EverFocus EHD525EX Manuel utilisateur

EHD525EX

1/3”

Color

Rugged

Dome

True

Day/Night

Camera

1/3” Color Rugged Dome True Day/Night Camera

with

EXView

Sensor

with EXView Sensor

User’s Manual

and

Operation Instructions

Notice

This manual is presented to the users of EHD525EX series by EverFocus

Electronics Corp. With years of engineering researches, EverFocus has

spared no effort to provide the high quality products to the worldwide users.

For the policy of continual product improvement, EverFocus reserves the

right to make changes to the product specifications and documentation

without notice. All the components of the products, including accessories,

components, and outlook, are based on the agreements of each deal to satisfy

all kinds of users. Meanwhile, please be advised that every step of operation

must follow the instruction of this manual to keep EHD525EX series working

under the best condition. Please notice that EverFocus will not be charged

any claims or renewing cases resulted from inappropriate operation.

Table of Contents

Safety Warning ……………………………………. 1

Introduction………………………………………... 2

Specifications………………………………………..3

Installation Instructions…………………………… 4

Dip Switch Functions……………………………… 11

Simple Instructions for the Desiccant Pack……… 13

Safet

Warnin

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TVs, radio transmitters, magnets,

electric motors, transformers, and audio speakers as the magnetic

fields generated from these devices will distort the video image.

2. Do not install the camera in a high temperature environment.

Install camera away from stoves or other heat generating devices

as the high temperature could cause deformation, discoloration or

other damage to the camera. Install the camera where the

temperature range will stay between -40 ~ 122 degree Fahrenheit.

3. Never face the camera towards the sun.

Never aim the camera at the sun or other extremely bright objects

whether it is in use or not.

4. Cleaning

Do not touch the surface of CCD sensor by hand directly. Use a

soft cloth to remove the dirt from the camera body. Use lens tissue

or a cotton tipped applicator and ethanol to clean the CCD sensor

and the camera lens. When the camera is not in use, put the cover

cap on the lens mount.

5. Heater

Heater elements can be very hot! Heaters are located inside the

camera housing and will activate automatically while the

environment temperature is below 50 degrees Fahrenheit. Do not

touch the heater element while it’s active.

Introduction

The most technically advanced EHD series are the newest vandal-resistant

Color Rugged Dome Camera from EverFocus Electronics. The Color Rugged

Dome Camera can withstand a blow from a 10-pound sledgehammer and has a

built-in heater that allows for operation in low temperatures. It is perfect for

all high-profile crime-prone applications such as building entrances, retail

stores, and shopping malls. The extremely durable EHDseries are

unquestionably one of the world's toughest cameras and is your best choice for

vandal resistance. The EHD525EX is designed with True Day/Night function

that allows removable Auto IR Cut and an enhanced B/W sensitivity, while

turning the image from color to B/W.

Main Features for EHD525EX:

zHigh sensitivity designed with 2nd generation SONY EXView sensor.

zSensitivity increases more than 40% compared to other high resolution

sensors

zRevolutionary integrated 10-bit Digital Signal Processor (DSP)

delivers excellent picture quality and performance.

zLow light sensitivity of 0.1 lux/F=1.2 is achieved by using the

advanced 1/3” interline transfer color EXView CCD.

zThe electronic shutter and AGC allow the camera to be used in

environment with varying light levels.

zDC 12V or AC 24V switches automatically power supply; Line Lock

for AC 24V.

zS/N Ratio reaches 52 dB or more.

zIR Vari-focal lens with IR Cut Removable module available.

zTrue Day & Night function.

zCompact size: 5.1” (W) x 3.9” (H) x 5.1” (D).

zZinc base; polycarbonate shell withstand the impact of 10 pounds

sledgehammer, smoke color or clear cover as option.

zUnique security screw lock.

zOperating temperature: -40 ~ 122 degrees Fahrenheit.

zHeater triggered when temperature is less than 50 degree Fahrenheit.

ecifications

Model: EHD525EX

Pickup device: SONY 1/3” interline transfer color EXView CCD

Picture element: NTSC: 768(H) × 494(V)

PAL: 752(H) × 582(V)

Horizontal Resolution: 520 TV Lines

Sensitivity: 0.1 lux / F=1.2

S/N ratio: >52dB(AGC off)

Vari-Focal Lens: 3.6-9mm / 9-22mm IR Lens

IR Cut Removable: Yes (Auto IR Cut Removable and B/W Sensitivity

Enhanced)

Weatherproof Ratings: IP66

Electronic shutter: Up to 1/100,000

IRIS Control: Auto

Auto white balance: YES

Auto gain control: ON/OFF switch

Back light comp.: ON/OFF switch

Line Lock: ON/OFF switch for 24VAC

Flickerless: ON/OFF switch

Gamma correction: 0.45

Video output: 1.0Vp-p, 75ohm

Power source: 12V DC+/-10%, 24VAC+/-10%

Power Consumption: 5W Max. (15W when heater active;

thermostatically controlled)

Sync. mode: Internal Sync. /Line lock (Only for AC24V)

Dimension: 5.1” (W) x 3.9” (H) x 5.1” (D).

Heater auto activated

temperature: 50 degree Fahrenheit

Operating temperature: -40 ~ 122 degrees Fahrenheit, 20~80%

Weight: 3.7 lbs

Installation Instructions

1. Loosen the 4 fix screws on the housing cover by using the provided

wrench (Figure 1). Carefully uncap the housing cover as the direction

shown below (Figure 2); please pay attention not to damage the lens. To

remove the housing cover, push the hinges to the bottom of the bracket,

the hinges can be easily removed from the bracket.

Figure 1

Figure 2

2. Remove the camera.

Vari-Focal Lens

Locking Screws

Heater

Figure 3

To remove the camera, first unplug the wire connection on the back of

the camera. Then loosen the 2 locking screws on the camera base, push

the camera base to the right (toward heater direction, as shown in Figure

3), remove the camera from the mounting base. Reinstall the camera and

the cable while the base mounting is completed.

3. Mounting the base.

Attach the base to the wall or ceiling; fix the base by the 4 setscrews

provided in the accessory pack. The dome weight is approximately 3.7 lbs,

please make sure if the mounting is strong enough to support the weight.

If not, please reinforce the mounting according to the environment.

Note: The diameter of the screw hole is 4.7mm.

Caution: To prevent moisture leaking into the housing, apply an

appropriate gasket or sealant around the conduit connection.

Conduit plug setscrew

Side conduit entry

Back conduit entry

Mounting Setscrew

Figure 4

The camera comes with a conduit plug

pre-installed in the PF 1/2 conduit entry

on the side. The screw can be removed

and installed in the back conduit entry.

Loosen the conduit plug setscrew (as

shown in Figure 5) before removing the

conduit plug.

Side conduit entry (PF1/2)

Figure 5

Back conduit entry (PF1/2)

Conduit plug

4. Re-assemble Camera

I. When mounting COLOR RUGGED DOME CAMERA on the

wall, please aim the “Wall” in line with the triangle “S” marked

on the lead frame. (Factory default)

II. When mounting COLOR RUGGED DOME CAMERA on the

ceiling, please aim the “Ceiling” in line with the triangle “S”

marked on the lead frame.

“Wall”

Figure 6-1

“Ceiling”

Figure 6-2

5. Wire Connection

Connect the power supply cable (AC24V/DC12V), video output and

alarm output to the proper connectors shown as Figure 7.

The V. Phase adjustment screw is located on the termination board.

The vertical phase may require adjustment to synchronize the vertical

phase of the camera with other cameras in the system when it is to be used

in the line-lock sync mode. Make sure the vertical phase adjustment of

the camera does not match other cameras.

Note: The inner part of power plug is positive. The pigtail wire with the white

stripe is positive.

Termination Board

Micro Switch for Alarm trigger

Video

Alarm COM GND

Alarm NO Alarm NC

Power In (+)

Power In (-)

V. Phase Adjustment VR

Figure 7

Autres manuels pour EHD525EX

Table des matières

Autres manuels EverFocus Caméra de sécurité

EverFocus

EverFocus EZ430 Manuel technique

EverFocus

EverFocus ECD900B Manuel utilisateur

EverFocus

EverFocus PoleStar EQ550 Manuel utilisateur

EverFocus

EverFocus EMW430 Manuel utilisateur

EverFocus

EverFocus EMD935F Manuel utilisateur

EverFocus

EverFocus 1/3" B/W CCD Camera None Manuel utilisateur

EverFocus

EverFocus Speed Dome EPTZ3100 Manuel utilisateur

EverFocus

EverFocus ED200E Manuel utilisateur

EverFocus

EverFocus EMD990F Manuel utilisateur

EverFocus

EverFocus EZH5040 Manuel technique

EverFocus

EverFocus EPN Series Manuel utilisateur

EverFocus

EverFocus EPD200A Manuel utilisateur

EverFocus

EverFocus EZ730 Manuel utilisateur

EverFocus

EverFocus EHA2880 eZ.HD Series Manuel utilisateur

EverFocus

EverFocus EZH5040 Manuel technique

EverFocus

EverFocus Speed Dome EPTZ500 Manuel utilisateur

EverFocus

EverFocus EZ-630 Instructions d'installation

EverFocus

EverFocus EPN3600 Manuel utilisateur

EverFocus

EverFocus ED700W Manuel utilisateur

EverFocus

EverFocus M107-N501-001 Manuel utilisateur

EverFocus

EverFocus eZ.HD Series Manuel utilisateur

EverFocus

EverFocus EMN Series Manuel utilisateur

EverFocus

EverFocus M117-N701-001 Manuel utilisateur

EverFocus

EverFocus EPN3600 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur