Evve Long Range MK Series Manuel utilisateur

Vlierberg 4-06A

3755 BS Eemnes

The Netherlands

Phone: +31 0 85 0441855 (NL)

E-mail: [email protected]om

Web : www.evvelongrange.com

MK-Series

Installation Manual MK-Series 2/24

ABOUT THIS DOCUMENT ........................................................................................................................... 3

ADDITIONAL INFORMATION & RELATED DOCUMENTS ......................................................................... 3

FFC COMPLIANCE ........................................................................................................................................ 2

SUPPORT SERVICES ..................................................................................................................................... 2

SAFETY INSTRUCTIONS ............................................................................................................................... 2

1. PROTOCOL ............................................................................................................................................... 5

2. VIDEOSTREAMS THROUGH CHARM 10CE............................................................................................ 5

2.1 CONNECTING TO THE CHARM ........................................................................................................ 5

2.2 OPERATING IN MULTICAST ............................................................................................................. 5

2.3 RTSP VIDEOSTREAM.......................................................................................................................... 6

2.4 UPDATING SOFTWARE...................................................................................................................... 6

2.5 ADJUSTING IP ADDRESS.................................................................................................................... 7

2.6 CONFIGURING THE CHARM ............................................................................................................. 8

2.7 NTP SERVER ADDRESS ...................................................................................................................... 9

3. PASSTRHOUGH PORT MOXA ............................................................................................................... 10

3.1 INSTALLING NPORT ADMINISTRATOR.......................................................................................... 10

3.2 SEARCHING FOR DEVICE SERVERS OVER A LAN .......................................................................... 10

3.3 ADJUSTING GENERAL SETTINGS.................................................................................................... 11

3.4 CONFIGURING SERIAL COMMUNICATION PARAMETERS .......................................................... 13

3.5 MAPPING COM PORT TO DEVICE .................................................................................................. 15

3.6 CONFIGURATION BY WEB CONSOLE ............................................................................................ 18

4. OPERATING THE CAMERA WITH KEY-BOARD KBD300A................................................................... 19

4.1 USE THE DIFFERENT SPEEDS.......................................................................................................... 19

4.2 SET OR CHANGE END STOPS ......................................................................................................... 20

4.3 ABSOLUTE CONTROLS.................................................................................................................... 20

5. CAMERA OPERATING COMMANDS ..................................................................................................... 21

5.1 CAMERA COMMANDS..................................................................................................................... 21

5.2 LENS COMMANDS........................................................................................................................... 22

6. LASER OPERATING COMMANDS ......................................................................................................... 23

EVVE LONG RANGETM

Installation Manual MK-Series 3/24

For information on the camera installation, please see Installation Manual

MK-Series. This manual is available from the Evve Long Range website at:

www.evvelongrange.com/downloads

ABOUT THIS DOCUMENT

ABOUT THIS DOCUMEN

This manual contains information on the operation and the different

interfaces of the following Evve Long RangeTM products:

2000HD - High Definition Camera System

The information in this manual is subject to change without notice. Please

refer to our website for the latest information.

NOTE: All graphics contained within this document, including screenshots and

other displays, are for reference use only and are subject to change.

embodied in the product described in this manual.

Evve Long RangeTM and Evve International BVTM are trademarkt of BOTHA BV.

Installation Manual MK-Series 2/24

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation. Changes or modifications to this device void the warranty.

High Definition Demonstration Camera Positioning System

Please contact ELR for technical assistance: [email protected] | +31 0 85 0441855 (NL).

Installation Manual MK-Series 3/24

1. Please read these instructions prior to use.

2. Please keep these instructions accessible.

3. Please heed all warnings.

4. Please follow all instructions.

5. Installation should be done only by qualified personnel and conform to all local

codes.

CAUTION: These servicing instructions are for use by qualified service personnel

only.

To reduce the risk of electric shock, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so.

6. Use only mounting methods and materials capable of supporting at least four times the

combined weight of the pan-tilt unit, mounted payloads, and cabling.

7. For outdoor use, use only corrosion resistant hardware to fasten the mount and

payloads (e.g., stainless steel screws).

8. The unit should not be installed in environments that present conditions beyond

the environmental specification of pan-tilt unit. Installation near heat sources such

as radiators, heat registers, stoves, or other apparatus (including amplifiers) can

exceed the unit’s temperature ratings.

9. Refer all servicing to qualified service personnel. If the unit is damaged, remove power

immediately, and contact ELR.

10. A readily accessible power disconnect shall be incorporated into the installation wiring.

11. Only use replacement parts recommended by ELR.

Installation Manual MK-Series 4/24

Installation should be done only by qualified installers and conform to all local codes.

It is the users’ responsibility to ensure that the mounting methods are safe and adequate for

the location.

Use only stainless steel hardware to fasten the mount to an outdoor surface.

All servicing should be performed by qualified service personnel. Procedures in this manual

do not require entry into the housing of the camera positioning system. The unit contains

potential high voltage. It also contains sensitive devices that can be damaged by static

discharge. To reduce the risk of electric shock and damage to the unit by static discharge do

not perform any servicing other that described in these instructions. If the unit is defective,

please contact the Customer Service Department for technical assistance.

Liability: It is the sole responsibility of the installer to provide proper installation in compliance

with all local codes and regulations.

The Evve Long Range products are part of the next generation of Long Range camera systems,

ranging from high-definition (HD) to standard-definition (SD) camera positioning systems. The

systems are IP (Internet Protocol) based with a full function built-in operating system. Operator

functions features are controlled from the On Screen Display (OSD).

A drive system positioned within the MK-2000HD Series camera permits full 360° continuous pan

and 90° tilt movements. The camera systems comply with MIL-STD-18F standards for temperature,

shock, and vibration specifications. For environmental protection the camera systems use an IP67

camera head enclosure and IP66 positioner enclosure.

For more information on specifications and datasheets, please refer to specific product pages at Evve

Long Range website: www.evvelongrange.com/downloads.

At 50km the pixels per meter in

height will be 8. Assuming man is

2m approx. then 8 pixels is

Detection.

At 5km the pixels per meter in

height will be 40. Assuming man

is 2m approx. then 80 pixels is

Identiﬁcation, i.e. it’s a man or

woman.

SAFETY INSTRUCTIONS

CLASS 3 (EYE & SPECULAR REFLECTION HAZARD):

Never aim the laser at a person’s eye or stare at the laser from within the beam.

Keep the beam path above or below eye level for one seated or standing.

Laser safety eyewear is needed if MPE (Maximum Permissible Exposure) is exceeded.

Don’t view beam directly with optical instruments unless a protective filter is used.

Only experienced and authorized individuals are permitted to operate the laser.

Secure the laser from operation by unauthorized personnel. A key switch should be used if

unauthorized personnel may gain access to the laser.

Always strive to enclose as much of the beam path as practical and to operate the laser in a

controlled access area.

During alignment, avoid placing one’s eye near the axis of the beam path, where specular

reflections are most likely to occur. Alignment eyewear should be considered.

Unnecessary specular (i.e., mirror-like) reflecting objects should be removed from the beam

path.

Mount the laser on a firm support to ensure the beam travels along its intended path.

Post laser hazard warning signs at entrances to laser use areas.

Installation Manual MK-Series 5/24

2.1 CONNECTING TO THE CHARM

You need a computer with Ethernet connection to the CHARM, and a web browser. Furthermore,

you need to know the IP address of the CHARM the default is 10.0.0.2.

Open the web browser and enter http://10.0.0.2 where 10.0.0.2 is the IP address of the CHARM.

The username is “v4” and the password “vision4ce”.

2.2 OPERATING IN MULTICAST

Looking at the start screen, towards the middle, you can see the option to ‘Edit’ the template.xml

file. Click the Edit button, and then follow the instructions in the file to:

Copy to another file.

Edit the copied file to:

oRemove the lower case x from the xStreamRTSPCfg0 entry.

oChange the bUseUnicast=”true” to bUseUnicast=”false”.

Save the file.

Ensure that the new file is ‘selected’ in the WebUpdater interface.

This MK-2000HD Series ELR camera has been adjusted to Pelco D 9600 Protocol.

Installation Manual MK-Series 6/24

2.3 RTSP VIDEOSTREAM

To obtain a direct RTSP VideoStream of the charm, use the following URL:

10.0.0.2:8001/charmstream

in which 10.0.0.2 is the IP address of the CHARM10CE.

To get a VideoStream in RTSP, you can a media player like for example VLC.

2.4 UPDATING SOFTWARE

The following instrucitons are for updating the tracker software on a CHARM with Ethernet

connection. Operating system and tracker sofware update over serial connection are not covered

here.

PRE-REQUISITES

You will need a computer with Ethernet connection to the CHARM, an update file and a web

browser. You will need to know the IP address of the CHARM (the default is 10.0.0.2).

PERFORMING AN UPDATE

Choose “Update

CHARM” from

the CHARM Main

Page then click

on the “Choose

file” button and

navigate to the

update file.

Once it has finished uploading you will see

“Processing update …” for a few seconds then

“Running update” and finally the installer output in

the box below or a “connection lost” message

when the CHARM reboots itself after installation.

2. VIDEOSTREAMS THROUGH CHARM 10CE

Installation Manual MK-Series 7/24

2.5 ADJUSTING IP ADDRESS

To change the IP address click on the “Change IP address link” from the CHARM Main Page. Enter

the new IP address and subnet mask. For IP addresses in the 10.0.0.x range the subnet mask

should be 255.0.0.0 and for IP addresses in the 192.168.1.x range the subnet mask should be

255.255.255.0.

You can optionally add a gateway address if you need the CHARM to connect to the internet, to

get internet (NTP) time for instance.

Upon pressing the submit / Set IP button the IP address will be changed and the CHARM rebooted.

To view the CHARM Web Updater again you will need to log in again at the new IP address.

2. VIDEOSTREAMS THROUGH CHARM 10CE

Installation Manual MK-Series 8/24

2.6 CONFIGURING THE CHARM

If you have been provided with additional configuration files by Vision4ce you can select which

one is loaded by the CHARM software.

Select the required configuration file and press the submit / “Set config” button. If the CHARM has

secondary user config files you can also select these. The selected files will be used next time the

CHARM is rebooted. There is a reboot button on the home page.

2. VIDEOSTREAMS THROUGH CHARM 10CE

Autres manuels pour MK Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Evve Long Range Appareil photo numérique

Evve Long Range

Evve Long Range MK-1900HD Series Manuel utilisateur

Evve Long Range

Evve Long Range MK-1900HD Series Manuel utilisateur

Evve Long Range

Evve Long Range MK Series Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur