Extel AudioGlass 651 Manuel utilisateur
0681
Before starting using the handset, put the
handset on charge during about ten hours.
Without this complete charge, the product
will not work
651
INSTALLATION AND USER’S GUIDE
Wireless door phone
652
AG 651 AG 652
Ed. 02-06 V11
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 40
41GB
WALL
BRACKET
(x2 - AG 652)
HANDSET
(x2 - AG 652)
ROADSIDE
PANEL
INSTALLATION
The transmission range listed was measured in a free field (no obstacles).
The actual range may be shorter depending on the quantity and type of obstacles between or beside the
units.
It is therefore essential to test all system components before installing them in order to determine
the best locations for the roadside panel and the handset.
ACCESSGLASS
ADAPTER
(x2 - AG 652)
1. DESCRIPTION
Important !
- Before starting to test the unit, charge the handset for about 10 hours (see page 44)
- If communication is not established between the handset and the roadside panel, repeat the enti-
re programming procedure (see "selecting a communication code" on page 44
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 41
42GB
2. COMPONENTS
a. Handset (x2 - AG 652)
1. Microswitch compartment. Open to select the audio communication channel with the roadside
panel (3 microswitches to be set with microswitches 2-3-4 on the roadside panel).
2. Multifunction status LED for wireless handset.
Green LED : correctly synchronised with roadside panel
Red: recharge handset battery.
Green/red : change batteries in the Accessglass box on the roadside panel or power supply
problem to Accessglass box.
3. Automatic gate opener control button (operates only if the Accessglass box is connected).
Important : to activate this function, press and hold this button for at least 5 seconds.
4. Electric strike plate or lock control button (operates only if the Accessglass box is connected).
Important : to activate this function, press and hold this button for at least 5 seconds.
5. Speak button (for communication with roadside panel).
6. Handset ‘phone’ antenna.
7. Handset battery compartment.
8. Chime volume control.
9. Charge LED (If LED is off, the handset is incorrectly positioned or not on its base).
10. Socket for 12 V DC adapter.
2
1
3
8
74
5
6
10
9
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 42
43GB
b. Roadside panel - AG 651
1. Speaker : allows callers to hear the person inside.
2 - 3. Nameplate and call button: a chime is heard inside and
outside when this button is pressed.
4. Microphone : for communicating with the person inside.
5. LED lights up to confirm proper connection with the
indoor panel and the right battery level or power supply
connection.
6. Gently lift up the protective plastic cover with a small
screwdriver and slide the card in the slot.
1
3
45
2
6
b. Roadside panel - AG 652
1. Speaker : allows callers to hear the person inside.
2 - 3. Nameplate and call button: a chime is heard inside and
outside when this button is pressed.
4. Microphone : for communicating with the person inside.
5. LED lights up to confirm proper connection with the
indoor panel and the right battery level or power supply
connection.
6. Gently lift up the protective plastic cover with a small
screwdriver and slide the card in the slot.
1
3
4
5
2
6
1 2
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 43
44GB
3. FIND THE BEST LOCATIONS FOR THE HANDSET AND
THE ROADSIDE PANEL
a. Handset
1 Open the compartment and position the battery.
2 Connect the adapter to the handset base.
3 Place the handset on its base.
4 The red charge LED should come on.
5 Leave the handset to charge for at least 10 hours.
1 Open the battery compartment on
the back of the roadside panel.
2 Insert 4 new LR06
AA) batteries
c . Select an AUDIO transmission code (AG 651 & AG 652)
1 Enable programming by setting microswitch 4on the roadside panel to On
and microswitch 1on the handset to On.
2 Set microswitches 2on the roadside panel and the handset to On or Off.
3 Set microswitches 3on the roadside panel and the handset to On or Off
(do not set to ‘Off’ if microswitches 2 are set to ‘Off’).
4 Press the button on the roadside panel. If correctly synchronised, the LED
behind the nameplate will flash green and red.
5 After programming, reset microswitch 4on the roadside panel and micros-
witch 1on the handset to Off.
IMPORTANT : The handset has an autonomy of approximately 8 hours.
If the battery is recharged after becoming fully discharged, it may be neces-
sary to remove the battery from the handset for a few seconds, re-insert it,
and re-program it completely if communication is not restored when charging
is complete (sections 1, 4 and 5).
b. Roadside panel
1 2 3
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 44
45GB
1 To test the roadside panel, place it at a height of 1.6 metres.
2 To test the handset, place it at a height of approximately 1.5 metres on a wall or lay it on a table.
3 Press the call button on the roadside panel. The chime will sound on the handset (adjust the volume if
necessary). To speak, press the button on the handset.
4 Buttons and work only if the ACCESSGLASS box is installed and a connection is made with
the roadside panel.
6 If the quality of the communication is satisfactory, finish the test by moving around with handset.
7 TAKE THE BATTERIES OUT OF THE BACK OF THE ROADSIDE PANEL
8 The roadside panel is powered by the ACCESSGLASS box which also controls an electric strike
plate or lock and an automatic gate opener.
e. Test the locations of the roadside panel and the handset
IMPORTANT : the handsets have an autonomy of approximately 8 hours.If
the batteries are recharged after becoming fully discharged, it may bene-
cessary to remove the batteries from each handset for a few seconds andre-
insert them. If there is still no connection, re-set the video door
phone(points 3, 4 and 5 on pages 5 and 6).
Handset 2 - Right button on roadside panel.
1 Set microswitch 2 on handset 2 to the same configuration as handset 1.
2 Set microswitch 3 on handset 2 to the same configuration as handset 1.
3 Enable programming by setting microswitch 5on the roadside panel to
Onand microswitch 1 on the handset to On.
4 Press the right button on the roadside panel.If correctly synchronised,
the LED behind the nameplate will flash green and red.
5 After programming, reset microswitch 5 on the roadside panel and
micros-witch 1on the handset to Off.
d. Selecting an “AUDIO”transmission code (contd.) (AG 652)
1 2 3
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 45
46GB
6-conductor cable
Terminal blocks on back
of roadside panel
black wire -
no wire + LR20
red wire + DC
green wire D+
brown wire D-
orange wire G+
yellow wire G-
4 ACCESSGLASS
1- Powering the roadside panel.
2- Controlling an electric strike plate or lock.
3- Controlling an automatic gate opener.
Install the module on the back of a pillar. For a cleaner look, route the wires through the pillar.
The 3 metre long cable may be cut to length if necessary.
This module is essential for :
a- Connecting the 6-conductor cable to the roadside panel
ACCESSGLASS MODULE POWERED BY 4 LR20 (D) BATTERIES
(Remember to take out the four LR06 batteries from the roadside panel if present).
6-conductor cable
Terminal blocks on back
of roadside panel
black wire -
red wire + LR20
no wire + DC
green wire D+
brown wire D-
orange wire G+
yellow wire G-
ACCESSGLASS MODULE POWERED BY A 12-24 V AC OR DC SUPPLY
(Remember to take out the four LR06 batteries from the roadside panel if present & LR20).
When wired as above, the nameplate on the roadside panel is lit continuously.
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 46
47GB
- The box comes supplied with a 3-metre cable with 6
colour-coded conductors, a 2-wire output for connec-
ting an electric strike plate or lock, and a terminal block
for an automatic gate opener control.
- These functions are available only when the door phone
is used with the roadside panel.
a- Connect the strike plate or lock to the wires exiting
directly from the box.
b- If installing an automatic gate opener, connect it direct-
ly to terminals ‘G+’ and ‘G-‘ in the box.
This box may be connected to a 12-24 V AC or DC power supply (do
not insert standard or rechargeable batteries in the box in this case).
Connect the external power supply to the ‘-’ and ‘+ 12/24V’ terminals
(connect the ‘+’ to the ‘+ 12/24V’ terminal for a DC supply).
Accessglass mounting holes. Take care not to damage the seal
when refitting the cover.
The ventilation hole
should be at the bottom
(on the base and the cover).
a- Installing in the ACCESSGLASS box
T
T
T
T
Fuse
G-
G+
12V/24V
_
+
AC/DC
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 47
48GB
5. INSTALLING THE DOOR PHONE
a. Installing the handset
1
Handset mounted to a wall
1. Mount the wall bracket .
2. Mount the charger base on the bracket .
3. Plug in the adapter.
1
1
2
2
b. Installing the roadside panel
1. Remove the screw under the roadside panel .
2. Pull the roadside panel forward .
3. Remove the roadside panel .
4. Firmly secure the frame with two screws .
5. Connect the wires as shown on the wiring diagram.
6. Fit the roadside panel back in place and .
7. Put the attachment screw back in place and tighten .
1
2
3 4
5
7
1
2
3
6
4
7
5
6
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 48
49GB
6. SPECIFICATIONS
Handset AG 651 - AG 652 (x2)
Reference : 810651
Kit handset : PACB 651
Supply voltage : 12 V DC
Power consumption : 700 mW
Power adapter AG 651 - AG 652 (x2)
Reference : 830651
230 V / 12 V DC, 200 mA adapter
Roadside panel AG 651
Reference : 820651
Kit roadside panel : PAPL A 651
Operating temperature : -10°C to +40°
Accessglass AG 651 - AG 652
Reference : AG 653
Supply voltage : 6 V, 4 LR20 (D) batteries or 12-24
V AC or DC supply.
Fuse protection : T 1 A-250 V
Roadside panel AG 652
Reference : 820652
Kit roadside panel : PAPL A 652
Operating temperature : -10°C to +40°
Manuel AG 651+652 V11 MU#108C58 3/02/06 9:31 Page 49
Autres manuels pour AudioGlass 651
1
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Extel Système d'interphone
Extel
Extel LUKA Manuel utilisateur
Extel
Extel LENA 18 .2 Manuel utilisateur
Extel
Extel WEVP 440 BIS Manuel utilisateur
Extel
Extel WECR 80515 SER.R1 Manuel utilisateur
Extel
Extel WEPA 201 LC SER.R1 Manuel utilisateur
Extel
Extel LEVO Manuel utilisateur
Extel
Extel TALKLINE 10 Manuel utilisateur
Extel
Extel LESLI Manuel utilisateur
Extel
Extel LILLY DF-PI201 Manuel utilisateur
Extel
Extel WEVPMH001 Manuel utilisateur
Extel
Extel WECR 61004 Manuel utilisateur
Extel
Extel WEVP 251 Manuel utilisateur
Extel
Extel WEVP 628 E BIS Mode d'emploi
Extel
Extel LENA 18 Manuel utilisateur
Extel
Extel WEPAMH 4 Manuel utilisateur
Extel
Extel IRON 2 Manuel utilisateur
Extel
Extel WEPA 245 BIS Mode d'emploi
Extel
Extel diBi Flash White Manuel utilisateur
Extel
Extel LUKA JS-V440N2 Manuel utilisateur
Extel
Extel MOMBO Ed. 12 - 2014 V1 Manuel utilisateur
