ETM ETM450C Manuel utilisateur

ETM350C & ETM450C

User Manual

Industrial Ethernet Router

Features ETM350C // ETM450C:

◩ HSDPA/UMTS 850/900/2100MHz // 850/900/1900/2100MHz

◩GSM/GPRS 900/1800MHz // 850/900/1800/1900MHz

◩HSUPA 14.4Mbps DL, 5.76Mbps UL (ETM450C only)

◩HSDPA 3.6Mbps // 7.2Mbps DL, 384Kbps // 2.0Mbps UL

◩UMTS 384Kbps UL, 384Kbps DL

◩1 x Ethernet Port 10/100Mbps

◩RJ12 Port for power connection

◩SMA Antenna Connector

◩Supports Dual SIM with automatic failover

ETM350C ETM450C User ManualV008.docx

Page 2 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Contents

Access to Additional Documentation/Software....................................................................................... 3

Alternative Access to Docbanq.......................................................................................................... 3

Introduction ........................................................................................................................................ 4

Nomenclature.................................................................................................................................. 4

Overview........................................................................................................................................ 4

Applications.................................................................................................................................... 4

Specifications...................................................................................................................................... 5

Power Supply...................................................................................................................................... 5

SIM Card............................................................................................................................................ 5

SIM Pin......................................................................................................................................................5

Indicator Lights................................................................................................................................... 6

LAN............................................................................................................................................... 6

Status LEDs .................................................................................................................................... 6

Installation.......................................................................................................................................... 7

Checking Correct Operation ................................................................................................................. 7

Understanding basic operation.............................................................................................................. 7

Modem Router Mode ....................................................................................................................... 7

Accessing the Internet Using the ETM350C/450C.................................................................................. 8

Setting Host PC’s Network Environment ........................................................................................... 8

Web Based Management Interface........................................................................................................ 9

Setting Up a PC to Use the Web Based Management Interface............................................................. 9

Saving Configurations Changes......................................................................................................... 9

Connections Settings...................................................................................................................... 10

WAN Settings..........................................................................................................................................11

LAN Settings...........................................................................................................................................13

DMZ Configuration.................................................................................................................................14

Port Forwarding.......................................................................................................................................14

IP Filter Settings......................................................................................................................................15

Mac Filter Settings..................................................................................................................................16

Pinging.....................................................................................................................................................16

NTP Settings............................................................................................................................................17

DDNS Settings........................................................................................................................................18

Administrator Settings – Name and Password........................................................................................18

Administrator Settings – Saving Configuration......................................................................................18

Administrator Settings -System Logs......................................................................................................19

Administrator Settings - System..............................................................................................................20

Administrator Settings - Update..............................................................................................................20

Reboot.......................................................................................................................................... 21

SMS Commands for ETM350C/450C Router....................................................................................... 22

Page 3 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Access to Additional Documentation/Software

ETM provides access to additional product documentation and software tools via an internet

service (Docbanq) which can be accessed via the following link;

http://www.etmpacific.com.au/content/ETM_Documents.htm

Allow the ActiveX to install

This should allow access to Docbanq, then use the following logon for access to ETM350C

Documentation and software

Account: etm

Password: etMterm1 (case sensitive)

Users of IE8 (Internet Explorer 8) you may have issues connecting, if the following screen

appears…

… then click on the symbol

Alternative Access to Docbanq

If your browser does not support the above features, or fails to function correctly, the Bullant

Browser can be downloaded to your PC to provide access to our document system. To access

Docbanq in this method proceed as follows;

Go to

http://www.docbanq.com/component/option,com_fireboard/Itemid,109/func,view/id,28/catid,3/

And find the section on the page shown below...

Select "here" to download the remote for DocBanq.

After downloading the remote the correct address is;

srap://app5.docbanq.com/

Account: etm

Password: etMterm1

Page 4 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Introduction

Nomenclature

The ETM350C incorporates the Cinterion EU3-P engine and is intended for use in Asia,

Australasia, and Europe (network and regulatory approvals permitting).

The ETM450C incorporates the Cinterion PH8-P engine and is intended for use in Asia,

Australasia, and Europe (network and regulatory approvals permitting).

Overview.

The ETM350C/450C is an industrial 3G Ethernet Router utilising the Cinterion EU3-P module to

provide reliable always on wireless connection for M2M communications requirements.

Terminal Nomenclature/History

Model Comment Module Installed

ETM350C First Release EU3-P

ETM450C First Release PH8-P

Applications

Typical applications include:

◩ Communications link to concentrators/receivers for Metering

◩ Communications link to Programmable Logic Controllers (PLCs)

◩ Communications link for Security Systems

◩ Telemetry applications

◩ Backup communications

Page 5 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Specifications

Feature ETM350C ETM450C

3G UMTS/HSDPA Frequency Bands 850/900/2100 MHz 850/900/1900/2100 MHz

2G GSM/GPRS Frequency Bands 900/1800 MHz 850/900/1800/1900 MHz

SIM Voltage 1.8V & 3V 1.8V & 3V

Supply Voltage 5 to 30VDC 5 to 30VDC

Power Consumption 600mA @ 12VDC 600mA @ 12VDC

Weight 260g 260g

Operating Temperature Range -20°C to +60°C -20°C to +60°C

Power Supply

The ETM350C/450C power connection is a 6 pin RJ12 connector, pin allocations are shown below.

Pin Function Looking at Router RJ12 Socket

1 Power Supply (+5 to +30VDC)

2 Not Used

3 Not Used

4 Not Used

5 Not Used

6 GND

SIM Card

The SIM card slots are located on the underside of the ETM350C/450C Router. The unit supports

both 3V and 1.8V SIMs. Any SIM card used needs to be correctly provisioned for the services and

network upon which it is intended to be used.

SIM Pin

If the SIM used has a PIN either;

•The unit can be configured to enter the SIM pin via the Web Based Management Interface.

•The SIM PIN should be deactivated, insert the SIM in a mobile phone and deactivate the

SIM PIN then transfer the SIM into the router.

Caution

Always disconnect power supply before

inserting or removing SIM Card.

123456

RJ12 Power

Connecto

Ethernet

Connecto

SMA Antenna Connector,

stub antenna supplied

with unit

SIM Access via cover with screw

on underside of unit

Default SIM position is SIM 1

Page 6 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Indicator Lights

LAN

The ETM350C/450C can connect to a Host PC, HUB, Router etc using the embedded 10/100 LAN

port. The RJ-45 connector (LAN port) has two Link-LEDs. The table below shows the each status

of LAN connection.

LED State Description

Green ON Indicates 10Mbps LAN connected.

BLINK Indicates data activity on 10Mbps LAN.

OFF Indicates 10M LAN disconnected.

Orange ON Indicates 100Mbps LAN connected.

BLINK Indicates data activity on 100Mbps LAN.

OFF Indicates 100M LAN disconnected.

Status LEDs

The ETM350C/450C has 6-State LED for indicating the current status.

LED Display Description

Power ON Indicates that power is on

OFF Indicates that power is off

Modem ON Recognizes the HSPA modem

OFF Does not recognize the HSPA modem.

Net BLINK When there is data on the wireless mobile network

OFF When there is no data on the wireless mobile network

IP ON Mobile IP has been acquired from ISP

OFF Mobile IP has not been acquired from ISP

SIM ON The U-SIM card is ready

OFF The U-SIM card is not ready

RSSI

FLASHING 1 quick flash with 4 seconds off for low signal level

FLASHING 2 quick flash with 4 seconds off for medium level

FLASHING 3 quick flash with 4 seconds off for high level

FLASHING 4 quick flashes for 'excellent' signal

OFF Poor or no signal

Page 7 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Installation

The ETM350C/450C is a wireless mobile internet access device for connecting a PC or other LAN

device to a cellular wireless service.

Please follow the steps below when you install this device.

•Insert U-SIM card. There are 2 positions for SIM1 and SIM2. Only 1 SIM is required, the

second SIM is optional.

•Default position is SIM1.

•Connect an appropriate antenna.

•Connect the LAN cable between PC or LAN Device and the LAN port of the

ETM350C/450C.

•Connect the power adapter.

•Turn on the power switch (if fitted).

Checking Correct Operation

The ETM350C/450C connects by PPP (NAT Router) and the “Always on-line Mode” is the default

state.When you get this device for the first time, please check whether the devices settings are

appropriate for your application.

The following steps can be used to check the device is operating correctly.

1. Install ETM350C as above

Ensure the LAN cable is connected between the Device and the ETM350C/450C.

2. When power is applied, the Power LED should turn ON.

3. The Modem LED should turn ON within 20 seconds

4. The SIM LED should turn ON within 60 seconds

If the LED does not turn ON in 60 seconds, then check the SIM card and ensure it is inserted

correctly

5. The NET LED should blink asynchronously whenever data is being transferred or received

6. The RSSI LED blinks when a signal is present

If RSSI LED is off, check the antenna connection and/or location and suitability

7. The IP LED turns ON when the unit has logged on the network and has acquired an IP

address

Understanding basic operation

There are some basic operations of ETM350C/450C.

Modem Router Mode

In Modem router mode, and when the ETM350C/450C has an IP address, the ETM350C/450C

shares the allocated IP with any connected Host devices via NAT. In this mode the

ETM350C/450C acquires its IP from the mobile network and the device connected to the

ETM350C/450C has a private IP allocated via DHCP from the ETM350C/450C.

There are two options for operation in Modem Router Mode, Always On-line and Demand On-line

under Manual mode. For setting these options, refer to the [WAN] settings section.

Page 8 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Accessing the Internet Using the ETM350C/450C

By default the ETM350C/450C should be set to Modem Router Mode - Always On-line Mode.

Setting Host PC’s Network Environment

Assuming Windows XP, click “My Network Places” and then click the right mouse button and select

“properties”.

Select “Local Area Connection” then click the right mouse button and select “Properties”

Double click the “Internet Protocol [TCP/IP]” item.

Page 9 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Check the “Obtain an IP address automatically” then click the [OK] button.

Host PC’s setting is finished. Connect a LAN cable and a power cable on ETM350C/450C. Wait

until the “IP” LED is on at which time you will be able to access the Internet.

Web Based Management Interface

Setting Up a PC to Use the Web Based Management Interface

You can configure the ETM350C/450C via the Web Based Management Interface. The steps

required to set up the interface are;

1. Set Network environment as indicated in the previous section.

2. Connect the LAN and power cable to the ETM350C/450C.

3. Launch the web browser on your PC (such as Internet Explorer) then enter the following

address, https://192.168.0.1/home.asp (Set by default). This router is designed for secure

environments.

The pop-up window of the login page appears.

The default access settings are;

User name: admin

Password: admin

You can change these settings via the [System config] page -> [SYSTEM] menu.

When the correct information is entered the Web Management Interface will open.

Saving Configurations Changes

After making configuration changes you must click [Apply Changes] and reboot the

ETM350C/450C for the changes to take effect.

Page 10 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

ETM350C ETM450C User ManualV008.docx

Connections Settings

After successfully logging in to the unit, you will see the Home page as below.

Up Time: The time period that the router has been on.

IMEI: ID Number of router.

Firmware version: Router’s firmware version.

Area Information: Cell station router is connecting to.

PIN Status: SIM PIN status.

Signal level: Signal strength.

As an example -65dbM is better than -80dbm.

WAN: Indicates whether the router is connected to a network or not.

If connected, it will show the IP address that the Network has assigned to

this router, and the volume of data that has been upload/download during

the current session.

LAN: IP address of this router within local network.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité