EXFO FTB-85100G Manuel utilisateur



Packet Blazer for FTB-500

FTB-85100G

Getting Results

The Summary tab is

automatically displayed

once the test is started.

Select a tab to get

additional test results.

Alarm/Error Injection

Test control buttons are

reconfigured according

to the test application

and status.

The Stop button is

displayed when the

test is running.

1Tap the Alarms/Errors tab.

Tap Inject.

Gives more information on this alarms/errors group.

Hides the alarm/error selection.

Status Bar

Test Control Buttons

Start

Stop

Starts test. Available when the test is not running.

Stops test. Available when the test is running.

Enables traffic generation and starts test. Available with Traffic Gen & Mon.

Save

Load

Saves, loads, imports, exports, and deletes configuration file(s). Available when the test is not

running.

Report Saves, opens, imports, exports, and deletes test report(s). Available when the test is running or

stopped, but the report generation (save) is only possible when the test is stopped.

Laser (on) Indicates that the laser control is on (for at least one Lane for parallel interface); the laser button

has a red border. Tapping this button will turn off the laser (for all Lanes for parallel interface).

Laser (off) Indicates that the laser control is off (for all Lanes for parallel interface). Tapping this button will

activate the laser immediately by emitting an optical laser signal (on all Lanes for parallel

interface).

Reset Clears results, statistics, and logger content. Available when the test is running.

Inject Injects alarms/errors based on settings from the Inject button from the Results - Alarms/Errors tab.

Discover

Remote

Discovers and connects to a remote module that loop back the traffic via Smart Loopback or Dual

Test Set (DTS).

Tes t

Direction

Pattern Synchronization

Power

Clock

Laser

Remote Control

Inject

Non-default OH

Interface/Signal

Link

Remote Connection.

Not available with Intelligent Apps.

Global Indicator Tap anywhere within the global

indicator area to view the

maximized view of these

indicators.

The global indicator displays the pass/fail verdict,

global alarm, timer, and/or test duration.

2Tap to select an alarm/error.

Select the alarm/error to

be injected and its

parameters.

Quick Reference Guide

100/40G MULTISERVICE TEST MODULE

Printed in Canada (2016-11)

P/N: 1070513 Version: 7.0.0.2 For more information,

refer to the user guide.

Fully integrated layer 1/2/3/4 performance assessment of 40/100 Gbit/s Ethernet, SONET/SDH, and Optical

Transport Network (OTN) equipment and network services.

Physical Interfaces

Starting the Application

CFP PORT

Ethernet 40/100 Gbit/s

OTU3, OTU3e1, OTU3e2, OTU4

OC-768/STM-256

Carefully connect optical fiber cables to the transceiver IN (RX) and OUT (TX) ports.

External Clock

Clock Out Low Speed

Clock Out High Speed

From ToolBox, tap the module’s icon.

Selecting,

Configuring,

and Starting

a Test

Tap o n a

test application.

Tap the Modify Structure button to set the basic structure of the test such as

interface/rate, connector, etc.

Tap the interface block to configure the interface/signal parameters. Ensure

that the link is up and the power level (when supported) is present in the status

bar before proceeding to the next step.

For CFP interface, check for the CFP optical validation check mark

indicating that the CFP matches the configured interface/rate.

Tap the protocol block to configure either the frame structure and its

parameters for Ethernet test applications or the embedded signal for Transport

test applications. This block is not present for all tests.

For Intelligent Apps:

For Transport and Ethernet:

Note: For advanced testing, tap the Functions button.

Tap the clock block to configure the clock synchronization.

Tap t h e Start button to start the test.

Tap the test block to configure specific test settings.

This block is not present for all tests.

2Select the basic port parameters or click on More for full settings. Ensure that the link is up

and the power level (when supported) is present in the status bar before proceeding to the

next step.

3Select the basic test parameters or click on More for all settings.

Select the remote operation mode: Dual Test

Set, Remote Loopback, or Manual

Loopback.

Select the basic remote

parameters or click on More for

full settings.

Tap the Start

button to start

the test.

Status Bar

iOptics iSAM

2Tap the desired

port icon.

Tap t h e Start button to

start the test.

3Once the transceiver is

correctly detected ,

select its rate. 4Select the test parameters

and thresholds.

Autres manuels EXFO Équipement de test

EXFO

EXFO AXS-200/610 Manuel utilisateur

EXFO

EXFO FTBx-88000 Series Manuel utilisateur

EXFO

EXFO MaxTester series Manuel utilisateur

EXFO

EXFO FTB-700 Series Manuel utilisateur

EXFO

EXFO FVA-3100 Manuel utilisateur

EXFO

EXFO FOT-10A Manuel utilisateur

EXFO

EXFO MaxTester 630G Manuel utilisateur

EXFO

EXFO FTB-7000B Manuel utilisateur

EXFO

EXFO IQS-2100 Manuel utilisateur

EXFO

EXFO MaxTester series Manuel d'exploitation et d'entretien

EXFO

EXFO FTB-860 Manuel utilisateur

EXFO

EXFO OTH-7000 Manuel utilisateur

EXFO

EXFO FIP-400 Manuel utilisateur

EXFO

EXFO FTB-3930 Manuel utilisateur

EXFO

EXFO FTB-200 Manuel utilisateur

EXFO

EXFO MaxTester 635G Manuel utilisateur

EXFO

EXFO Power Blazer Manuel utilisateur

EXFO

EXFO LTB Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel utilisateur

EXFO

EXFO Optical Explorer OX1 Manuel d'utilisation

EXFO

EXFO RTU-2 Manuel utilisateur

EXFO

EXFO FPM-300 Manuel utilisateur

EXFO

EXFO FTB-3930 Manuel utilisateur

EXFO

EXFO Fiber Guardian FG-750 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur