ETC Echo Manuel utilisateur

ETC Installation Guide

Echo Preset Station

Corporate He adqua rte rs nMiddleton, WI, USA |+1 608 831 4116

Globa l Office s nLondon, UK |Rome, IT |Holzkirchen, DE |Paris, FR |Hong Kong

We b etcconnect.com |Support support.etcconnect.com

Trademark and patent info: etcconnect.com/ip |Product information and specifications

subject to change. ETCintends this document to be provided in its entirety.

7140M2110 Rev C Released 2021-12

Overview

Echo Preset Stations activate built-in

presets in compatible power control

products.

Station faceplates and buttons are

available in cream, ivory, gray, black,

and signal white. Preset stations are

provided with station electronics,

buttons, faceplate, a termination kit,

and installation hardware.

This document guides you through the installation and local configuration of

the Preset Station. Advanced (custom) functionality is available using

EchoAccess.

Custom Configuration

For information about the custom configuration options available for the

Preset Station using EchoAccess, reference the EchoAccess Mobile App

integrated help system. User documentation is available for download on our

website etcconnect.com.

Note:

To use the configuration settings applied using EchoAccess,

DIP switch 2 must be enabled. Reference Rotary and DIP Switches on

the next page.

ETC Installation Guide

Echo Preset Station

Prepare for Installation

Preset Stations ship with a termination kit for use with Belden 8471 (or

equivalent wire) and contains a power pigtail, a ground wire pigtail,

receptacle spacers, and all required wire termination connectors for

installation.

The station installs into an industry standard single-gang back box (RACO

690 or equivalent - provided by others) or an optional surface mount back

box (part number 7081A2004-1) sold separately and available from ETC.

Preset Stations connect to the EchoConnect communication bus.

EchoConnect is a bi-directional protocol that uses one pair of wires (data+

and data-) for both data and power. ETC recommends using Belden 8471

Class 2 wire (or approved equal – see the ETC cable cross database

etcconnect.com/Support/Cable-Cross-Database for equal alternatives). The

total combined length of an EchoConnect wire run using Belden 8471 may

not exceed 500m (1,640ft), with a maximum distance of 400m(1,312ft)

between any two devices.

Note:

All control wiring should be installed and terminated by a

qualified installer and should follow standard wiring installation

practices. Leave approximately 25.4cm (10in) of wiring in the back

box for connection and to allow slack for future service needs.

Note:

ETC requires that all stations and devices be grounded for

ESDprotection. Pull an additional 2.5 mm2(14AWG) wire for

grounding when control wires are not installed in grounded metal

conduit.

Environmental

For indoor installation only; 0°C–50°C (32°F–122°F), 5-95% non-condensing

humidity.

Rotary and DIP Switches

Address &

Space

DIP

switches

Rotary and DIP switch settings are accessible on the

back side of the station.

Set Space and Address

The Preset Station participates in an Echo system using

the configured Space and Address, which are

selectable using the two rotary switches on the back

of the station. Each station must be set to a unique

station address for the assigned space.

Echo Preset Station Page 2 of 8 ETC

ETC Installation Guide

Echo Preset Station

By default, these switches are set to Address 1 and Space 1. Station

commands are shared by all devices within an assigned space.

1. Set the Space rotary switch to the desired number (1 through 16) for the

space you want the station to provide lockout.

2. Set the Address rotary switch to the desired address (1 through 16) for

the station identification in the assigned Space.

CAUTION:

Each device on the bus must have its address set to a

unique number (1 through 16) for the space it controls. If two or

more devices use the same address for the same space, the

system will not function properly.

DIP Switch Settings

Functionality is set using DIP switches located just beneath the rotary

switches. The label on the rear of the station identifies these components and

functions.

Switch # Use

1Use Off - When this is set to Off, the “Off” function of the station

is not provided.

2Custom Config - When set to On, custom configuration settings

are applied using EchoAccess. The default position is Off.

3Disable IR Input - When On, the infrared input will be disabled.

Fade Time Disable - Applies a 0 second fade time to all station

actions for non-dim switched mode behavior (when dimming

features are not wanted).

5 Future development

6 Future development

7 Future development

Restore to Defaults at Boot - Setting this DIP switch On, then

cycling power to the station restores the station to factory

defaults. Reset the switch Off after power cycle.

Echo Preset Station Page 3 of 8 ETC

ETC Installation Guide

Echo Preset Station

Installation

Installation should follow all local codes and standard electrical practices. The

back box should be installed level and square for best results. Ensure that the

back box is clean and free of obstructions.

Note:

NEC Class 2 product to be wired in accordance to NEC Article

725 and local jurisdiction requirements.

Note:

When using Category 5 (or equivalent) cable on the

EchoConnect communication bus, please note the following:

•

Cat5 wiring must be terminated using EchoConnect Cat5

Termination Kit and must be installed using a bus topology.

Refer to the installation guide that is provided with the Cat5

Termination Kit (7186A1207) for information to terminate Cat5

wiring.

•

Not all topologies are supported using Cat5; careful planning is

required to ensure the proper termination kits are available and

the wire is pulled appropriately.

Connect Wiring

1. Pull all required wiring (data+, data-) and an additional 2.5mm2

(14AWG) ESDground wire into the back box.

Note:

A ground connection is required between every station and

back box, even when installed with grounded metal conduit.

2. Connect station ESD ground wire pigtail.

a. Strip 11mm (7/16in) of insulation from the ends of the station

ground wire pigtail provided in the termination kit and from the

incoming ground wire.

b. Use one WAGO 221 Series LEVER-NUTS®provided in the termination

kit to connect the station ESD ground pigtail and the incoming

ground. For stations using grounded metal conduit, connect the

ground pigtail to the metal back box ground location.

c. Install the ESD ground wire pigtail FASTON connector to the mating

receptacle on the station electronics.

Echo Preset Station Page 4 of 8 ETC

ETC Installation Guide

Echo Preset Station

3. Terminate EchoConnect wires. EchoConnect is topology free; you may

install the wires in any combination of bus, star, loop, or home-run.

a. Strip 11mm (7/16in) from the ends of each power pigtail wire

provided in the termination kit and from the installed control wires.

b. Use the WAGO connectors provided to connect the power pigtail

wires and the installed Belden 8471 control wires. One WAGO should

be used for the white wire pair (data +) and one for the black wire pair

(data -). Open the terminal levers on the WAGO connector and insert

the installed Belden 8471 wire and the lead from the power pigtail

into the terminals then close the levers.

c. Install the two pin connector from the power pigtail to the mating

receptacle on the station electronics.

Install the Station in the Back box

Note:

For some flush mount applications with certain trim rings it

may be necessary to remove the station’s back cover for insertion into

the back box.

1. Insert the station electronics and

wiring into the back box. The

arrow on the mounting plate must

be directed up.

2. Use receptacle spacers as needed

to provide a flush mounted

station.

a. Fold a spacer in a zig-zag

fashion and press them

together to achieve the

required thickness to fill the

gap between the station, wall surface, and the back box.

b. Cut off and discard the excess.

c. Place the stack between the station electronics and the flush mounted

back box.

3. Secure the station with two screws. If using spacers, insert the screws

through the spacers as well.

Note:

Over tightening of the mounting screws may result in poor

button activation.

4. Install the button caps (included with the faceplate kit) so that the clear

light tunnels protrude through the caps.

Echo Preset Station Page 5 of 8 ETC

ETC Installation Guide

Echo Preset Station

Install the Faceplate

The faceplate is secured to the station with two magnets that are located on

the bottom edge of the faceplate.

1. Align the top of the faceplate

approximately 20 degrees to the

station.

2. Hook the top of the faceplate on the

tabs located on the top of the station

electronics assembly. To ensure the

faceplate is hooked properly on the

top hook, wiggle it slightly side to side

while the bottom is angled 20 degrees

from the wall.

3. Swing the bottom of the faceplate down until the magnets engage.

4. If the faceplate does not fully attach, wiggle the bottom of the plate until

the magnets are seated properly to the station and the faceplate is

secure.

Echo Preset Station Page 6 of 8 ETC

ETC Installation Guide

Echo Preset Station

Settings

Settings for Basic config mode (DIP switch 2 set to Off) can be modified

locally, including changing which presets are assigned to the station,

changing the button LED color, and preset recording at the station.

Assign Presets

Stations default to controlling Presets 1 through 5. Any station can be set to

control any consecutively numbered block of presets. For example: a 5-button

station can control Presets 1 through 5, 3 through 7, 14 through 18, and so

on.

EchoConnect bus power must be connected to the station to assign the

presets.

MODE button

1. Press and hold the station [MODE] button for

three seconds. The LED beneath the [MODE]

button will illuminate.

2. Press the first preset button on the station a

number of times equal to the first preset you

want the station to control.

•

For example: press six times to associate the

station with Presets 6 through 10 (5-button

station) or 6 through 15 (10-button station).

The first preset button will respond by flashing

to indicate the first preset number. The number

of flashes equals the station’s starting preset

number.

•

After 90 seconds of inactivity, the MODE status will timeout and any

changes are cancelled.

a. While in this mode, button presses are cumulative. If you need to

increase the desired number, press the first preset button additional

times.

b. If you have added too many, wait for the 90 second timeout to cancel

the changes and then repeat this procedure.

3. Press and release the [MODE] button to save the setting.

Echo Preset Station Page 7 of 8 ETC

ETC Installation Guide

Echo Preset Station

Change Button LED Color

Stations default to illuminating preset buttons in green. To change the color

of the LEDs at the station, follow this procedure:

1. Press and hold the [MODE] button for five seconds. The LED beneath the

[MODE] button illuminates and all of the preset buttons display in their

current configured color.

2. Press the first preset button to cycle through the available colors until the

desired color is shown.

•

After 90 seconds of inactivity, the MODE status will timeout and any

changes are cancelled.

3. Press and release the [MODE] button to save the setting. The station

preset buttons show their new selected color.

Preset Record

To record a preset to a button on the Preset Station:

1. Set the desired lighting look in the space.

2. Press and hold the preset button for three seconds. The preset is

recorded to the selected button. The button LED flashes four times to

confirm the record action.

Service

If you have any difficulties installing your system or with system startup

please, contact ETC Technical Services at the office nearest you. ETC contact

information is located at the bottom of

page 1

Echo Preset Station Page 8 of 8 ETC

Table des matières

Autres manuels ETC Système de contrôle

ETC

ETC Eos Apex 5 Manuel utilisateur

ETC

ETC Rover Manuel utilisateur

ETC

ETC sensor+ CEM+ Feuille d'instructions

ETC

ETC Response Mk2 One-Port Feuille d'instructions

ETC

ETC EUTRAC Manuel technique

ETC

ETC Obsession II Manuel utilisateur

ETC

ETC QuickTouch+ 4 Manuel utilisateur

ETC

ETC Emphasis Lighting Control System Manuel utilisateur

ETC

ETC Expression Show Control System Manuel utilisateur

ETC

ETC Cem 3 Manuel utilisateur

ETC

ETC Emphasis Lighting Control System Manuel utilisateur

ETC

ETC CEM3 Manuel utilisateur

ETC

ETC Sensor IQ 500kcmil Kit Manuel utilisateur

ETC

ETC Obsession II Manuel utilisateur

ETC

ETC sensor+ CEM+ Manuel utilisateur

ETC

ETC IRIDEON Manuel utilisateur

ETC

ETC Sensor3 CEM3 Manuel utilisateur

ETC

ETC EOS Manuel utilisateur

ETC

ETC Unison Manuel utilisateur

ETC

ETC Gio Manuel utilisateur

ETC

ETC Echo Inspire Station Mode d'emploi

ETC

ETC Insight 2x Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur