in order to always keep the

same comfort temperature set. To switch from

“Economy” to “Comfort”, press buttons “3” and

“4” simultaneously.

The temperature level can be modiﬁed during

operation by means of buttons “3” and “4”. The

temperature can be changed from 2°C to 40°C

by 0.1°C steps.

“OFF” function (OFF)

The “OFF” function can be achieved by setting

the fan speed to zero: in this case, the thermo-

stat will carry out no heat regulation, not even

the antifreeze one.

The system will switch off automatically, and

the “OFF” message will appear on the display.

Fan speed selection

The fan speed can be set either to three ﬁxed

levels (minimum, medium, maximum) by

pressing buttons “1” and “2”.

Maintenance

The thermostat should be cleaned by using

a soft cotton cloth. No detergent should be

used.

Installation

The thermostat installation involves carrying

out the following operations:

• Fastening the socket;

• Making the electric connections;

• Fastening the thermostat onto the socket;

• Inserting and replacing the batteries;

• Conﬁguring the thermostat parameters.

Warning! The thermostat shall be installed only

by qualiﬁed personnel, in strict compliance with

the law regulations in force.

Fastening the socket

The thermostat is supplied complete with a

socket suitable for mounting both on the wall

and to rectangular or round built-in 3-seat

boxes (503).

Remove the thermostat top cover.

Separate the thermostat socket and front by

removing the screw by means of a suitable tool

and taking the front part off.

Fasten the socket to the desired surface by

means of the special fastening holes; make

sure that the socket is properly engaged, with

no deformation, and that the connecting multi-

pole connector is located in the right bottom

DRILLING CENTERS

BATTERY

COMPARTMENT

SCREWS

SOCKET

FASTENING

HOLES

MULTI-POLE

CONNECTOR

corner.

To ensure correct operation, the socket shall

be placed at a height of approximately 1.5 me-

tres from the ﬂoor, far from heat sources (direct

sunlight, etc.) and doors/windows.

Electric connections

External probe connection

Connect the two external probe wires with

screwed terminals “1” and “2”, as illustrated in

the ﬁgure. Such probe can be conﬁgured as

external probe or minimum temperature con-

tact. See the “thermostat conﬁguration” para-

graph, P02 parameter.

60.083

range is approximately 30 metres in the free

air).

To perform self-learning, proceed as follows:

keep the CH172DRF button depressed for

at least 5 seconds, until the multicolour LED

comes on by switching among green, yellow,

red and OFF. Then press the CH130RF reset

button: after a few instants, the LED will be

blinking fast and then illuminate green steadily,

to indicate that the self-learning has occurred

(this procedure is also described in the CH172-

DRF instruction sheet).

N.B. You can also control two or several

CH172DRF actuators by means of one single

CH130RF: of course, the self-learning proce-

dure shall be performed on all the CH172DRFs

(it shall not necessarily be performed at the

same time).

Fastening the thermostat onto the socket

Insert and screw the thermostat down to the

socket (make sure that the multi-pole connec-

tor is engaged correctly).

Inserting and replacing the batteries

Insert two “AA” batteries (1.5 V) into the battery

compartment, according to the correct polarity:

the negative pole shall press the metal spring

(located on the right, when viewing the ther-

mostat from the front). Fit the battery top cover

back into place.

A pair of new batteries will normally last one

year at least. WHEN THE “low battery charge”

SYMBOL APPEARS ON THE DISPLAY, BOTH

BATTERIES SHALL BE REPLACED.

CH172DRF self-learning procedure

In order for the CH130RF and the CH172DRF

to be able to communicate correctly, a “self-

learning” procedure shall be performed. During

this procedure, the remote actuator will recog-

nize and store the CH130RF identity: from now

on, it will be able to perform all of its controls

while leaving out the controls from other trans-

mitters that might be found in the area (please

note that the CH130RF/CH172DRF system

Thermostat conﬁguration

The thermostat conﬁguration allows you to

customize the device operation parameters.

To access the conﬁguration program, proceed

as follows:

1. Press the “Reset” button and also button “3”

(with the thermostat ON);

2. Release the “Reset” button, then keep but-

ton “3” depressed for at least 3 seconds.

3. Release button “3”.

The conﬁguration parameters are represented

by an index (P01, P02…) on the display; by

pressing buttons “1” and “2”, the parameter in-

dexes will be scrolled through. Press button “3”

to enter the displayed parameter.

To modify the current parameter, press buttons

“1” and “2”. To exit the parameter, press but-

ton “3”.

Once all parameters have been set, press

button “1” until the “END” message appears,

then press button “3”. Now the thermostat will

save the modiﬁed parameters into the internal

memory and will automatically exit the param-

eter menu.

On the contrary, if buttons “1” and “4” are

pressed simultaneously when the “END” mes-

sage is displayed, the CH130RF’s RF address

will be reset and the self-learning procedure

shall be performed again.

N.B. The thermostat will send the switch-on/-off

controls for the three fans and the two valves

to the actuator to a ﬁxed rate of 1 minute.

Warning! The conﬁguration shall be performed

only by qualiﬁed personnel.

Table des matières

Autres manuels Fantini Cosmi Thermostat

Fantini Cosmi

Fantini Cosmi CH115TS Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH180RFWIFI Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH150RF Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH180WIFI LITE Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH143A Manuel utilisateur

Fantini Cosmi

Fantini Cosmi Intellitherm C57 Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH191 Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH180WIFI LITE Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH130RR Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH140GSM Manuel utilisateur

Fantini Cosmi

Fantini Cosmi O62C Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH119NFC Manuel utilisateur

Fantini Cosmi

Fantini Cosmi C801 Manuel utilisateur

Fantini Cosmi

Fantini Cosmi Intellicomfort+ CH180RF Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH110R Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH140GSM2 Manuel utilisateur

Fantini Cosmi

Fantini Cosmi Intellitherm C32 Manuel utilisateur

Fantini Cosmi

Fantini Cosmi L03B Manuel utilisateur

Fantini Cosmi

Fantini Cosmi C800WIFI Manuel utilisateur

Fantini Cosmi

Fantini Cosmi Intellicomfort CH180 Manuel utilisateur

Fantini Cosmi

Fantini Cosmi CH115RF Manuel utilisateur

Fantini Cosmi

Fantini Cosmi EVWC8R Manuel utilisateur

Fantini Cosmi

Fantini Cosmi C01A Manuel utilisateur

Fantini Cosmi

Fantini Cosmi C68 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur