Evermount EM-P3 Manuel utilisateur
EM P INSTALLATION GUIDE-3
Universal Large Size Tilt Wall Mount
Features
• For LCDs and Plasmas 50" to 72"
• Maximum load: 250 lbs
• Adjustable tilt from -15º to +15º
• Mounts 2.5" from wall
• Solid steel construction
• Safety lock security feature
• Offers side to side movement
WARNING
•
THE WARRANTY WILL ONLY BE VALID IF YOU FOLLOW THE INSTRUCTIONS CAREFULLY
•
If you do not understand the instructions, or are not sure you can follow them safely, contact a
qualified contractor
•
Improper installation may cause serious injury and/or damage. It is recommended that a qualified
contractor install the EM-P3
• Make sure that the wall you plan to use will safely support four times the combined weight of the
mounted equipment, including its accessories
• Under no circumstances should this product be mounted to metal studs.
• Never exceed the maximum load capacity of 250 lbs
• A second person will be required to assist with several steps
• Visit www.everik.com or call 1-866-604-6966 for assistance
• Read this entire document before commencing the installation
Required tools for installation
•
Stud finder
•
Phillips screwdriver
• Wrench
• Drill bit, 6 mm diameter
• Masonary drill bit, 10 mm diameter ( for concrete installation only)
• Power drill
• Socket wrench 13 mm
TABLE OF CONTENTS
Installation tools....................................................................
Parts list................................................................................
Mounting to triple stud wall...................................................
Mounting to concrete or cinder block....................................
Installing monitor brackets....................................................
Mounting the flat panel to the wall........................................
2
3
4
5
6
8
2
A
B
C
D
J
IK
L
E
F
G1/G2
M
H
Description Qty.
AWall plate 1
I
Spacer 4
M
DSquare head bolt 9
EWall anchor 9
Ø8 mm washer 9
Screw M8 x 25 mm 4
Screw M8 x 45 mm 4
Screw M10 x 25 mm 4
Screw M10 x 45 mm 4
Ø10 mm washer 4
Square washer 4
F
G2
H
J
K
BLeft monitor bracket 1
CRight monitor bracket 1
L
Parts List
3
N
Template 1
N
Screw M6 x 16 mm 4
G1
UPUP
Installation to Triple Wood Stud Wall
Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the
edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their
edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template or use
the included part (DD). Level plate, and mark the center of the nine mounting holes. Make sure that
the mounting holes are on the stud center lines. Drill nine 1/4"(6 mm)diameter holes 70 mm deep.
Make sure that the wall plate is level, secure it using nine bolts (M) and nine metal washers (L) as
shown in figure 1.1.
4
AA
M
L
fig. 1.1
•Installermustverifythatthesupportingsurfacewillsafelysupportthecombined
•loadoftheequipmentandallattached hardwareandcomponents.
•Tightenwood screws so that wall plate is firmly attached, but do not overtighten.
•Overtighteningcandamage the screws, greatly reducing their holdingpower.
•Never tighten in excess of 80 in•lb (9 N.M.).
•Make sure that mounting screws are anchored into the center of the stud. The use of
•an "edge to edge" stud finder is highlyrecommended.
•Hardwareprovided is for attachment of mount through standard thickness drywallor
•plasterinto wood studs. Installers are responsibleto provide hardware forother types
•ofmounting situations.
Installation to Solid Concrete or Cinder Block
1) Using the wall plate or included template (DD), make sure it is level and mark nine mounting hole
locations.
2) Drill nine 3/8" (10mm) diameter holes to a minimum depth of 84 mm.
3) Insert anchors (N) in holes flush with wall as shown in figure 1.2a. Place wall plate over anchors
and secure with nine metal washers (L) and screws (M) as shown in figure 1.2b. Verify plate is
level and tighten all the fasteners.
5
•When installing wall mounts on cinder block, verify that you have a minimum of
•1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors.
•Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally
•1" minimum from the side of the block. Cinder block must meetASTM C-90
•specifications. It is suggested that a standard electric drill on slow setting is used to
•drill the hole instead of a hammer drill to avoid breaking out the back of the hole when
•entering a void or cavity.
•Concrete must be 2000 psi density minimum. Lighter density concrete may not hold
•concrete anchor.
•Installermustverifythatthesupportingsurfacewillsafelysupportthecombined load
•oftheequipmentandallattached hardwareandcomponents.
•Always attach concrete anchors directly to load bearingconcrete as shown below.
• Neverattachconcreteanchorstoconcretecovered withplaster,drywall, or other
•finishingmaterial.If mountingto concretesurfacescoveredwitha finishing surface is
•unavoidable,thefinishingsurface must be counterboredas shown in fig. 1.4. Be sure
•concrete anchorsdo notpull awayfromconcrete whentightening screws. If
•plaster/drywall is thicker than 5/8",custom fasteners must be supplied by installer.
concrete
surface
1
3
2
N
Drill holes and insert anchors (N).
Place plate (AA) over anchors (N) and secure with screws (M)
and washers(L).
Tighten all fasteners.
AA
N
ML
WEIVYAWATUC
INCORRECT CORRECT
wall
plate
plaster/
drywall
concrete wall plate concrete
plaster/
drywall
fig. 1.2a
L
M
AA
N
e
t
e
r
c
n
o
c
d
i
l
o
sk
c
o
l
b
r
e
d
n
i
c
fig. 1.2b
Installing Monitor Brackets
BB
CC
CENTERBRACKETS
VERTICALLYONBACKOF
SCREEN
X
X
fig 2.1
6
1) Make sure the flat panel display is not plugged in.
2) With the help of an assisitant ensure the flat panel display is supported while providing
access to the rear of the unit.
3) If screen has knobs on the back, remove them to allow the monitor brackets to be attached.
4) Place monitor brackets (BB and CC) on back of screen, align to holes, and center on back of
screen as shown in figure 2.1.
5) Attach the monitor brackets to the back of the screen using the appropriate combination of
screws, square washers, and spacers as shown in detail in figure 2.2 of the next page.
Notes:
● Top and bottom holes must always be used
● Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver
● Thenumber of fastenersused will varydepending upon the typeofscreen
● "X" dimensions should be equal
Installing Monitor Brackets
7
Screws
F or G or H or I Spacers are required
for recessed mounting
holes (J). Place spacers
between panel and
brackets
Use Square washer(K)
when using 8 mm
screws (F,G) and Ø10
mm washer(K) when
using 10 mm screws
(H,I)
fig 2.2
BB
CC
K
• Tighten screws so monitor brackets are firmly attached. Do not tighten with excesive
• force. Overtightening can cause stress damage to screws, greatly reducing their • • •
dholding power and possibly causing screw heads to become detached. Tighten to 40
• in•lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out
• and bracket is still not tightly secured, damage may occur to screen or product may •
• fail. Verify the correct fasteners are being used and if any doubt remains, contact a
professional installer.
Mounting:
Mounting and Removing Flat Panel Screen
Hook monitor brackets (BBand CC)onto wall plate (AA).3.1as shown in fig and in
.3.2.fig Tighten the tension knobs and optionally padlock the monitor bracket arms to the
.security brackets
:Removing To remove screen from mount rotate the lock knobs of,monitor brackets (BBand CC)
asshown in fig a
.3.2 .
Tension Knob:
The tension knob can
be pulled out and
turned using a ratchet
motion in order to
adjust the tilt as
shown in fig a.3.2 .
fig.3.1
fig.3.2
(Attaching the monitor with monitor
brackets to the wall plate on the wall.)
TENSION KNOB
Tension
Knob
fig a.3.1
fig a.3.2
8
Always use an assistant to safely lift and position the flat panel display.
Security bracket
mc
GUIDE D’INSTALLATION DU SUPPORT
EM P-3
Support de fixation universel inclinable de grande dimension
Caractéistiques
• Pour ranséc ACL 50 72et plasma de po poà
• Charge maximum lb: 250
• Inclinaison ajustable de –15˚ à +15˚
•’ àS nstalle po du muri 2,5
• Fabrication d’acier solide
• Dispositif de verrouillage s uritaireé
• Permet de d lacer lat alement l’ cranéé é
AVERTISSEMENT
•
LA GARANTIE NE SERA VALIDE QUE SI VOUS SUIVEZ LES INSTRUCTIONS CI-DESSOUS À
LA LETTRE.
•
Si vous ne comprenez pas les instructions, ou si vous êtes incertain(e) de pouvoir les suivre de
façon sécuritaire, communiquez avec un entrepreneur-charpentier qualifié.
•
Une installation incorrecte du support peut causer des blessures corporelles graves ou des
dommages sérieux. Nous vous recommandons de le faire installer par un entrepreneur-charpentier
qualifié.
• Assurez-vous que le mur que vous prévoyez utiliser puisse supporter quatre fois le poids combiné
de l’équipement installé, y compris ses accessoires.
• Vous ne devez en aucun cas installer ce produit sur des montants en métal.
• Ne dépassez pas la capacité maximum de la charge de 250 lb.
• Vous aurez besoin qu’une deuxième personne vous aide avec quelques-unes des étapes de
l’installation.
• Visitez www.everik.com ou appelez 1-866-604-6966 si vous avez besoin d’assistance.
• Veuillez lire tout ce guide avant de procéder à l’installation.
Outils requis pour l’installation
•
Chercheur de montant
•
Tournevis Phillips
• Clé
• Mèche de perceuse, diamètre de 6 mm
• Mèche de maçonnerie, diamètre de 10 mm (pour l’installation sur du ciment seulement)
• Perceuse électrique
• Clé à douille de 13 mm
TABLE DES MATIÈRES
Outils requis pour l’installation..............................................
Liste des pièces....................................................................
Installation sur un mur à trois montants................................
Installation sur un mur de ciment ou de blocs de béton.......
Installation des supports du moniteur...................................
Installation de l’écran plat au mur.........................................
2
3
4
5
6
8
2
Table des matières
Langues :
Autres manuels Evermount Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
