Eternal Lighting CUBE3 Manuel utilisateur

CUBE3™RGB TRI LED

User Manual

(Battery Powered DMX LED Fixture)

Please read over this manual before operating the light.

FIRST CHARGE YOUR FIXTURE FOR 6 HOURS.

Introduction

Unpacking: Thank you for purchasing the CUBE3™ RGB TRI LED. Every CUBE3™ RGB

TRI LED has been thoroughly tested and has been shipped in perfect operating condition.

Carefully check the shipping carton for damage that may have occurred during shipping. If

the carton appears to be damaged, carefully inspect your fixture for any damage and be

sure all accessories necessary to operate the unit has arrived intact. In the case damage

has been found or parts are missing, please contact the manufacturer or your dealer for

further instructions. Do not return this unit to your dealer without first contacting.

Introduction: The CUBE3™ RGB TRI LED is a DMX intelligent LED par light. This par

light is lightweight and compact which makes it a great piece for mobile DJ‟s and clubs.

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to

rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself; doing so will void your manufactures warranty. In the unlikely event your unit may

require service please contact the manufacturer or your dealer.

PLEASE recycle the shipping carton whenever possible.

General Instructions

To optimize the performance of this product, please read these operating instructions

carefully to familiarize you with the basic operations of this unit. These instructions contain

important safety information regarding the use and maintenance of this unit. Please keep

this manual with the unit, for future reference.

Features

Multi-colors

Control Channels:3CH & 7CH

Color Strobe

Master/Slave synchronization

DMX-512 protocol

Electronic Dimming 0-100%

Operating Modes: Sound activation, Auto and DMX control mode

Led operation menu with function buttons

Daisy Chain Units Together in DMX Mode

1-20 flashes/sec strobe effect

Safety Precautions

●To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

●Do not spill water or other liquids into or on to your unit.

●Be sure that the local power outlet match that of the required voltage for your unit.

●Do not attempt to operate this unit if the power cord has been frayed or broken. Do not

attempt to remove or break off the ground prong from the electrical cord. This prong is used

to reduce the risk of electrical shock and fire in case of an internal short.

●Disconnect from main power before making any type of connection.

●Do not remove the cover under any conditions. There are no user serviceable parts

inside.

●Never operate this unit when it‟s cover is removed.

●Never plug this unit in to a dimmer pack.

●Always be sure to mount this unit in an area that will allow proper ventilation. Allow

about 6” (15cm) between this device and a wall.

●Do not attempt to operate this unit, if it becomes damaged.

●This unit is intended for indoor use only; use of this product outdoors voids all

warranties.

●During long periods of non-use, disconnect the unit‟s main power.

●Always mount this unit in safe and stable matter.

●Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to the point they

exit from the unit.

●Cleaning -The fixture should be cleaned only as recommended by the manufacturer.

See “Cleaning” for details.

●Heat -The appliance should be situated away from heat sources such as radiators, heat

registers, stoves, or other appliances (including amplifiers) that produce heat.

●The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in

performance

●Fuse standard is2A/250V

●Grounded using yellow/green line

●The ambient temperature must always be under +35° C

Set Up

Power Supply: Before plugging your unit in, be sure the source voltage in your area

matches the required voltage for your CUBE3™ RGB TRI LED. The CUBE3™ RGB TRI

LED is workable in 100-220V/50~60Hz. Because line voltage may vary from venue to venue,

you should be sure your unit voltage matches the wall outlet voltage before attempting to

operate you fixture.

DMX Linking: To ensure proper DMX data transmission, when using several DMX fixtures

try to use the shortest cable path possible. The order in which fixtures are connected in a

DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX

address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or

anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller

knows to send DATA assigned to address 1 to that unit, no matter where it is located in the

DMX chain.

Operating Instructions

Operating Modes: You can use the CUBE3™ RGB TRI LED in 4 ways:

●Sound activation –The unit will activated by the sound signal.

●Static display –The unit will display the pattern in static way.

●Auto Mode - The unit will automatically chase through the different patterns.

●DMX control mode - This function will allow you to control each individual fixtures traits

with a standard DMX 512 controller.

DMX Mode: Operating through a DMX controller give the user the freedom to create their

own programs tailored to their own individual needs. This function also allows you to use

your fixtures as pattern changing lights.

1. This function will allow you to control each individual fixture‟s traits with a standard DMX

512 controller.

2. The Mini PAR uses 7 DMX channels to operate. Please see “DMX Values and Functions”

for the DMX traits.

3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any

standard DMX controller. Set your desired DMX address following the set up

specifications that come with your DMX controller.

4. The unit can automatically recognize the DMX signal once the DMX connection is done.

DMX Values and Functions

3CH Mode

7CH Mode

Value

Description

CH1

0-255

RED dimmer (0-255)

CH2

0-255

GREEN dimmer (0-255)

CH3

0-255

BLUE dimmer (0-255)

CH4

0-255

R, G, B dimmer (0-255)

CH5

0-255

Auto Slow to Fast (0-255)

CH6

0-255

R, G, B STROBE from slow to fast (0-255)

CH7

0-255

SOUND (Off 0-15 ON 16-255)

Touch Buttons

There are four touch buttons under the LED display: Menu, Down, Up, Enter. Normally, the

LED will display the current DMX address code of the fixture. At this time, presses Menu to

choose the function you want to set up. Press and hold Up or Down to fast scrolling within

the menu options. When an option is flashing the LED display, press Enter to confirm and

Menu to exit.

Value

Description

CH1

0-255

RED dimmer (0-255)

CH2

0-255

GREEN dimmer (0-255)

CH3

0-255

BLUE dimmer (0-255)

LED Operation Menu:

After initialization, the unit is ready for setting and working. Please see the following table for

setting information.

Display

Function

ADDR

DMX Address（0-512）

CHMD

3CH/7CH

SLND

NAST

Master

SLAL

Slave

SHND

SOND

Sound control

COLO

Color choose 1-7

Auto operation

FADE

Running Speed (SP1-SP8)

NANU

Red (0-255)

Green (0-255)

Blue（0-255）

TEST

Quality Control

For Battery Function and Charge

The unit has the function of battery powered. The button for battery and charge is set on the

rear panel. It is showed as the following picture, and the function is described as below.

(1) Alpha-numeric display (2) Touch switches

(3) Microphone (4) DMX-In socket

(5) DMX-Out socket (6) Power switch

(7) Battery switch (8) GND

(9) Power socket and fuse holder (10) Fixation screw

(11) Mounting bracket

There are two buttons on the rear panel of the lighting. One is for power, and the other is

for battery.

●When use the fixture with DMX, not battery, please switch the button for power to “on”,

and switch the button for battery to “bat off”.

●When use the fixture with battery instead of DMX, please switch the button for power to

“off”, and also switch the button for battery to “bat on”.

●When charge the light, please switch the button for battery to “charge”. At the same

time, if the switch for power is “on”, the light will be at work during the process of charge,

but will consume some power from the charge; if the switch for power is “off”, the light

will be blackout and not be at work.

Tip for the battery and charge:

●The battery can last for 6 hours when all LEDs on after full charge , and can last for

more than 10 hours on auto running mode. Up to 20 Hours for one color. Results vary

based on LED intensity on scale of 0-255.

●It is suggested to charge the battery for at least 8 hours, which will extend the life span

of the battery.

●At the bottom of the fixture, there is a little hole which is the indicating light for the

charge. When charge the light, the indicating light will be in red, and when charged full,

it will be in green.

For wireless receiver

Wireless Module of DMX512

MODE：PCB-WI-DMX

Brief：

DMX512 wireless receiver/transmitter transmits standard DMX512 protocol data

(generated by console )by wireless way, which solves lighting control issues of wireless

transmitting completely between console and lighting, lighting and lighting and so on, It get

rid of connecting cable limited completely

And also can ensure without any time delay when signal data is transmitting, signal data is

real time and reliably.

This product adopt 2.4G ISM frequency section( global opening section) without

permission limited

High effective GFSK modulate, communication design ; 126 channels jumping frequency

automatically，high anti-jamming ability.

Application: Upgrade DMX512 stage lighting

PCB Hole：

(1) Antenna (2)Power switch for wireless receiver

(3) Wireless indicator (4)ID code selector

Product feature:

1. Product name：2.4G wireless DMX512 R/T molding board

2. Small size，Easy to suit for interior of accessed lighting

3. Single key to operate，tricolor LED displaying

4. Transmitting standard DMX512 protocol data of console，also can transmitting

lighting and lighting DMX512 protocol data.

5. 126 channels jumping frequency automatically，high anti-jamming ability. to

ensure works reliability

6. 7 groups ID code settable，User can use 7 groups individual wireless net without

any interfere each other in the same place..

7. Input voltage：5VDC

8. Work frequency section：2.4G ISM,126 channels frequency section

9. Max transmitting power rate：20dBm

10. Receiver sensitive：-94dBm

11. Signal port：RS485 or CPU series port AURT

Compatible series product as follows:

Wireless transmitter

Operating manual：

1. ID code and LED color corresponding relationship：

1：RED

2：GREEN

3：RED+GREED

4：BLUE

5：RED+BLUE

6：GREEN+BLUE

7：RED+GREED+BLUE

2. Press button on transmitter to select group to match corresponding color on the

receiving fixture.

LED constant lit up：no DMX or wireless signal.

Red LED flash：transmitting.

Green LED flash：receiving

3. RF frequency- - - - - - - - - - - - 2. 400-2. 525 Ghz，total 126 channels，it‟s searching

automatically,

Establishing Communication：

1. Power on DMX512 wireless received board and transmitted board.

2. Press button to set same color of transmitted board and received board., please

Ce manuel convient aux modèles suivants

Autres manuels Eternal Lighting Luminaire

Eternal Lighting

Eternal Lighting Mini60 Spot Manuel utilisateur

Eternal Lighting

Eternal Lighting ElitePar QUAD Manuel utilisateur

Eternal Lighting

Eternal Lighting CUBE5 Manuel utilisateur

Eternal Lighting

Eternal Lighting Surge 8 Manuel utilisateur

Eternal Lighting

Eternal Lighting CUBE4 Manuel utilisateur

Eternal Lighting

Eternal Lighting Cube RGBA Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur