Extron electronics XTP SFR HD 4K Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the

complete user guide

, installation

instructions, and specifications.

XTP SFR HD 4K • Setup Guide

CLASS 1 LASER PRODUCT, see the XTP SFR HD 4K User Guide at www.extron.com

The Extron XTP SFR HD 4K is an XTP ber receiver that scales HDMI, DVI, RGB, HD component video, and standard denition

video to the optimal output resolution. This guide provides instructions for an experienced installer to install and connect the

XTP SFR HD 4K scaling receiver.

Installation

Rear Panel Features

Power and Throughput Connections Output Connections Control Connections and Reset

A DC power connector and power LED

B XTP input connector

C LAN connector and LEDs

D RS-232 and IR Over XTP connector

E HDMI output connector and

corresponding HDMI audio switch

F Analog audio output connector

G S/PDIF digital audio output connector

H Relay connectors

I Remote RS-232 connector

J Reset button

Figure 1. Rear Panel Features

Mounting and Cabling

Step 1 — Mount the device

Turn off or disconnect all equipment power sources and mount the XTP SFR HD 4K on a tabletop or in a rack.

Step 2 — Connect throughput devices

a. Connect an XTP transmitter or XTP matrix switcher to the XTP ber input connector (B).

WARNING: Potential risk of severe injury. The XTP SFR HD 4K outputs continuous invisible light (class 1 laser rated),

which may be harmful to the eyes; use with caution.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. Le XTP SFR HD 4K émet une lumière invisible

en continu (conforme à la classe 1 laser) qui peut être dangereux pour les yeux, àutiliser avec précaution.

• Do not look into the ber optic cable connector or into the ber optic cables themselves.

• Ne regardez pas dans le connecteur de câble bre optique sur le ou dans les câbles bre optique euxmêmes.

• Plug the attached dust caps into the connector when the ber optic cable is unplugged.

• Branchez la protection contre la poussière dans le connecteur lorsque le câble bre optique est débranché.

Signal LED indicator — Lights green when it receives an active XTP input signal from a transmitter or matrix switcher.

Link LED indicator — Lights yellow when a valid link between an XTP input and output is established.

b. Connect a host device or control LAN or WAN to the LAN RJ-45 connector (C) for pass-through 10/100 Ethernet

communication. These are Ethernet pass-through ports with LEDs to indicate link and activity status.

c. To pass bidirectional serial, infrared, or other control signals, connect a control device or a device to be controlled to the

RS-232 and IR Over XTP connector (D). See RS-232 and IR Over XTP Wiring on page 2 for wiring details.

Step 3 — Connect outputs

a. Connect a digital video display to the HDMI output connector (E) on the receiver.

b. Connect a balanced or unbalanced stereo or mono audio device to the 3.5 mm, 5-pole captive screw connector (F) on the

receiver for 2-channel stereo analog audio (see Audio Wiring on page 2 for wiring details).

c. Connect an audio device to the female orange RCA connector (G) tor for digital S/PDIF audio output.

Step 4 — Connect control devices

a. Connect a host device, such as a computer, to the front panel female USB mini-B connector (see ﬁgure 2, Bon page 2) to

congure the device or update rmware.

b. Connect equipment controlled via momentary or latching contact, like projector screens or lifts, to these normally open

relays (H). Do not exceed 24 V at 1 A for each port.

c. For serial control of the scaler, connect a host device to the Remote RS-232 3.5 mm, 3-pole captive screw connector (I).

Step 5 — Connect power

Connect the provided external power supply to the 2-pole captive screw connector (A).

POWER

12V

1.0 A MAX

HDMI S/PDIF

AUDIOAUDIO

SIG LINK LAN

RS-232 RS-232IR L

Tx Rx Tx Rx

RESET

R12ON

OFF

XTP IN OVER XTP OUTPUTS RELAYS

Tx Rx G

REMOTE

ABCD EFGH IJ

XTP SFR HD 4K • Setup Guide (Continued)

Connection Details

RS-232 and IR Over XTP Wiring

To pass bidirectional serial command signals between XTP-compatible devices, connect

a control device to the three leftmost poles (Tx, Rx, and G) of the 5-pole captive screw

connector. To transmit and receive IR signals, connect a control device to the three rightmost

poles (G, Tx, and Rx).

NOTE: RS-232 and IR data can be transmitted and received simultaneously.

Audio Wiring

Wire the audio output connector as

shown to the right. Use the supplied

tie wrap to strap the audio cable to the

extended tail of the connector.

ATTENTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the

negative (–) contacts.

ATTENTION : Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux

contacts négatifs (–).

NOTE: The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm).

Operation

After all transmitters and connected devices are connected and powered on, the system is fully operational. If any issues arise,

verify that the cables are routed and connected properly.

NOTE: Use the Extron XTP System Conguration Software or Simple Instruction Set (SIS) commands to congure the scaler

(see the XTP SFR HD 4K User Guide on the Extron website).

Front Panel Overview

XTP SFR HD 4K

SIGNAL

ADJUST

Extron HDCP

HBR

HDMI

BITSTREAM

S/PDIF

LPCM

MENUENTER

ANALOG

CONFIG

AUDIOXTP

BAC DEFG

Figure 2. Front Panel Features

APower LED indicator — Lights on the front and rear panels when power is applied to the device.

BConfiguration port — Connect a host device to the USB mini-B port for device configuration, control, and firmware upgrades.

CXTP LED indicators

Signal LED — Lights when an active XTP video signal is received.

HDCP LED — Lights when the XTP input signal is encrypted.

DAudio LED indicators

HBR LED — Lights when the embedded audio signal is high bit rate audio.

Bitstream LED — Lights when the embedded audio input signal is Dolby Digital, DTS audio format, and 2-ch Dolby.

LPCM LED — Lights when the embedded audio input signal is 2-channel LPCM.

HDMI LED — Lights when HDMI embedded audio output (HBR, bitstream, or LPCM) is enabled.

S/PDIF LED — Lights when S/PDIF audio output (multi-channel or LPCM) is enabled.

Analog LED — Lights when analog audio output is enabled.

EMenu button — Press this button to access and navigate the on-screen display (OSD) menu system.

FEnter button — Press this button to select submenus and submenu items.

GAdjustment knobs — Rotate the horizontal and vertical knobs to navigate the on-screen display menu and to adjust settings.

Tx/Rx

Pins

RxTx

RS-232

RxTx

TxRx

RxTx

IR Device

RS-232 Device

Do not tin

the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Front Panel Lockout Mode (Executive Mode)

The front panel security lock (executive mode) limits operation of the device from the front panel. While in executive mode, the

XTP SFR HD 4K can still be congured with SIS commands and the XTP System Conguration Software. To enable or disable

executive mode through the front panel, press and hold the Menu and Enter buttons simultaneously for 2 seconds or until the

power LED blinks. Executive mode can also be enabled or disabled using SIS commands (see the Advanced conﬁguration

commands on the next page) or the XTP System Conguration Software.

HDMI Audio

The embedded audio on the HDMI output connector can be enabled or disabled by setting the HDMI audio switch next to the

connector (see ﬁgure 1, Eon page 1). Move and hold the HDMI audio switch up (for about 1 second) to enable embedded audio

on the display connected to the HDMI output connector, or move and hold the HDMI audio switch down (for about 1 second)

to disable it. The switch returns to the middle position after it has been released. The associated LED lights when the audio is

enabled and remains unlit when audio is disabled.

Firmware Upgrades

The onboard rmware of the XTP SFR HD 4K can be upgraded via the XTP System Conguration Software or the Extron Firmware

Loader Program (available on the Extron website, www.extron.com).

Conﬁguration

The XTP SFR HD 4K can be congured through front panel controls and the On-screen Display (OSD) menu, Simple Instruction

Set (SIS) commands, or the XTP System Conguration Software. To utilize SIS commands or access the XTP System

Conguration Software, connect a host device to the XTP SFR HD 4K through the front panel conguration port (see ﬁgure 2, B

on page 2) or the rear panel Remote RS-232 connector (see ﬁgure 1, Ion page 1). The conguration port supports SIS

commands and the XTP System Conguration Software while the Remote RS-232 connector supports only SIS commands.

On-Screen Display (OSD) Menu System

The OSD menu consists of six submenus that can be accessed using the front panel Menu button (see ﬁgure 2, Eon page 2).

View the menu on a display connected to the HDMI output connector (see ﬁgure 1, Eon page 1). The submenus are:

• Image Reset — Use this submenu to perform a one-time Image Reset on the image. The image is centered and sized to ll

the output screen.

• Picture Control — Use this submenu to adjust the horizontal and vertical position, horizontal and vertical size, brightness,

contrast, and detail of the image.

• User Presets — Use this submenu to save or recall a user preset.

• Input Configuration — Use this submenu to view the total pixels and horizontal and vertical active pixels of the input signal.

• Output Configuration — Use this submenu to select an output rate from a list of common resolutions and refresh rates or

view color bit depth, and output format settings.

• Advanced Configuration — Use this submenu to apply a test pattern, enable or disable a blank screen, freeze the output,

set the aspect ratio, or reset the receiver to factory default settings.

To adjust settings in the OSD menu:

1. Press the Menu button to access the main menu.

2. Rotate either adjustment knob to navigate to a desired submenu.

3. Press the Enter button to access the items of the selected submenu.

4. Rotate either adjustment knob to navigate to a desired submenu item.

5. Press the Enter button to select a submenu item for adjustment.

6. As required, rotate the adjustment knobs or press the Enter button to adjust submenu items.

7. Press the Menu button to return to the list of submenus or exit the OSD menu.

XTP System Conﬁguration Software

The XTP SFR HD 4K can be congured by the XTP System Conguration Software when it is installed on a connected host

device, such as a PC, through the front panel USB port (see the XTP SFR HD 4K User Guide for more details).

468-2203-50 Rev. B

02 19

Basic SIS Commands

To use SIS commands, connect the XTP SFR HD 4K to a host device through the RS-232 or USB connector. Use the Extron

DataViewer utility or a control system to send SIS commands and receive responses. The following table identies a selection of

SIS commands (for a full list, see the XTP SFR HD 4K User Guide at www.extron.com).

Command ASCII Command

(Host to Device)

Response

(Device to Host)

Additional Description

Picture adjustments

Execute image reset AImg]Execute a one time image reset.

Mute video 1B Vmt1]Mute video and display a black screen.

Mute video and sync 2B Vmt2]Mute video and sync.

Unmute video 0B Vmt0]Unmute the video.

Output configuration

Set scaler output rate EX3$RATE}RateX3$] Set the output resolution and refresh rate.

View scaler output rate ERATE}RateX3$] View the selected output resolution and refresh

rate.

Set a test pattern X1!J TstX1!] Set the test pattern to X1!.

View the test pattern JTstX1!] View the current test pattern status.

Audio configuration

Mute all audio 7Z Amt7]Mute all audio outputs.

Unmute audio 0Z Amt0]Unmute all audio outputs.

Set volume level X1&V VolX1&] Set the output volume to X1&.

View volume level VVolX1&] View the current volume setting.

Advanced configuration

Enable executive mode 1X Exe1]Lock the front panel.

Disable executive mode 0X Exe0]Unlock the front panel.

Set aspect ratio to Fill E1ASPR}Aspr1]Fill the entire output screen.

Set aspect ratio to Follow E2ASPR}Aspr2]Match the native value.

View aspect ratio setting EASPR}AsprX2#] View the current aspect ratio setting.

Reset

Reset to factory default EZXXX}Zpx]Resets all user settings back to factory defaults.

KEY:

X1! = Test pattern (0= off [default], 1= crop, 2= alternating pixels, 3= crosshatch, 4= color bars, 5= grayscale)

X1& = Volume (0-64, where 64 = default)

X2# = Input aspect ratio (1= Fill [default], 2= Follow)

X3$ = Output scaler resolution and refresh rate (see the table below for a selection of resolutions and refresh rates or the

XTP SFR HD 4K User Guide for a full list)

SIS Variable X3$ for Selected Output Resolution and Refresh Rate Combinations (Where X3$ = 1 through 68, 0)

Resolution 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz

1024x768 3

1280x800 5

1280x1024 6

1680x1050 12

1920x1200 14

720p 23 24 25 26 27 28

1080p 32 33 34 35 36 37 38 39*

2K (2048x1080) 40 41 42 43 44 45 46 47

4K (3840x2160) 64 65 66 67 68

Bypass scaling 0

All trademarks mentioned are the property of their respective owners.

Autres manuels pour XTP SFR HD 4K

Table des matières

Autres manuels Extron electronics Récepteur

Extron electronics

Extron electronics Twisted Pair Transmitter VTT001 Manuel utilisateur

Extron electronics

Extron electronics FOX 500 Tx Manuel utilisateur

Extron electronics

Extron electronics MTP 15HD A Series Manuel utilisateur

Extron electronics

Extron electronics DDTX/DDRX DVI Manuel utilisateur

Extron electronics

Extron electronics Receivers TP Series Manuel utilisateur

Extron electronics

Extron electronics XTP R HDMI Manuel utilisateur

Extron electronics

Extron electronics XTP SR HDMI Manuel utilisateur

Extron electronics

Extron electronics HC 402 EU Manuel utilisateur

Extron electronics

Extron electronics DFX 100 Tx Manuel utilisateur

Extron electronics

Extron electronics Dual Link DVI Transmitter and Receiver DVI DL 201... Manuel utilisateur

Extron electronics

Extron electronics FOX II T DP 4K Manuel utilisateur

Extron electronics

Extron electronics MTP 1500RL 15HD A SEQ Manuel utilisateur

Extron electronics

Extron electronics XTP SR HDMI Manuel utilisateur

Extron electronics

Extron electronics IN1124 Manuel utilisateur

Extron electronics

Extron electronics FOX 2G Tx AV Manuel utilisateur

Extron electronics

Extron electronics MTP 15HD RS Series Manuel utilisateur

Extron electronics

Extron electronics MTP R 15HD RSA D Manuel utilisateur

Extron electronics

Extron electronics DFX 100 Series Manuel utilisateur

Extron electronics

Extron electronics TP Receivers Family Manuel utilisateur

Extron electronics

Extron electronics MTP U R RSA SEQ Manuel utilisateur

Extron electronics

Extron electronics Digital Video Transmitter and Receiver DVI 201... Manuel utilisateur

Extron electronics

Extron electronics FOXBOX Tx HDMI Manuel utilisateur

Extron electronics

Extron electronics FOX 2G Tx AV Manuel utilisateur

Extron electronics

Extron electronics MTP 1500RL 15HD A SEQ Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur