F&F LE-03d Manuel utilisateur

- 1 -

LE-03d

Electric energy meter,

3-phase

Directive MID 2014/32/EU

Certificate number 0120/SGS0119

The LE-03d is a static (electronic) calibrated electricity meter of

three-phase alternating current in a semidirect system.

A special electronic system under the influence of flowing cu-

rrent and applied voltage in each phase generates pulses pro-

portional to the energy drawn in the respective phase. Energy

consumption in the phase is indicated by a flashing of correspon-

ding LED (A, B, C). The sum of the three phase pulses is indicated

by a flashing LED and converted into energy absorbed througho-

ut the three-phase system. Its value is displayed by the segment

LCD display.

The fractional digit represent the decimal (.1 kWh = 100 Wh).

Compliance

Purpose

Functioning

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: biuro@fif.com.pl

Do not dispose of this device in the trash along with other waste!

According to the Law on Waste, electro coming from households free of charge and can

give any amount to up to that end point of collec� on, as well as to store the occasion of

the purchase of new equipment (in accordance with the principle of old-for-new, regard-

less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the

environment and human health.

- 2 -

Active energy consumed AE+ [kWh]

The indicator has a pulse output. This allows you to connect a

pulse meter-reading pulses generated by the counter. For proper

operation of the indicator is not required to connect additional

devices.

The meter has sealable input and output terminal covers to pre-

vent any attempts to bypass the meter.

Measured value

Pulse output

Sealing

- 3 -

The meter is marked with individual serial number allowing its

unambiguous identification. The marking is laser engraved and

cannot be removed).

Meter number

Front description

- 4 -

1.Disconnect the power supply.

2.The indicator mounted on a rail in the distribution box.

3.Connect the power in accordance with the markings to the

terminals 1 (L1), 3 (L2), 5 (L3).

4.Connect the measured circuit or a single receiver to the termi-

nals in accordance with the markings to the terminals 2 (L1),

4 (L2), 6 (L3).

5.N-wire connect to terminal 7.

6.Additional pulse receiver connected (optional) to terminals

9(+) and 8(–).

Additional pulse receiver is not required.

7.Put the meter terminals covers.

Dimensions

Mounting

- 5 -

1 power input L1IN

2 power output L1OUT

3 power input L2IN

4 power output L2OUT

5 power input L3IN

6 power output L3OUT

7 neutral N-wire

8 pulse output (–)

9 pulse output (+)

Wiring diagram

- 6 -

installation 4-wire

rated voltage 3×230/400 V

minimum measured current 0.04 A

base current 3×10 A

maximum current 3×100 A

voltage measuring range 160÷265 V

measurement accuracy (EN50470-1/3) B class

rated frequency 50 Hz

insulation protection class II

housing PC+ABS material

own power consumption <10 VA; <0.2 W

indication range 0÷999999.9 kWh

constant 1000 pulses/kWh

current consumption signalling A, B, C phases 3× red LED

read-out signalling red LED

pulse output

type open collector

maximum voltage 27 V DC

maximum current 27 mA

pulse time 35÷80 ms*

working temperature -20÷55°C

terminal 25 mm² screw terminals

dimensions 7 modules (122 mm)

mounting on TH-35 rail

ingress protection IP20

__________

* depends on the current consumption

Technical data

- 7 -

F&F products are covered by a 24-month warranty from the date

of purchase. The warranty is only valid with proof of purchase.

Contact your dealer or contact us directly.

F&F Filipowski sp. j. declares that the device is in conformity

with the essential requirements of The Low Voltage Directive

(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)

Directive 2014/30/UE.

The CE and MID Declaration of Conformity, along with the refe-

rences to the standards in relation to which conformity is decla-

red, can be found www.fif.com.pl on the product subpage.

Warranty

CE declaration

- 8 -E210430

»Please read the instructions carefully before installation.

»The device should be installed and operated by qualified per-

sonnel who are familiar with its design, operation, and asso-

ciated risks.

»Do not install a meter that is damaged or incomplete.

»The user is responsible for proper grounding of the system,

proper selection, installation, and efficiency of other devices

connected to the meter, including safety devices such as over-

current, residual current and overvoltage circuit breakers.

»Before connecting the power supply, make sure that all cables

are connected correctly.

»It is essential to observe the operating conditions of the meter

(supply voltage, humidity, temperature).

»To avoid electric shock or damage to the meter, turn off the

power supply whenever the connection is changed.

»Do not make any changes to the unit yourself. Doing so can

result in damage to or improper operation of the device,

which in turn can pose a threat to people operating it. In such

cases, the manufacturer is not responsible for the resulting

events and may refuse the provided warranty in the event of

a complaint.

»Do not tighten the terminals without the wire inserted. This

may damage the lift mechanism of the terminal or the plastic

cover of this terminal.

General work safety conditions

Table des matières

Autres manuels F&F Instrument de mesure

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur