EXFO FLS-100 Manuel utilisateur

USER GUIDE

OPTICAL POLARIZED

SOURCE

FLS-110

NETWORK TESTING

part of this publication may be reproduced, stored in a retrieval system or

transmitted in any form, be it electronically, mechanically, or by any other means

such as photocopying, recording or otherwise, without the prior written permission

of EXFO Electro-Optical Engineering Inc. (EXFO).

Information provided by EXFO is believed to be accurate and reliable. However, no

responsibility is assumed by EXFO for its use nor for any infringements of patents or

other rights of third parties that may result from its use. No license is granted by

implication or otherwise under any patent rights of EXFO.

EXFO’s Commerce And Government Entities (CAGE) code under the North Atlantic

Treaty Organization (NATO) is 0L8C3.

The information contained in this publication is subject to change without notice.

Trademarks

EXFO’s trademarks have been identified as such. However, the presence or

absence of such identification does not affect the legal status of any trademark.

Units of Measurement

Units of measurement in this publication conform to SI standards and practices.

Version number: 1.0.0

FLS-110 iii

Contents

Certification Information ................................................................................. iv

1 Introduction .............................................................................. 1

Unpacking and Inspection ................................................................................ 1

Conventions ...................................................................................................... 1

Safety Information ............................................................................................ 2

2 Description ................................................................................ 3

LED Status Indicators ........................................................................................ 3

Keypad .............................................................................................................. 3

Connector Panel ............................................................................................... 3

3 Maintenance .............................................................................. 4

Cleaning the Optical Port .................................................................................. 4

Recharging the NiCd Battery Pack ..................................................................... 4

Replacing the 9 V Alkaline Battery .................................................................... 5

Periodic Source Verification .............................................................................. 5

4 Troubleshooting ........................................................................ 6

Finding Information on the EXFO Web Site ...................................................... 6

Contacting the Technical Support Group .......................................................... 7

Transportation .................................................................................................. 7

5 Warranty .................................................................................... 8

General Information ......................................................................................... 8

Liability ............................................................................................................. 8

Exclusions ......................................................................................................... 9

Certification ...................................................................................................... 9

Service and Repairs ......................................................................................... 10

EXFO Service Centers Worldwide .................................................................... 11

A Technical Specifications .......................................................... 12

Certification Information iv

Certification Information

F.C.C. Information to User

This unit has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

unit generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this unit does cause harmful interference to radio

or television reception, which can be determined by turning the unit off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

³Reorient or relocate the receiving antenna.

³Increase the separation between the equipment and receiver.

³Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

³Consult the dealer or an experienced radio/TV technician for help.

Independent Laboratory Testing

This unit has undergone extensive certification testing both internally, at EXFO,

and externally, at an independent, qualified laboratory. All pre-qualification tests

were performed at EXFO while all final tests were performed at UltraTech

Engineering Labs Inc., a renowned test laboratory from Mississauga, Canada. This

guarantees the unerring objectivity and authoritative compliance of all test results.

Information to User

This equipment has been tested and found to comply with the limits for a Class B

digital device.

WARNING

Changes or modifications not expressly approved by EXFO

Electro-Optical Engineering Inc. could void the user’s authority to

operate the equipment.

FLS-110 v

Electro-Optical Engineering

Application of Council Directive(s): 73/23/EEC - The Low Voltage Directive

89/336/EEC - The EMC Directive

Manufacturer’s Name: EXFO ELECTRO-OPTICAL ENG.

Manufacturer’s Address: 400 Godin Avenue

Quebec, Quebec Canada G1M 2K2

(418) 683-0211

Equipment Type/Environment: Industrial Scientific Equipment

Trade Name/Model No.: FLS-110 Optical Light Source

Year of Conformity Assessment: 1997

Standard(s) to which Conformity is Declared:

EN 61010-1:1990 Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use, Part 1: General Requirements

EN 60825-1:1994 Safety of LED products - Part 1: Equipment classifications, requirements, and

user’s guide

EN 55011: 1993 Limits and methods of measurement of radio disturbance characteristics of

industrial, scientific, and medical equipment

EN 50082-2: 1995 Electromagnetic Compatibility Generic immunity standard - Part 2: Industrial Environment

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive and Standards.

Manufacturer

Signature:

Full Name: Stephen Bull, E. Eng

Position: Vice-President Research and

Development

Address: 400 Godin Avenue

Quebec, Quebec, Canada G1M 2K2

Date: February 20, 2007

DECLARATION OF CONFORMITY

Introduction 1

1Introduction

Unpacking and Inspection

The FLS-110 Optical Polarized Source package contains the following standard

items:

³FLS-110 Optical Polarized Source

³Two 9 V alkaline batteries (one installed and one spare)

³AC adapter/charger

³Holster with shoulder strap

³Instruction manual

³Warranty validation card

³Certificate of Quality

³Declaration of Conformity

³Carrying case

Your FLS-110 has been thoroughly inspected before shipment. If any damage has

occurred during transport, or if any item is missing, please notify EXFO immediately.

Conventions

Before using the product described in this manual, you should understand the

following conventions:

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury. Do not proceed unless you

understand and meet the required conditions.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury. Do not proceed unless you

understand and meet the required conditions.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in component damage. Do not proceed unless you

understand and meet the required conditions.

IMPORTANT

Refers to information about this product you should not overlook.

FLS-110 2

Safety Information

Your instrument is a Class 1 LED product in compliance with standard IEC 60825-1

Amendment 2: 2001. Laser radiation may be encountered at the output port.

The following label indicates that a product contains a Class 1 source:

Note: Label shown for information purposes only. It is not affixed to your

product.

CLASS 1

LED PRODUCT

Description 3

2Description

The FLS-110 Optical Polarized Source is a fiber-optic source used with a power

meter to measure power and loss in singlemode fibers, and with a PMD analyzer

such as the FTB-5500 and FTB-5500B for PMD measurements. The unit includes a

LED optical source and a 2 kHz signal generation for fiber identification. The FLS-110

is powered by either the built-in rechargeable NiCd battery pack, the 9 V alkaline

battery, or the AC adapter/charger.

LED Status Indicators

Keypad

Connector Panel

Low NiCd battery pack

AC adapter/charger operation

(blinks when auto-off is activated*)

NiCd battery operation

(blinks when auto-off

is activated*)

9 V battery operation (blinks

when auto-off is activated*)

NiCd

LOW

BAT

SUPPLY

low

high

LEVEL

* Unit powers off after 10 minutes of inactivity

Low output power

source active (lights

up in CW mode,

blinks in 2 kHz mode)

High output power

source active (lights

up in CW mode,

blinks in 2 kHz mode)

low

high

CWon / off

Powers unit on or off

(high output power and

CW mode by default)

Selects low output

power

Selects high output

power

auto 2 kHz

off

Activates continuous

wave (CW) signal

Activates and

deactivates auto-off Activates (2 kHz)

modulated signal

AC adapter/charger input Optical port

FLS-110 4

3 Maintenance

To help ensure long, trouble-free operation:

³Always clean fiber-optic connectors before using them.

³Keep the unit free of dust.

³Clean the unit casing and front panel with a cloth slightly dampened with water.

³Store unit at room temperature in a clean and dry area. Keep the unit out of

direct sunlight.

³Avoid high humidity or significant temperature fluctuations.

³Avoid unnecessary shocks and vibrations.

³If any liquids are spilled on or into the unit, turn off the power immediately and

let the unit dry completely.

The FLS-110 contains no user-serviceable parts. However, the unit contains sensitive

electronic and optical components, and should be handled carefully and stored in its

carrying case when not in use.

Cleaning the Optical Port

To prevent dust and dirt from entering the connector, always replace the protective

cap on the optical port when not in use. Clean the optical port using a lint-free swab

dipped in isopropyl alcohol (98% pure or more) and blow-dry with compressed air.

In case the unit is equipped with a universal interface (option), rotate the connector

adapter counter-clockwise and remove it. You now have access to the ferrule inside

the connector interface. Clean and blow-dry as explained above. Then replace the

connector adapter and rotate it clockwise until it clicks into place.

Recharging the NiCd Battery Pack

The LOW BAT indication is displayed when the instrument switches from the

NiCd battery pack to the 9-V alkaline battery. To recharge the NiCd battery pack,

plug in the AC adapter/charger. A full recharge takes approximately 14 hours. For

maximum efficiency, recharge the battery at room temperature. To extend NiCd

battery life, deplete the battery’s charge completely before activating the AC

adapter/charger.

WARNING

Use of controls, adjustments and procedures for operation and

maintenance other than those specified herein may result in

hazardous radiation exposure.

Maintenance 5

Replacing the 9 V Alkaline Battery

To replace the alkaline battery:

1. Power off the unit and remove it from the holster.

2. Open the battery compartment door located at the back of the unit.

3. Replace the battery (respecting polarity).

4. Close the battery compartment door and replace the holster.

Periodic Source Verification

EXFO recommends that the FLS-110 be sent back to the factory every year for

verification and adjustment.

Recycling and Disposal (Applies to European

Union Only)

³Unless otherwise noted in a separate agreement between EXFO and a

customer, distributor or commercial partner, EXFO will cover costs related to

the collection, treatment, recovery and disposal of end-of-lifecycle waste

generated by electronic equipment introduced after August 13, 2005 to an

European Union member state with legislation regarding Directive 2002/96/EC.

³Except for reasons of safety or environmental benefit, equipment manufactured

by EXFO, under its brand name, is generally designed to facilitate dismantling

and reclamation.

For complete recycling/disposal procedures and contact information, visit the EXFO

Web site at www.exfo.com/recycle.

Recycle or dispose of your product (including electric and electronic

accessories) properly, in accordance with local regulations. Do not

dispose of it in ordinary garbage receptacles.

This equipment was sold after August 13, 2005 (as identified by the

black rectangle).

Table des matières

Autres manuels EXFO Instrument de mesure

EXFO

EXFO IQS-1700 Manuel utilisateur

EXFO

EXFO T100S-HP Series Mode d'emploi

EXFO

EXFO T100S-HP Series Manuel utilisateur

EXFO

EXFO IQS-12008 Manuel utilisateur

EXFO

EXFO LTK-1 Manuel utilisateur

EXFO

EXFO FTB-740 DWOCC Series Manuel utilisateur

EXFO

EXFO T200S Manuel utilisateur

EXFO

EXFO FTB-5800 Manuel utilisateur

EXFO

EXFO IQS-1500 Manuel utilisateur

EXFO

EXFO FLS-5834A Manuel utilisateur

EXFO

EXFO FOT-5200 Manuel utilisateur

EXFO

EXFO IQS-5320 Manuel utilisateur

EXFO

EXFO PPM1 Manuel utilisateur

EXFO

EXFO FTB-1v2 Pro Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

EXFO

EXFO FTB-8100 Series Manuel utilisateur

EXFO

EXFO VFL Manuel utilisateur

EXFO

EXFO PM-1100 Manuel utilisateur

EXFO

EXFO OmniCure R2000 Manuel utilisateur

EXFO

EXFO FTB-5700 Manuel utilisateur

EXFO

EXFO FOT-10A Manuel utilisateur

EXFO

EXFO ETS-1000L Manuel utilisateur

EXFO

EXFO PPM-350B Manuel utilisateur

EXFO

EXFO FTB-1v2 Pro Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Acterna

Acterna MS1400 Manuel utilisateur