ETM ETM770-IoT Manuel utilisateur

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

Features:

•

Cat NB & Cat M1 Connectivity

•

2G (GSM/EGPRS) Connectivity

•

Select the most suitable antenna

•

OLED display

•

Send measured data to EWO server

•

Rechargeable battery

•

Sleep Mode for super low power

consumption

•

Includes antenna, hard case and

charger

USER

GUIDE

ETM770-IoT

CELLULAR NETWORK MONITORING TOOL

2G/CAT-M1/CAT-NB

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au 
 
2
 
 
 
 
 
 
 
TABLE OF CONTENTS 
Connecting the sim card...................................................................................................................................3
Get started scanning a signal with ETM770.................................................................................................4
2G Mode ............................................................................................................................................................5
CAT-M1 Mode...................................................................................................................................................6
CAT-NB Mode...................................................................................................................................................6
Additional Settings.............................................................................................................................................8
Select Radio Band............................................................................................................................................8
Select which operator to scan amongst available operators......................................................................8
View Current Network Data.......................................................................................................................... 10 
View last scan ................................................................................................................................................ 14 
Communication Test ..................................................................................................................................... 15 
Send Data to Server...................................................................................................................................... 16 
Device Data.................................................................................................................................................... 17 
Select APN ..................................................................................................................................................... 18 
Select User/Password for ISP ..................................................................................................................... 18 
Server Address .............................................................................................................................................. 19 
Restart Device................................................................................................................................................ 20 
 

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

CONNECTING THE SIM CARD

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

GET STARTED SCANNING A

SIGNAL WITH ETM770

1. Insert SIM card as shown in picture above.

2. Insert the charger into the mini USB connector. The battery is charged with 5V.

3. To turn the device on, press the power button for a minimum of 3 seconds. When

the device is turned on and the charger is successfully connected, the screen

shall look as follows:

The battery is fully charged. The network connection is 10/10 bars. We are connected to a 2G network with the

frequency 900 MHz R means that the device is logged into the home network.

4. Put on chosen antenna.

5. The device will automatically scan the network signal once turning it on. If not,

find your way to the main menu by pressing the up- button several times. Once

pressing "Signal Scanning" you will be redirected to the second menu. Press

"Scan Signal".

6. Validate your result. The pictures below show a typical scan for a 2G, CatM1 and

CAT-NB connection.

7. By pressing the up button, you will jump to next menu. If you press the up button

multiple times you will finial enter the main menu.

8. By pressing the down button multiple times, you will rotate back to the first row in

the present menu.

9. By pressing the power button for more than 5 seconds, the device will go into

sleep mode.

10.By pressing both the up and the down key for 5 second, the device will restart.

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

2G Mode

Scan Menu 2G mode

I. The device is connected to a 2G band. The channel is 82 and the frequency is

900 MHz

II. Empty space

III. Received Signal Strength Indicator (The signal strength including noise and

interference) measured in dBm. The corresponding value is in the parenthesis. Also

shows Signal Quality (Weak, Low, Medium, High or Strong)

IV. Signal Strength Bar. Measured in dBm.

V. Signal Quality Min and Max values

VI. Empty space

VII. Empty space

VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and RSSI.

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

CAT-M1 Mode

Scan Menu CAT-M1 mode

I. The device is connected to a CatM1 band. The channel is 20 and the frequency is

800 MHz.

II. Reference Signal Received Power (the signal strength without noise and interference)

measured in dBm. The signal is visualized in the signal bar below the data. Also

shows Signal Quality (Weak, Low, Medium, High or Strong)

III. Signal Quality Bar.

IV. Reference Signal Received Quality (how well the signal is coded) measured in dB.

The signal is visualized in the signal bar below the data.Signal Quality Bar.

V. Signal Quality Bar

VI. Signal to Interference plus Noise Ratio (SINR) used to give theoretical upper bounds

on channel capacity (or rate of information transfer)

VII. Signal Quality Bar

VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and RSSI.

CAT-NB Mode

Scan Menu CAT-NB mode

I. The device is connected to a NB band. The band is 20 and the frequency is 800 MHz.

II. Reference Signal Received Power (the signal strength without noise and interference)

measured in dBm. The signal is visualized in the signal bar below the data. Also

shows Signal Quality (Weak, Low, Medium, High or Strong)

III. Signal Quality Bar.

IV. Reference Signal Received Quality (how well the signal is coded) measured in dB.

The signal is visualized in the signal bar below the data.

V. Signal Quality Bar.

VI. Signal to Interference plus Noise Ratio (SINR) used to give theoretical upper bounds

on channel capacity (or rate of information transfer)

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

VII. Signal Quality Bar

VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and RSSI.

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

ADDITIONAL SETTINGS

With ETM770 it is possible to make several additional settings.

Select Radio Band

1. 2. 3.

Main Menu Signal Scan Menu Select Radio Band Menu

1. Starting at the main menu, press "Signal Scanning"

2. Press "Select Radio Band"

3. Select the radio band you want to scan and press OK. By pressing the down

button, more alternatives are visible.

4. Note! When searching for CAT-NB Bands, do not scan all bands at once. This

may cause long scanning time and risk of timeout. If located in Sweden,

band20 is activated for use.

Tip! Check which bands are deployed locally in CAT-M1 and especially CAT-

NB then proceed to only select those bands in order to make scanning faster.

Once the radio band is selected you will automatically be directed back to the Signal

scan menu

Select which operator to scan amongst available operators

1. 2. 3.

Main Menu Signal Scan Menu

1. Starting at the main menu, press "Signal Scanning"

2. Press "Select Net Operators"

Net Operator Menu

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

3. A list of operators is shown. To see which operators are available please see

the numbers on the right of the display. First letter means Operator status and

the second letter means Radio Access Technology (RAT). Operator Status:

0: Unknown, 1: Operator available, 2: Current operator, 3: Operator forbidden

For Support Contact +61 2 9956 7377, sales@etmpacific.com.au

View Current Network Data

1. 2. 3.

Main Menu Signal Scan Menu Current Network Data

1. Starting at the main menu, press "Signal Scanning"

2. At the Signal Scan menu, select "Current Network Data"

3. The first view will look similar to the following:

I. The channel is 2850 and the frequency is 2600 MHz.

II. E-UTRA frequency band: Download bandwidth: Upload bandwidth

III. Mobile Country Code (first part of the PLMN code): Mobile Network Code

(second part of the PLMN code)

IV. FDD or TDD: Physical Cell ID

V. Reference Signal Received Power (RSRP) is -91 dBm.

VI. Reference Signal Received Quality (RSRQ) is -7 dB

VII. Tracking Area Code: Global Cell ID

VIII. The channel is 2850: Public Land Mobile Network (PLMN) is 240007

Autres manuels pour ETM770-IoT

Table des matières

Autres manuels ETM Instrument de mesure

ETM

ETM DeltaBlue Manuel utilisateur

ETM

ETM ETM770 Manuel utilisateur

ETM

ETM ETM770 Manuel utilisateur

ETM

ETM ETM770-4 Manuel utilisateur

ETM

ETM 770 Manuel utilisateur

ETM

ETM ETM770-9 Manuel utilisateur

ETM

ETM ETM770 Manuel utilisateur

ETM

ETM 770-10 Manuel utilisateur

ETM

ETM ETM770-PRO Manuel utilisateur

ETM

ETM Sigicom 770-PRO Manuel utilisateur

ETM

ETM Sigicom 770-PRO Manuel utilisateur

ETM

ETM ETM770-IoT Manuel utilisateur

ETM

ETM ETM770-7 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur