Extron electronics PowerCage FOX 4G Rx DVI Manuel utilisateur

This guide provides instructions for an experienced installer to set up and operate the Extron®PowerCage FOX

4G Tx/Rx DVI and PowerCage FOX 4G Tx/Rx VGA ber optic video and audio extenders.

NOTES: PowerCage transmitters (Txs) can output signals to any PowerCage Fox 4G,

FOXBOX 4G, or FOX 500 VGA or DVI device.

PowerCage receivers (Rxs) can accept signals from any PowerCage 4G,

FOXBOX 4G, or FOX 500 VGA or DVI device.

Installation

Step 1 — Mounting

Install the Tx, Rx, or both in PowerCage enclosures as required.

NOTES: • PowerCage boards are hot-swappable.

• Ensure the boards are ush with the

rear of the enclosure and the screws

tightened securely before applying

power.

Step 2 — Input and Output Connections

a. Connect an RGB or DVI video source to the Input connector

on the transmitter.

b. Connect an RGB or DVI display to the Output connector on

the receiver.

c. Connect a balanced or unbalanced, stereo or mono audio

input to the transmitter via the Audio Input captive screw connector and a

balanced or unbalanced stereo or mono audio device to the receiver via the Audio Output captive screw connector. See the drawing

below.

Unbalanced Stereo Output Balanced Stereo Output

Ring

Sleeve(s)

Tip

Ring

Sleeve(s)

Tip

NO GROUND HERE.

Unbalanced Stereo Input Balanced Stereo Input

Ring

Sleeve (s)

Tip

Sleeve

Tip

Sleeve

Tip

Ring

Do not tin the wires!

CAUTION: • For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-)

contacts).

•

Raccordez les manchons à la masse (GND). Ne PAS connecter les manchons aux contacts négatifs (–).

d. If you want the PowerCage FOX 4G units to pass serial data or control signals, such as for serial control of a

RS-232

VER FIBER

Tx Rx

projector, connect the primary device to the transmitter and the secondary device to the receiver via the rst three poles

of the RS-232 Over Fiber captive screw connectors on both units.

NOTE: For RS-232 responses (from the receiver to the transmitter), you must install the cable in step 2d and leave the receiver in

normal conguration.

e. For serial control of the transmitter and receiver, connect a host device, such as a computer, to the Remote RS-232

1 2

REMOTE

RS-232

Tx Rx

ALARM

port on either unit via three poles (Tx, Rx, and _) of the Remote RS-232/Alarm 5-pole captive screw connector on either

unit. The protocol for these ports is as follows:

• 9600 baud • no parity • 8 data bits

• 1 stop bit • no ow control

Refer to the PowerCage FOX 4G Tx/Rx User Guide for detailed information about using the Simple Instruction Set (SIS™) commands

and the Windows®-based FOX Extender program to set up and operate the transmitter and receiver and to take advantage of the

various adjustments and test patterns available on the PowerCage FOX 4G units.

f. For remote monitoring of the status of the Rx optical link on either the transmitter or receiver, connect a locally

1 2

REMOTE

RS-232

Tx Rx

ALARM

constructed or obtained device to the two Alarm poles of the Remote RS-232/Alarm 5-pole captive screw connector on

that unit. The two poles are shorted together when no light is detected.

MONO

AUDIO OUTPUT

SHARP GAIN

Y/VID C

INPUT

PowerCage

MTPR AV

Tx Rx

HD/SDI INPUTHD/SDI OUTPUTS

MODE

PowerCage

FOX3G HD-SDI

1 2

REMOTE

RS-232

OVERFIBER

Tx Rx

ALARM

VIDEO

PowerCage

FOX2G Rx AV

Tx Rx

AUDIO

5A MAX.

100-240V 50/60Hz

1 2

REMOTE

RS-232

OVERFIBER

Tx Rx

ALARM

OUTPUT

RGB

PowerCage

FOX4G RX RGB

Tx Rx

AUDIO

16 available single board slots or

8 double board slots

Power

Supply

Scre

RGB

DVI

PowerCage FOX 4G Tx/Rx DVI and VGA Setup Guide

Step 3 — Throughput Connections

NOTE: See the two ber cable connection drawings below. You can connect the transmitter and one or more receivers in one

of three ways:

• One way (transmitter to receiver) only, perform step 3a.

• Two way (transmitter to receiver and return), perform steps 3a and 3b.

• One way (transmitter to receiver) with daisy chain (receiver to receiver), perform steps 3a and 3c.

a. Connect the ber between the Tx port on the transmitter and the Rx port on the receiver.

b. If you want the receiver to send return serial data (such as responses from a controlled device) to

the transmitter, connect a cable between the receiver’s Tx and transmitter’s Rx ports.

c. If you want a receiver to daisy chain the optical signal to another receiver (up to 10 receivers in a

daisy chain):

• Connect the receiver’s Tx ber cable to Rx on another receiver.

• Set each receiver to daisy chain mode. See Normal and Daisy Chain Modes, below.

om Transmitter

or Daisy-Chained

Receiver

Tx Rx

Step 4 — PowerCage Conﬁguration Port

If desired, connect a host device to PowerCage enclosure Conguration connector via

the 9-pin D to 2.5 mm mini jack TRS RS-232 cable that is included with the PowerCage

enclosure or available separately using part #70-335-01. Repeatedly press the Comm Select

button until the Comm LED lights for the slot where the transmitter or receiver is installed.

The protocol for this port is as follows:

• 9600 baud • no parity • 8 data bits

• 1 stop bit • no ow control

Refer to the PowerCage FOX 4G Tx/Rx User Guide for detailed information about using the

SIS commands and the Windows®-based FOX Extender program to set up and operate the

transmitter and receiver and to take advantage of the various adjustments and test patterns

available on the PowerCage FOX 4G units.

Operation

After all receivers, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems

are encountered, verify that the cables are routed and connected properly and that all display devices have identical resolutions

and refresh rates. If your problems persist, call the Extron S3Sales & Technical Support Hotline at the number shown below that is

closest to you.

Normal and Daisy Chain Modes

The receiver operates on one of two modes:

• Normal mode — The receiver outputs RS-232 and SIS commands and responses on its Tx LC connector.

• Daisy chain mode — The receiver daisy chains its Rx connector input through to its Tx connector output.

Use SIS commands issued to the connected unit to toggle between normal and daisy chain modes. Connect a PC to the

Remote RS-232 port of either unit or to the Conguration port on the PowerCage enclosure and issue the following command:

66*0*n#

where:

n= 2 = enable daisy chain mode

n= 1 or 0 = disable daisy chain mode

NOTE: Up to 10 receivers, each in daisy chain mode, can be connected in a daisy chain to a single transmitter.

Receiver

ansmitter

Tx Rx

and

COMM

POWER

ALARM

COMM

SELECT

CONFIG

Comm

Select

Button

Configuration

Port

Comm

LED

68-1911-50

Rev B

10 20

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

PowerCage FOX 4G Tx/Rx DVI and VGA Setup Guide (Continued)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Extenseur

Extron electronics

Extron electronics FOX T USB Manuel utilisateur

Extron electronics

Extron electronics DDX 102 Tx Manuel utilisateur

Extron electronics

Extron electronics DVI 104 Rx Manuel utilisateur

Extron electronics

Extron electronics FOX 3G HD-SDI Manuel utilisateur

Extron electronics

Extron electronics HDMI 230 D Manuel utilisateur

Extron electronics

Extron electronics DTP DVI 301 Manuel utilisateur

Extron electronics

Extron electronics DTP DVI 330 Manuel utilisateur

Extron electronics

Extron electronics FOX 500 DVI Manuel utilisateur

Extron electronics

Extron electronics XTP T HD 4K Manuel utilisateur

Extron electronics

Extron electronics DTP R HWP 4K D series Manuel utilisateur

Extron electronics

Extron electronics EDID 101H 4K Manuel utilisateur

Extron electronics

Extron electronics DTP T UWP 4K 232 D Manuel utilisateur

Extron electronics

Extron electronics HDMI 230 D Manuel utilisateur

Extron electronics

Extron electronics TP Series Manuel utilisateur

Extron electronics

Extron electronics DTP T DP 4K 330 Manuel utilisateur

Extron electronics

Extron electronics Extender Wall Mount Series Manuel utilisateur

Extron electronics

Extron electronics DTP HDMI 4K D Series Manuel utilisateur

Extron electronics

Extron electronics FOX 2G Tx AV Manuel utilisateur

Extron electronics

Extron electronics Tx-Rx Manuel utilisateur

Extron electronics

Extron electronics FOX3 SR 20 Manuel utilisateur

Extron electronics

Extron electronics FOX T USB Extender Plus Manuel utilisateur

Extron electronics

Extron electronics Extension Kits AVTrac 4C Manuel utilisateur

Extron electronics

Extron electronics DTP DVI 4K 230 D Series Manuel utilisateur

Extron electronics

Extron electronics DTP T 3G-SDI 230 D Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur