ESKUTE Star Manuel utilisateur

Electric Bike

www.eskute.com

User Manual

Model: Star

WELCOME!

Congratulations on the purchase of your new Star and

welcome to the Eskute team!

About

this User Manual

It is impoant for you to understand your new electric bike.

Even if you have ridden an e-bike before, it is impoant for

eve person to read this manual before riding - you’ll know

how to get better peormance, comfo, and enjoyment from

your new e-bike!

Before riding your e-bike, you

will need to charge your

batte fully before using.

Failure to do so may damage

the batte life and

peormance.

CAUTION WARNING

Don’t dismantle and repair pas by

yourself, please go to the local

distributor or the seicing station if

necessa. For any questions or

concerns, please email to

suppo@eskute.com or visit

www.eskute.com.

TABLE OF CONTENTS

Section 1. Geomet

Section 2. Specication

Section 3. Assembling Your Bike

Section 4. Fold & Unfold the Bike

Section 5. Charging the Batte

Section 6. Maintenance Instructions

Section 7. More Tips

Section 8. Warranty

Handlebars

Front Wheel

Seat / Saddle

Pedals

Tires

Brakes

Batte Care

Saddle

Geomet

Handlebar

On/O Switch

Display

Shifter

Brake

Throttle

Batte

Headlight

Front Fork

Front Brake

Frame

Tail Light

Fender

Rear Brake

Fat Tire

Rear Derailleur

Specication

Model

Frame Material

Batte

Range

Charger

Charging Time

Motor

Speed

Display

Sensor

Suspension

Shifter

Rear Derailleur

Front & Rear

Brakes

Suitable Height

Load Capacity

Item Weight

Up to 22 MPH

LCD Display

Speed Sensor

Hydraulic lockout, Coil spring

adjust for preload

Star

6061 Aluminum Alloy

48V, 20Ah with Samsung/LG Cells

50-80 Miles Average (estimate)

54.6V, 3A

4-5 Hour Charging

48V, 500W Sutto (Bafang) Hub Motor

SHIMANO 7 Speed

CST, 20” x 4.0”

Hydraulic Disc Brakes

160-190 cm / 5’2”- 6’2”

125 kg / 276 lbs

74 lbs

1. Stem plate bolt removal 2. Tightening stem plate bolts.

STEP 1. Install the Handlebars

Assembling Your Bike

Note: DO NOT depress the brake levers before

installing the front wheel.

1. Using the Allen wrench, unscrew the 4 bolts and remove

the stem plate.

2. Place your handlebars into the groove and replace the

stem plate over the top. Tighten the bolts about 3/4this

of the way.

3. Make the nal adjustments on your handlebars position,

ensuring that they are centered and at a comfoable angle

before tightening the bolts the rest of the way.

Before assembling, check that all pas are complete and

in good condition. If you have any questions or cannot

nd the information you need in the manual, please

contact at suppo@eskute.com.

NOTE:

1. Take o the plastic protective gaps on each side, throw these

away.

2. Loosen up both bolts untill you are able to slide the wheel into

place, making sure the brake caliper slides onto the rotor and

both of the forks are properly hooked onto the wheel, fasten

and screw the bolts.

STEP 2. Install the Front Wheel

1. Remove the protective gaps

Tip: DO NOT raise the saddle higher than the safety line.

1. Loosen the seat post clamp and inse saddle post.

2. Adjust saddle to the preferred height then tighten clamp.

1. Dropping seat into bike.

2. Tighten the seat post clamp.

STEP 3. Install the Seat

2. Fasten both screws

1. Unfold the bike frame

2. Press the latch lock to

release mechanism.

1. Check the end cap on both pedals in order to identify the left

and right pedal.

2. Grab the wrench, and screw the pedal tightly into the correct

crank. The pedals should thread smoothly and easily if properly

aligned.

1. left vs. Right pedal

2. Attaching pedal to crank

STEP 4. Attach the Pedals

Tip: Imagine that you are sitting on the bike to correctly determine

left vs. right side.

Fold & Unfold the Bike Frame

Fold & Unfold the Handle Stem

3. Proceed when you achieve

the status as pictured.

4. Fasten the latch

as pictured.

1. Loosen quick release.

2. Tilt the stem slowly.

3. Fasten the stem latch upward

to lock it in place.

4. Jiggle the stem to see If it’s

rmly locked in place.

Charging the Batte

Tip: The batte can be charged on/o your bike. Make sure that

your motor system and batte is turned completely o

before beginning any charging procedures.

Table des matières

Autres manuels ESKUTE Scooter

ESKUTE

ESKUTE Polluno Pro Manuel utilisateur

ESKUTE

ESKUTE ES MAX Manuel utilisateur

ESKUTE

ESKUTE ES1 Manuel utilisateur

ESKUTE

ESKUTE Polluno Manuel utilisateur

ESKUTE

ESKUTE Spark Y Manuel utilisateur

ESKUTE

ESKUTE Netuno Pro Manuel utilisateur

ESKUTE

ESKUTE Netuno Manuel utilisateur

ESKUTE

ESKUTE Netuno Manuel utilisateur

ESKUTE

ESKUTE MYT-27.5 Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur