EverFocus ED300 Series Manuel utilisateur

ED300 Series

User’s Manual

and

Operation Instructions

Version 1.1

Notice

This manual is presentED300 to the users of ED300 by EverFocus Electronics Corp.

With years of engineering researches, EverFocus has sparED300 all efforts to

provide the high quality products to the worldwide users. For the policy of

continual product improvement, EverFocus reserves the right to make changes to the

product specifications and documentation without notice. All the components of

the products, including accessories, components, and outlook, are bas ED300 on the

agreements of each deals to satisfy all kinds of users. Please be advis ED300 that

every step of operation must follow the instruction of this manual to keep ED300

working under the best condition. Please notice that EverFocus will not be

chargED300 any claims or renewing cases resultED300 from inappropriate

operation.

Table of Contents

Safety Warning...............................................................................1

Introduction....................................................................................3

Specification...................................................................................4

Major Parts Names and Functions...........................................5

Installation Instructions ............................................................7

Lens Adjustments.......................................................................8

Adjustments................................................................................9

Safety Warning

1. Do not expose the camera to humidity and dust.

Moisture can damage the camera and cause the danger of electric shock.

If the camera is mountED300 outdoors, a camera housing is

requirED300. Do not install the camera at where there is greasy smoke

or steam, where the humidity is too high, or where there is a lot of dust

to prevent damages to the camera.

2. Do not disassemble the camera.

Do not disassemble the camera body as it is dangerous and may cause

the damages to the camera. Refer all servicing to qualifiED300 service

personnel.

3. Handle the camera with care.

Be careful when handling the camera, do not drop it or subject it too

strong shock or vibration to prevent any damages to it.

4. Do not install the camera near electric or magnetic fields.

InstallED300 the camera away from TV, radio transmitter, magnet,

electric motor, transformer, audio speakers because the magnetic fields

generate from above devices will distort the video image.

5. Do not install the camera in the high temperature environment.

InstallED300 the camera away from stoves, or other heat generating

devices, or where it could be subject to direct sunlight as the high

temperatures could cause deformation, discoloration or other damages of

the camera. Install the camera at where the temperature range will stay

between 0℃to 50℃(32℉to 122℉).

6. Cleaning

Use a soft cloth to remove the dirt from the unit. Use lens tissue or a

cotton tippED300 applicator and ethanol to clean the camera lens.

Introduction

The High Resolution Dome Camera Series are compact, full

functionED300 CCD Color Cameras. Their stylish appearance can be

appliED300 as per installer's ideal locations on the ceiling. The dome

camera designED300 with advancED300 digital processing curcuitry for

high resolution 1/3" color interline transfer CCD sensor, it has DIP switch

for AGC on/off, BLC on/off. The dome camera uses a vari focal auto iris

lens for discreet surveillance or close-up viewing and it features with iris

LEVEL volume control for the best viewing quality.

Main Features:

??DesignED300 with advancED300 digital signal processing circuitry for high

image quality.

??The high sensitivity of 1.42 lux / F=1.6is achievED300 by high-resolution 1/3”

Interline transfer CCD.

??Built-in Vari Focal type, mechanical auto iris lens

??Able to adjust the viewing range with manual zoom lens. c

??With manual PAN/TILT mechanism.

??BLC and AGC function on/off switchable.

??Compact size : 108mm O.D. x 80mm H.

??System available for NTSC or PAL

Specification

Pickup device: 1/3" Interline transfer CCD

Video format: NTSC/PAL

Scanning system: NTSC: 525 TV lines, 60 fields/sec; PAL: 625 TV lines, 50 fields/sec.

Picture elements: NTSC: 811(H) x 508 (V); PAL: 795 (H) x 596 (V)

Effective picture elements:

NTSC: 768 (H) x 494 (V); PAL: 752 (H) x 582 (V)

Horizontal resolution: 480 TV lines

Sensitivity: 1.42 lux / F=1.6

S/N ratio: > 48 Db

Varifocal lens: manual zoom and focus adjustment, mechanical auto IRIS

IRIS level: Adjustable

Back light comp.: On / Off Switch

Auto Gain Control: On / Off Switch

Auto white balance: Yes

Gamma correction: 0.45

Monitor output pin: Yes, 1.0 Vp-p / 75 ohm, test point pin

Video output: 1.0Vp-p/75ohm

Sync. mode: Internal sync.

Audio Available for model High Resolution Dome A

Power source 12VDC or 24VAC, 300mA

Dimension: 108 mm O.D. x 80 mm H

Operating temperature: 0oC to +50oC/20~80%

Power consumption: 5W max.

Major Parts Names and Functions

《ED300》《ED300-A》

?Camera Cover

This cover will protect the camera from dust

and damage.

?Lens

This Vari-

Focal Lens allows users to adjust

the Zoom and Focus manually.

?Base

The c

amera unit is set in the dome base when

it is shippED300 from the factory.

?Focus Ring

To set the focus, loosen the Focus ring knob

first, then turn the ring toward <∞

> or <N>

as necessary. When the focus is

obtainED300 as desirED300, tighten the

focus ring knob.

?Zoom Ring

Loosen the zoom ring knob, then you can

adjust the viewing range. Turn the ring

towards <W> for WIDE or <T> for TELE as

necessary. When the setting is

finishED300, tighten the zoom ring knob.

?Auto Gain Control on/off switch.

The factory setting is AGC on.

?Back Light Compensation on/off

switch

The factory setting is BLC off.

?Level Volume Control

The iris level control for the lens.

?Ground Pin

For monitor use. Please see ?.

?Monitor Pin

When setting up the camera,

connect a

monitor to this video output pin and to the

GROUND pin using alligator clip cables, then

using the image displayED300 on the monitor,

set the surveillance angle.

Power input

Use the connector to connect with 12VDC

or 24VAC-power adaptor.

Video Output BNC Connector

Use the connector to connect with the video in

connector of a monitor.

Installation Instructions

1. Remove the plastic dome cover.

2. Lossen the two screws of the supporting bracket to remove the camera

body.

3. Using four screws to fix the camera base on the ceiling.

4. Put the camera body back to the supporting bracket, then tighten the two

screws to fix the camera.

5. Connect the BNC connector of the camera to a color monitor, or other

video device through a 75 ohm type coaxial cable with BNC female

connector at cable extension.

6. Connect the DC+12V or 24VAC regulatED300 power source of the

camera (DC Jack) to the DC12V or 24VAC Power-in jack with 2mm,

center+, outer-plug.

7. Connect the audio output connector of the camera(model High

Resolution Dome A) to the audio in connector of the monitor.

NOTE: Be very careful not to scratch or damage the lens while making any kind

of setting.

Autres manuels pour ED300 Series

Table des matières

Autres manuels EverFocus Caméra de sécurité

EverFocus

EverFocus EHN3200 Manuel utilisateur

EverFocus

EverFocus EDN1220 Manuel du propriétaire

EverFocus

EverFocus EBD431e Manuel utilisateur

EverFocus

EverFocus ED700W Manuel utilisateur

EverFocus

EverFocus eZ Tracker EFN3320 Manuel utilisateur

EverFocus

EverFocus EMD935F Manuel utilisateur

EverFocus

EverFocus EZ-PLATECAM2-002 Manuel utilisateur

EverFocus

EverFocus EQ120 Manuel utilisateur

EverFocus

EverFocus EDH5210 Manuel du propriétaire

EverFocus

EverFocus EI220 Manuel utilisateur

EverFocus

EverFocus Speed Dome EPTZ500 Manuel utilisateur

EverFocus

EverFocus EZ350 Manuel utilisateur

EverFocus

EverFocus EDH5240 Manuel utilisateur

EverFocus

EverFocus EZ610 Manuel utilisateur

EverFocus

EverFocus WDII EQ600 Manuel utilisateur

EverFocus

EverFocus EBD430/MV2 Manuel utilisateur

EverFocus

EverFocus eqn2200 Manuel utilisateur

EverFocus

EverFocus eZ.HD Series Manuel utilisateur

EverFocus

EverFocus ED100 Series Manuel utilisateur

EverFocus

EverFocus EZA2580 eZ.HD Series Manuel utilisateur

EverFocus

EverFocus ED310e Manuel utilisateur

EverFocus

EverFocus M107-N501-001 Manuel utilisateur

EverFocus

EverFocus EZ430 Manuel technique

EverFocus

EverFocus EPTZ3150 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur