Falcon ED1000RM-1 Manuel d'utilisation

OWNER'S

OPERATING

MANUAL

UNINTERRUPTIBLE POWER SYSTEM

FOR MODELS:

ED1000RM-1

ED2000RM-1

ED2400RM-1

ED2500RM-1

FALCON®ELECTRIC INC.

Irwindale, CA 91706

Tel. 626-962-7770

Fax. 626 962-7720

The information contained herein is the property of FALCON®ELECTRIC INC., is proprietary, confidential, and not to be disclosed, disseminated or used except for the

purpose provided.

5116 Azusa Canyon Road

TABLE OF CONTENTS

Important Safety Instructions (READ FIRST) . . 1

Chapter 1, ED Series UPS Overview .... 2

Model Cross Reference Table .... 2

Block Diagram ...... 3

Selection Guide ...... 4

Chapter 2, Installation ...... 5

Inspecting the Equipment .... 5

UPS Setup ....... 5

Chapter 3, Controls, Displays & Functions . . . 6

Front Panel Diagram & Description . . . 6

Front Panel LED Functions .... 6

Rear Panel Diagram & Description . . . 7

Chapter 4, Communications Interface.... 8

Signals & Interfacing ..... 8

Chapter 5, Operation ...... 9

Step By Step Operating Procedure . . . 9

Operational Mode Table .....10

Chapter 6, Maintenance & Technical Support . . 11

Care & Maintenance .....11

Battery Life vs. Temperature ....11

Battery Replacement .....11

Storing the UPS and Batteries ....12

FCC . . .....12

Technical Support & RMA Procedure ...13

Requesting Technical Information or Support. . 13

FALCON Web Support .....13

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions which must be followed during the

installation, operation and maintenance of this UPS and it’s batteries. Please read

all instructions before operating this equipment and save this manual for future

reference.

All of the models presented herein are designed for installation and use in a con-

trolled environment free of contamination.

This UPS utilizes voltage that may be hazardous. Do not attempt to disassemble .

This unit contains no user replaceable parts. Refer all servicing to Falcon Electric,

Inc.

This UPS is not intended to be used in conjunction with life support or operating

room equipment.

Always unplug this UPS prior to cleaning and never apply liquid or spray detergent

on the UPS.

Never attempt to service batteries. High voltage exists within the unit, which could

cause electrical shock. Servicing of batteries should be performed or supervised

by personnel knowledgeable of batteries and the required precautions. Keep unau-

thorized personnel away from batteries. When replacing the UPS batteries, use the

same number and type of batteries.

Allow at least 24 hours, after the UPS is first installed and turned on, to fully charge

the internal battery and assure the maximum backup time is available.

DO NOT plug this UPS into its own output as this may damage the UPS.

DO NOT remove or unplug the input cord when the UPS is turned on. This

removes the safety ground from the UPS and the equipment connected to the UPS.

This UPS contains its own energy source (batteries). The output receptacles

may carry live voltage even when the UPS is not connected to an AC source.

CAUTION

IMPORTANT

DO NOT

CAUTION

CHAPTER

CHAPTER 1

ED Series UPS - Overview

Congratulations! You have selected the highest quality protection for your

computer today. The FALCON®ED Series UPS offers a quiet and compact

package with superior performance you can depend on. You now own a

member of the ED family which is a proud part of the very reliable and versatile

FALCON® ED Series of UPS.

This User’s Guide is provided with your new ED unit. It will enhance your

understanding of the product and its functions. Read this handbook carefully in

the order it is presented prior to operating your unit. This will save you time and

effort in your installation and application. The illustrations will also familiarize

you with the ED's operating modes and indications. Always operate the unit

within the guidelines and specifications given to maximize the unit's efficiency

and lifetime. Also, your understanding of the product is essential in providing

you years of service for your back-up power requirements.

Refer to the cross-reference table below to understand which unit with it's power

capability corresponds to your particular model number.

MODEL NUMBER

OUTPUT POWER (VA)

ED1000RM-1

1000 (700 Watts)

ED2000RM-1

2000 (1400 Watts)

ED2400RM-1

2400 (1680 Watts)

ED2500RM-1

2500 (1750 Watts)

CROSS REFERENCE TABLE

The FALCON®ED Series represents one of the smallest and most compact

units of the FALCON®UNINTERRUPTIBLE POWER SYSTEM (UPS) product

line. In the tradition of all FALCON®products, it maintains the highest reliability

and the most complete on-line, sinewave power protection available. An on-

line, sinewave UPS is the only total solution to virtually any power problem. It

effectively provides just what it says, UNINTERRUPTIBLE POWER. There is

no break, transient or glitch in source transfer during a power failure because

THERE IS NO TRANSFER.

The FALCON®ED SERIES is engineered with the latest MOSFET/PWM

technology for high efficiency and reliability.

Refer to the simplified block diagram, Figure 1, for a system description. The

AC source is rectified and provides energy for the DC + Choppers and a float

charge to a standby Battery. These DC Choppers then supply the power to

operate the DC/AC Inverter.

During a utility power-loss, the AC rectification and battery charging capabilities

of the UPS become inactive. The fully-charged battery, however, supplies the

necessary power requirement to maintain the remaining system blocks.

The FALCON®ED on-line topology is unique to other on-line systems, in that, it

is designed to meet the needs of non-linear loads. Your computer, with its

switching power supply, is considered a non-linear load which can be very

abusive to most power protection equipment and could decrease its life-

expectancy. The FALCON®ED unit is specially devised to accept these loads

and protect them efficiently without any of the output waveform degradation

common to other UPS.

Referring again to the figure below, you will notice a built-in safeguard. If the

unit inadvertently experiences an extreme over temperature situation that

causes inverter malfunction, it will switch over to a filtered emergency bypass

line to insure continuous power to the computer load. If the unit is overloaded, it

will shutdown completely if the overload is not corrected within 15 seconds.

INPUT

FILTER

RECTIFIER

CHARGER

+DC

CHOPPERS

DC/AC

INVERTER

OUTPUT

FILTER

COMPUTER

(LOAD)

STANDBY

BATTERY

EMERGENCY

BYPASS LINE

EMERGENCY

BYPASS

SWITCH

FIGURE 1: FALCON ED SERIES BLOCK DIAGRAM

UNIT NAME

E D 1000R M -1

E D 2000R M -1

E D 2400R M -1

E D 2500R M -1

Nom inalVA

1000

2000

2400

2500

Current-Input

10.4A

19A

24A

25A

Current-Output

RMS

N on-Linear(R epetitive P eak)

8.3A

20A

16.7A

38A

20.0A

45.6A

20.9A

47.6A

InputLine Plug

L5-15p

L5-30P

OutputDistribution C onnectors3

(4)5-15R

Height in(cm )

3.5 (8.9)

Width in(cm ) FrontP anel

C hassis

19.0(8.3)

17.18 (43.64

D epth in(cm )

20.25 (51.5)

Weight lbs(kg)

50 (22.7)

56 (25.4)

Std.Back-Up

4(min)

100% Load/50% Load

8/20

5/14

4/9

MODEL SELECTION GUIDE

CHAPTER

CHAPTER 2

Installation

Inspecting the Equipment

If any FALCON®equipment has been damaged during shipment, keep

the shipping cartons and packing materials for the carrier and file a

claim for shipping damage. If you discover damage after acceptance,

file a claim for concealed damage.

To file a claim for shipping damage or concealed damage: 1) File with

the carrier within 15 days of receipt of the equipment; 2) Send a copy

of the damage claim within 15 days to the Falcon®Service Department.

UPS Setup

1. Verify that the following is included in the UPS shipping carton:

UPS, Owner's Guide..

2. Verify that the UPS unit is configured for the proper input/output

voltage. This information is stated on the nameplate label located on

the rear panel of the unit.

3. Select a suitable location for the UPS, near enough to the computer or

equipment to allow connection of the equipment power plug to the

receptacles located on the rear panel of the UPS.

4. When installing this UPS into a rack enclosure the following must be

followed:

a. Due to the UPS weight it must be installed using a rack

mounted shelf or using slides manufactured by General

Devices, part number CLB-203-20, using (8) Phillips, pan

head 8-32 x 3/8” screws, (4) per slide.

b. Secure the UPS front panel to the rack rails using four screws

supplied by the rack manufacturer.

5. DO NOT BLOCK UPS AIR VENTS. THE UPS MUST NOT BE

INSTALLED IN AN ENCLOSED AREA.

6. If you have not already done so, connect the equipment to be

protected to the UPS output receptacles located on the rear panel.

Verify that the connected equipment does not exceed the rated output

(in watts) of the UPS.

IMPORTANT

7. Plug the UPS power cord into the nearest grounded wall outlet. If the

UPS does not power up automatically, depress and hold the control

button located on the UPS front panel until the UPS turns on.

CHAPTER

CHAPTER 3

Controls, Displays & Functions

1. INPUT POWER CIRCUIT BREAKER & INDICATOR

Pull button to remove input power. The UPS will go into battery mode

when pulled.

Push the button in to reset the circuit breaker.

2. UPS OUTPUT CIRCUIT BREAKER & INFDICATOR

This circuit breaker provides overload protection for the UPS. Pull the

button to turn off the UPS output. Push the button to reset the circuit

breaker.

3. AC- AC LINE INDICATOR

This green LED turns on when the utility AC is present.

4. INV- INVERTER OPERATING

The LED turns green when the UPS inverter is turned on. This LED

normally turns on a few seconds after the AC line indicator LED and

remains on during both utility and battery operation.

5. ALM- ALARM STATUS INDICATOR

This red LED turns on and a continuous audible alarm is sounded when

the UPS is overloaded or has failed. Should this occur, check the load

level and correct any overload condition if present. During this condition,

UPS load outlets will be powered by filtered utility bypass power.Should

the unit not be overloaded, call FALCON®support for further assistance..

6. LOW BATT.- LOW BATTERY WARNING INDICATOR

The red LED will turn on when the UPS is operating in battery mode

and the low battery level warning point has be reached. Typically one

minute of battery runtime remains after the LED turns on.

7. OVERLOAD/ FULL LOAD/ 75% LOAD/ 50% LOAD-

Adjacent to the red low battery LED is the green 50% load LED.

Adjacent to the green 50% load LED is the green 75% load LED.

Adjacent to the green 75% load LED is the yellow 100% load LED.

Adjacent to the yellow 100% LED is the red overload LED. All overload

conditions must be corrected immediately.

8. UPS ON/OFF SWITCH

WARNING! Ths switch turns the UPS on and off. Turning this switch

to the off position will trun off power to the connected load.

345768

NOTE: Reference page 10 for more details

TYPICAL UPS REAR PANEL LAYOUT

9. DB-9F CONTACT CLOSURE INTERFACE

This connector gives access to the UPS contact closure status interface.

Please reference page 8 of this manual for details.

10. Inlet for Input Line Cord on ED1000-1 only. Line cord permenently

attached to ED1500-1 and ED2000-1.

11. COOLING FANS (2)

Cooling fans draw cool air from the outside of the rear panel and

exhaust it out through slots in the UPS front panel. ALWAYS KEEP

COOLING FAN AND FRONT PANEL VENTS CLEAR OF DEBRIS. DO

NOT OPERATE THE UPS IN AN ENCLOSED SPACE.

12. TEST JUMPER

For test purposes only, donot remove

CHAPTER

CHAPTER 4

DB-9 COMMUNICATIONS INTERFACE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Falcon UPS

Falcon

Falcon UNINTERRUPTIBLE POWER SUPPLY MODELS SG1K-2T Manuel utilisateur

Falcon

Falcon SSG1.5KRM-1 Mode d’emploi

Falcon

Falcon SSG1.5KRM-1 Manuel d'utilisation

Falcon

Falcon SSG6KRM-2 Mode d’emploi

Falcon

Falcon FN3K-2TXI Manuel d'utilisation

Falcon

Falcon SG5K-1TX Manuel d'utilisation

Falcon

Falcon SG2K-X1T Manuel d'utilisation

Falcon

Falcon SSG1.5KRM-2 Mode d’emploi

Falcon

Falcon ED-1000-1 Manuel utilisateur

Falcon

Falcon SSG500VA-1 Manuel d'utilisation

Falcon

Falcon UNINTERRUPTIBLE POWER SUPPLY MODELS SG2K-1T Manuel d'utilisation et d'entretien

Falcon

Falcon XG1.5K-1T Manuel d'utilisation

Falcon

Falcon SG5K-1TX Manuel d'utilisation et d'entretien

Falcon

Falcon ED-1000-1 Manuel utilisateur

Falcon

Falcon SG800-1T Manuel d'utilisation

Falcon

Falcon FN2-4.5K-2TXI Mode d’emploi

Falcon

Falcon SG800-1, SG800-2 SG1K-1T, SG1K-2T SG2K-1T Manuel d'utilisation et d'entretien

Falcon

Falcon ED Series Manuel d'utilisation

Falcon

Falcon FN2 Series Mode d’emploi

Falcon

Falcon UPS Plus SG Series Manuel d'utilisation

Falcon

Falcon SG700RM-1SC Manuel utilisateur

Falcon

Falcon MLP-300-1 Manuel utilisateur

Falcon

Falcon RACKMOUNT UPS PLUS FN3KRM-2 Manuel d'utilisation

Falcon

Falcon ED3000-A Manuel d'utilisation

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur