Evluma ROADMAX Series Manuel utilisateur

ROADMAX®SERIES LUMINAIRES

ROADMAX RX2 LUMINAIRE INSTALLATION INSTRUCTIONS

PLEASE READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

Verify that supply voltage is correct. RoadMax RX2 operates at 120-277 VAC, 60 Hz current.

Do not exceed maximum voltage marked on luminaire label.

LED luminaires should be powered directly from a switched service unless speciﬁcation indicates otherwise.

Do not connect directly to control devices, such as occupancy sensors, timing devices or dimmer packs.

Follow all National Electrical Codes (NEC) and any applicable local code requirements for electrical and

grounded connections. Wiring connections should be capped with UL listed or recognized connectors.

Wear gloves and safety glasses when removing luminaire from carton, during installation, or while performing

maintenance.

Avoid direct eye exposure to an LED light source while in operation.

Disconnect power before wiring the ﬁxture. High voltage may be

present even when the photocell is removed.

If not qualiﬁed, consult an electrician.

PRODUCT DESCRIPTION

The RoadMax RX2 has been listed to

U.S. and Canadian safety standards

CSA per Met Labs. It is suitable for use

in wet locations. Temperature operation

range is -40°C min to 50°C max.

This luminaire is designed for outdoor lighting

purposes. It should not be used in an area with

limited ventilation or an enclosed area with a high

ambient temperature. Store in a dry location prior to

installation. Do not expose luminaire to the weather

without a shorting cap or photocell installed unless

the luminaire has been ordered with the Evluma

integrated photocell.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

TOOLS REQUIRED

• 9/16 in drive socket, or box wrench for tenon bolts

• #2 Phillips screwdriver for photocell receptacle, or

photocell

• 5/16 in drive socket, or 1/4 in slotted screwdriver for

lens, or shields

• 1/4 in slotted, or #2 Phillips screwdriver for conductive

wires

PN-101179-001 REV A01 3600 Lind Ave SW, Suite 140, Renton, WA 98057 425-336-5800 evluma.com

install direction photocell receptacle

access panel knob

access panel mounting arm

If you are installing a secondary lens or light trespass shields, attach to the luminaire prior to hanging the luminaire.

Please see the separate instructions for installing these accessories. Installing a photocell, steps 8 and 9, may be

easier to perform on a workbench than on a pole. Likewise, setting the FAO (Field Adjustable Output switch), step

7, can be done in advance, prior to installation. Please review the entire guide before proceeding.

1. Disconnect power to reduce the risk of electrical shock.

2. Open the access panel using the access panel knob by rotating approximately 2 turns.

3. Using the 9/16 inch drive socket, loosen (do not remove) the two tenon clamp bolts enough to allow the

mounting arm (not included) to slide into the service cavity.

Leveling steps are +/- 5° tilt:

+5, +2.5, 0, -2.5, -5 degrees.

4. RoadMax RX2 accepts mounting arms with a maximum outside diameter of 1-5/8 & 2-3/8 inch.

Luminaire is set at the factory to accept 1-1/4 inch mounting arm.

Mounting arm should be placed upon or ‘stopped’ against the leveling steps.

Use caution and avoid striking internal components with the mounting arm.

Leveling steps are designed to be used in conjunction with the bubble

level to install the luminaire in a straight or level position.

Note: A wildlife guard is provided for use with a 1-1/2 inch diameter mounting

arm or smaller. If using a mounting arm larger than 1-1/2 inches remove the

wildlife guard. See instructions for Installing or Removing the RoadMax Wildlife

Guard.

5. Tighten the bolts to 120 in-lbs, alternating from bolt to bolt. Refrain from tilting the clamp or unevenly

tightening the bolts to avoid cross-threading. Using the bubble level, conﬁrm that the luminaire is level.

6. Pull the wires through the mounting arm. Allow for enough length to easily attach to the three-position

terminal block. Loosen the terminal block screws prior to connecting wires. Use 1/4 inch slotted, or #2

Phillips screwdriver for securing conductive wires in the terminal block, torque to 15 in-lbs.

a. Connect the green wire, or ground, to the terminal block at the GND location.

b. Connect the black wire, or hot, to the terminal block at the L1 location.

c. Connect the white wire, or neutral, to the terminal block at the L2(N) location.

Note: A reference wiring diagram can be found inside the access panel. RoadMax is sold with pigtail

options. Exact steps may vary depending on if pigtails (white, black and green wires) are sold with the

luminaire vs. a no pigtail option.

ROADMAX®RX2 INSTALLATION INSTRUCTIONS

INSTALLING THE ROADMAX RX2 LUMINAIRE

dia. 2-3/8

REAR VIEW

wildlife guard

dia. 1-5/8

-5

-2.5

+2.5

7. If you have ordered a luminaire with an FAO (Field Adjustable Output switch) installed and you intend to

use this to set a lower wattage, do so at this time if you have not done so already. Please refer to the RX2

datasheet for details.

8. Rotate the photocell receptacle if position requires adjustment. By default, North is oriented to the front of

the luminaire. Use a #2 Philips screwdriver for photocell receptacle or photocell only if rotation is

required. Torque to 25 in-lbs.

9. Insert a twist lock photocell (not provided) or network node (not provided) into the photocell receptacle

and install in accordance with the manufacturer’s instruction.

Note: Before installing a node on an RX2 with an F7 receptacle conﬁguration, please contact Evluma

Customer Support at customercar[email protected] for additional instructions and reference the wiring

diagram located on the inside of the access panel.

10. Close the access panel. Tighten the access panel knob. Do not over tighten.

11. With power on, test the photocell.

Note: Photocells and photocell test response times may vary. Some photocells may turn the

light off and on over the ﬁrst few minutes after power is applied. This does not indicate a defect. A

defective photocell will operate with the light on at all times regardless of the time of day. Allow several

minutes for the photocell to turn the ﬁxture off. A small number of photocells fail off. Test according

to the type of photocell in use.

If the luminaire comes with the Evluma integrated photocell, “XP” model, allow up to 5 seconds for the

luminaire to respond.

PHOTOCONTROL FAILSAFETM

If the RoadMax has been ordered with Photocontrol Failsafe the luminaire will ﬂash once to indicate that power is

connected, and luminaire is in operation. The RoadMax begins collecting data immediately. Short daytime tests of

the photocell will not affect the gathering of this data.

WARRANTY

Warranty information may be found at evluma.com.

Components inside the ﬁxture are not serviceable.

change. MET labs logo is a registered trademark of MET labs.

NEED ASSISTANCE?

Please feel free call us at 425-336-5800 M-F, 8am- 4pm PST, or email [email protected].

Table des matières

Autres manuels Evluma Lanterne

Evluma

Evluma ROADMAX Series Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur