Fanaway CLASSIC Manuel utilisateur
V2.0 –EN –AU WS Classic ( 07/ 2018)
FANAWAY CLASSIC
CEILING FAN
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.
Fanaway Classic Installation Instructions
2 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Fanaway product. To ensure correct function and safety, please
read and keep all instructions before using the product.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Cleaning and maintenance shall not be undertaken by children
without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless theyhave been
given supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means
for an all-pole disconnection incorporated in the fixed wiring in
accordance with the wiring rules.
Fanaway Classic Installation Instructions
3 | P a g e
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to
be an all-pole disconnection to the ceiling fan electrical circuit,
meeting the requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the
same room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 50kg.
7. The fan should be mounted so that the blades are at least 2.3m above the floor in Europe or 2.1m
above the floor in Australia.
8. This fan is designed for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and will void the warranty.
9. Only a licensed electrician should execute the installation.
Fanaway Classic Installation Instructions
4 | P a g e
BEFORE INSTALLATION
Unpack your ceiling fan and carefully identify the parts. Please refer to Fig 1.
Fanaway Classic Installation Instructions
5 | P a g e
Fig. 1
Fanaway Classic Installation Instructions
6 | P a g e
1
Mounting bracket x 1
10
Retraction mechanism x 1
2
Canopy screws x 4
11
Lamp base x 1
3
Canopy x 1
12
Lamp shade x 1
4
Down rod x 1
13
Light kit x 1
5
Bolt and pin cover x 1
14
Light kit screw x 3
6
Bolt x 1
15
Wooden screw x 2
7
Pin x 1
16
Wall swtich x 1 set
8
Top housing x 1
17
9
Blades x 4
INSTALLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from
the tip of the blade to the nearest objects or walls.
Secure the hanging bracketto the ceiling joist or structure that is capable of carrying a load of at least
50kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into the
support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used.
Angled Ceiling Installation
This fan hanging system supports a maximum 15 degree angled
ceiling installation.
Fig. 2
Fig. 3
Fanaway Classic Installation Instructions
7 | P a g e
INSTALLING THE FAN
Installing the down rod
1) Feed the down rod (5) through the canopy (4) and the bolt and pin cover (6).
2) Remove the ball joint (2) by loosening the set screw (3), insert the motor wires through the down
rod then secure the ball joint back to the down rod.
3) Insert the down rod to the coupling (7), line up the coupling holes with the down rod holes and
insert the bolt (8). Then insert the pin (9) to the end of the bolt.
4) Finally secure the down rod and coupling by tightening the two set screws (10) on the coupling.
Fig. 4
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the registration slot (A) of the hanger ball is
positioned on the stopper (B) of the mounting bracket (C) to prevent the fan from rotating when in
operation. (Fig.5)
Fig. 5
Fig. 4
Fanaway Classic Installation Instructions
8 | P a g e
FAN INSTALLATION
Light kit installation
1. Loosen the screw (1) from the lamp shade bracket (3). Align the two slot screws (2) with the keyhole
slots of the lamp shade (4). Fig.6
2. Turn the lamp shade counterclockwise until the slot screws are firmly at the end of the slots.
3. Secure screw 1 back to the lamp shade bracket. Tighten all three screws. Do not over-tighten.
4. Connect the plugs (8) together.
5. Loosen the screw (5) from the lamp shade (4). Align the two slot screws (6) with the keyhole slots of
the light kit (7). Fig.7
6. Turn the light kit counterclockwise until the slot screws are firmly at the end of the slots.
7. Secure screw 5 back to the lamp shade. Tighten all three screws. Do not over-tighten.
8. Install the globes (Not included) to the lamp holders.
Fig. 6
Fig. 7
Fanaway Classic Installation Instructions
9 | P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION MUST BE INCORPORATED IN THE FIXED
WIRING IN ACCORDANCE WITH THE WIRING RULES.
USE WITH WALL SWITCH WIRING DIAGRAM:
USE WITH REMOTE WIRING DIAGRAM: (REMOTE sold seperately)
1/ Remote without plugs
Fig. 9
Fig. 10
Fanaway Classic Installation Instructions
10 | P a g e
2/ Remote with plugs
FINISHING THE INSTALLATION
After completing the electrical connection at the mounting bracket terminal block, connect the ceiling
fan wiring via the quick connector plug.
Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy
and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using
the screws provided.
Fig. 12
Fig. 11
Autres manuels pour CLASSIC
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fanaway Ventilateur
Fanaway
Fanaway CORBELLE Guide d'installation
Fanaway
Fanaway MYA Manuel utilisateur
Fanaway
Fanaway EVO2 Manuel de service
Fanaway
Fanaway LD-0003-11/WH/GS Manuel de service
Fanaway
Fanaway EVORA Manuel utilisateur
Fanaway
Fanaway EVO3 Manuel de service
Fanaway
Fanaway FANAWAY FRASER Manuel utilisateur
Fanaway
Fanaway EVO1 - PREVAIL Manuel utilisateur
Fanaway
Fanaway LED EVO1 Manuel utilisateur
Fanaway
Fanaway NEXUS Manuel utilisateur
Fanaway
Fanaway CORBELLE Guide d'installation
Fanaway
Fanaway ORBIT DC Manuel du propriétaire
Fanaway
Fanaway VEIL Manuel utilisateur
Fanaway
Fanaway ORBIT Manuel utilisateur
Fanaway
Fanaway Montclair Manuel utilisateur
Fanaway
Fanaway XIAO Manuel utilisateur
Fanaway
Fanaway LED EVO1 Manuel utilisateur
Fanaway
Fanaway LED EVO1 Guide d'installation
Fanaway
Fanaway CLASSIC Guide d'installation
Fanaway
Fanaway ORBIT Manuel utilisateur
