○
9USB ports
This port is for connecting the USB storage device or USB printer.
Note:
This port cannot be connected to USB host devices such as computers.
Do not connect to more than one USB printer at the same time.
Only USB storage devices in FAT and FAT32 formats are supported.
○
10 LAN ports (RJ45)
Connect to computers, switches, or other network devices.
○
11 LAN indicators
On: The port is connected to a device.
Blinking: Data is being transmitted through the port.
Off: No device is connected to the port.
○
12 WLAN button
Press and hold for more than 2 seconds to enable or disable the WLAN function.
○
13 Reset button
Press and hold for more than 2 seconds to restore the CPE to its factory settings.
Note:
Restoring the default settings of the CPE will override all the previous settings.
○
14 WPS button
After the WPS function is enabled, press and hold this button for more than 0.5 seconds to
initiate WPS interconnection.
○
15 External antenna ports (SMA-J)
Connect to external antennas.
Note:
Before you connect an external antenna to the CPE, remove the CPE's rear cover.
Getting Started
Installing the SIM Card
Install the SIM card according to the illustration.
Note:
When removing the SIM card, gently press the SIM card in, then release. The card
will automatically pop out.
Do not remove the SIM card when it is in use. Doing so will affect the performance
of your CPE, and data stored on the SIM card may be lost.
Connecting to a Power Adapter
Install the power adapter according to the illustration.
Note:
Only use power adapters compatible with the CPE and provided by a designated
manufacturer. Use of an incompatible power adapter or one from an unknown
manufacturer may cause the CPE to malfunction, fail, or could even cause a fire.
Such use voids all warranties, whether expressed or implied, on the product.
The CPE's power adapter model is HW-120100XYW, HW-120200XYW,
HKA01212010-XY or HKA02412020-XY. X and Y represent letters or numbers that
vary by region. For details about the specific adapter model, contact an authorized
dealer.
Installing the USB Printer Driver
The CPE allows your computer to connect to your printer. Connect both your computer
and printer to the CPE, and then install the printer driver on your computer. When the
installation is finished, you will be able to access the printer from your computer. The
following procedure uses Windows 7 as an example to describe how to install the printer
driver:
1. Log in to the CPE's web management page and add a USB sharing account.
Note:
For details about how to add such an account, refer to the online help.
2. Click Start, enter \\192.168.1.1 (This is the default CPE IP address. If the IP address has
been changed, use the new one.) in the search box, and press Enter.
The login dialog box of the USB device sharing folder is displayed.
3. Enter the USB sharing account information and log in to the folder.
The folder is displayed.
4. Double-click the printer icon and follow the onscreen instructions to finish the
installation.
Logging In to the Web Management Page
The web-based configuration utility can be used for initial CPE installation, parameter
configuration, and function management through the browser.
The Windows 7 operating system and Internet Explorer 8.0 are used as an example. Ensure
that the CPE is connected to the computer. Follow these steps to log in to the web
management page:
1. Connect CPE cables.
2. Configure the computer's IP address so that the IP addresses of the computer and the
CPE are in the same network segment.
Note:
The CPE's default IP address is 192.168.1.1, the subnet mask is 255.255.255.0.
It is recommended that you use the automatically obtained IP addresses for the
computer and domain name system (DNS) server. If you manually configure the
computer IP address, you must set the DNS server IP address to the CPE's IP
address. Otherwise, you will fail to log in to the web management page.
3. Open the browser, and enter http://192.168.1.1 in the address box.
4. Enter the user name and password to log in to the web management page.
Note:
The default user name and password are printed on the CPE label.
LTE is a trademark of ETSI. Version: V100R001_01 Part Number: 31010PTM
