Extron electronics VSC 900 Manuel utilisateur

User’s Guide

70-065-02 Upgrade Kit

68-735-01 Rev. A

Printed in the USA

09 03

VSC 700/900 SDI Output Card

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

VSC 700/900 SDI Output Card • Installation

Installation

Installing the SDI Ouput Card

The SDI output card may be installed in the VSC 700/900 by

following the instructions and illustrations shown below.

Cover removal

1. Remove the power cable from the VSC and from the power

source.

Do not open the cover of the scan converter without

unplugging the power cord.

2. If the VSC scan converter is rack mounted, detach the input

and output cables from it and remove the unit from the

rack. If the VSC is not rack mounted, you do not need to

remove the input and output cables.

3. Remove 14 screws from the top and sides of the cover

(figure 1) of the VSC 900. The VSC 700 has 12 top and side

cover screws plus 9 rear panel screws and 2 jack screw nuts

(RS-232/422 connector).

50/60Hz

100-240V 0.3A

/R-Y

RGB/R-Y, Y,B-Y

RGB

/B-Y

/HV

VVIDEO

S-VIDEO

R/R-Y G/Y B/B-Y H/H-Y RS-232

/422

OUT

Remove #8 Screw

(4 Plcs) Each Side

and Bracket

Remove (14)

Screws

Lift Cover

straight up

Figure 1 — Removing the VSC 900 cover

4. Remove the cover by slightly lifting each side alternately

until the cover is free.

Reverse this procedure to reinstall the cover after the SDI

connector card has been installed.

CAUTION

Do not touch any switches or other electronic

components inside the VSC. Doing so could damage

the scan converter. Electrostatic discharge (ESD)

can damage IC chips even though you cannot feel it.

You must be electrically grounded. A grounding

wrist strap is recommended.

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

VSC 700/900 SDI Output Card • Installation 3

SDI Output Card installation

After following the instructions in “Cover removal” to remove

the cover, do the following:

1. Locate the SDI card standoff located near the middle rear

(VSC 900) or left rear (VSC 700) portion of the main circuit

board (looking from above with the front panel nearest to

you).

SDI card standoff

SDI card connector opening

Figure 2 — SDI card standoff and connector opening

2. Remove the plastic cap covering the SDI connector opening

from the rear panel of the VSC, and position the SDI card at

an angle with the SDI connector protruding from the rear

SDI connector opening.

3. The SDI card has a 20-pin socket on the underside which

must align with the 20 pins on the main circuit board. Be

sure to align the pins properly, in order to prevent bending

the pins, before pressing the SDI card firmly in place against

the standoff. The mounting hole on the SDI card should

now be directly over the standoff.

20-pin socket on

back of SDI card

20-pin connector

on main board

Figure 3 — SDI card situated above pins and standoff

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

4. Insert the card’s installation screw through the SDI card’s

mounting hole, and gently tighten it into the standoff.

Figure 4 — SDI card mounted in place

5. Install the SDI connector’s hex nut from the outside of the

rear panel opening. Keep the SDI card from twisting as the

nut is tightened.

6. Replace the top cover on the VSC, and fasten it with the

screws which were removed in step 3 of the “Cover

removal” section.

7. Rack/furniture mount the scan converter, and reconnect the

AC power cord.

Part Numbers

Extron Part Part Number

SDI Output Card Kit 70-065-02

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

Autres manuels pour VSC 900

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Convertisseur de média

Extron electronics

Extron electronics SMD 101 Manuel utilisateur

Extron electronics

Extron electronics IN1606 Manuel utilisateur

Extron electronics

Extron electronics CVC 300 Manuel utilisateur

Extron electronics

Extron electronics BUC 102 Manuel utilisateur

Extron electronics

Extron electronics DVS 605 Manuel utilisateur

Extron electronics

Extron electronics DDS 100 Manuel utilisateur

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuel utilisateur

Extron electronics

Extron electronics VLD 50 Manuel utilisateur

Extron electronics

Extron electronics VSC 500 Manuel utilisateur

Extron electronics

Extron electronics Emotia Xtreme Manuel utilisateur

Extron electronics

Extron electronics DDS 402 Manuel utilisateur

Extron electronics

Extron electronics Two InpuT VIdeo Scaler IN1502 Manuel utilisateur

Extron electronics

Extron electronics SDI to Analog Video Converter SDI-AVR 100 Manuel utilisateur

Extron electronics

Extron electronics Quantum Ultra Series Manuel utilisateur

Extron electronics

Extron electronics QGE 100 Manuel utilisateur

Extron electronics

Extron electronics DVS 304 Manuel utilisateur

Extron electronics

Extron electronics NAV E 511 Manuel utilisateur

Extron electronics

Extron electronics NAV E 511 Manuel utilisateur

Extron electronics

Extron electronics II Manuel utilisateur

Extron electronics

Extron electronics NAV E 101 DTP Manuel utilisateur

Extron electronics

Extron electronics HAE 100 Manuel utilisateur

Extron electronics

Extron electronics NAV SD 511 Manuel utilisateur

Extron electronics

Extron electronics DVI-RGB 100 Manuel utilisateur

Extron electronics

Extron electronics IN1404XT Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur