ESIS ADAM-5000 Series Manuel utilisateur

ADAM-5000 Series

I/O Module

User's Manual

2.4 rd Edition

May 2008

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual

Introduction

This manual introduces the detail specifications functions and

application wiring of each ADAM-5000 I/O modules. To organize

an ADAM-5510 Series Controller, you need to select I/O modules

to interface the main unit with field devices or processes that you

have previously determined. Advantech provides 23 types of

ADAM-5000 I/O modules for various applications so far. Following

table is the I/O modules support list we provided for user’s choice.

Module Name Specification Reference

Analog I/O

ADAM-5013 3-ch. RTD input Isolated

ADAM-5017 8-ch. AI Isolated

ADAM-5017P 8-ch. AI with independent Input Isolated

ADAM-5017H 8-ch. High-speed AI Isolated

ADAM-5017UH 8-ch. Ultra High-speed AI Isolated

ADAM-5018 7-ch. Thermocouple input Isolated

ADAM-5018P 7-ch. Thermocouple input with

independent Input Isolated

ADAM-5024 4-ch. AO Isolated

Digital I/O

ADAM-5050 7-ch. D I/O Non-isolated

ADAM-5051 16-ch. DI Non-isolated

ADAM-5051D 16-ch. DI w/LED Non-isolated

ADAM-5051S 16-ch. Isolated DI w/LED Isolated

ADAM-5052 8-ch. DI Isolated

ADAM-5053S 32-ch. Isolated DI Isolated

ADAM-5055S 16-ch. Isolated DI/O w/LED Isolated

ADAM-5056 16-ch. DO Non-isolated

ADAM-5056D 16-ch. DO w/LED Non-isolated

ADAM-5056S 16-ch. Isolated DO w/LED Isolated

ADAM-5056SO 16-ch. Iso. DO w/LED (source) Isolated

ADAM-5057S 32-ch. Isolated DO Isolated

Table 1: I/O Module Support List

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual P.

Module Name Specification Reference

Relay Output

ADAM-5060 6-ch. Relay output Isolated

ADAM-5068 8-ch. Relay output Isolated

ADAM-5069 8-ch. Relay output Isolated

Counter/Frequency

ADAM-5080 4-ch. Counter/Frequency Isolated

ADAM-5081 4-ch/8-ch High Speed

Counter/Frequency Isolated

Serial I/O

ADAM-5090 4-port RS232 Non-isolated

ADAM-5091 4-port RS232 with Share

Interrupt Non-isolated

ADAM-5095 2-port CAN with Isolation

protection Isolated

Storage ADAM-5030 2-slot SD Storage Module

Motion ADAM-5202 2-port AMONet Master Module

Table 2: I/O Module Support List

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual

1. Analog Input Modules

Analog input modules use an A/D converter to convert sensor

voltage, current, thermocouple or RTD signals into digital data. The

digital data is then translated into engineering units. The analog

input modules protect your equipment from ground loops and

power surges by providing opto-isolation of the A/D input and

transformer based isolation up to

3,000 V

ADAM-5013 3-channel RTD input module

The ADAM-5013 is a 16-bit, 3-channel RTD input module that

features programmable input ranges on all channels. This module is

an extremely cost-effective solution for industrial measurement and

monitoring applications. Its opto-isolated inputs provide 3,000 V

of isolation between the analog input and the module, protecting

the module and peripherals from damage due to high input line

voltage.

Note: Owing to the conversion time required by the A/D

converter, the initialization time of each ADAM-5013 module

is 5 seconds. Thus the total initialization time will be about 20

seconds if all 4 I/O slots in an ADAM-5000 main unit

contain ADAM-5013 modules.

ADAM-5013

Figure 1: ADAM-5013 module frontal view

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual P.

Application wiring

Figure 2: RTD inputs

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual

Technical specifications of ADAM-5013

Analog input channels three

Input type Pt or Ni RTD

RTD type and temperature range

Pt -100 to 100°C a=0.00385

Pt 0 to 100°C a=0.00385

Pt 0 to 200°C a=0.00385

Pt 0 to 600°C a=0.00385

Pt -100 to 100°C a=0.00392

Pt 0 to 100°C a=0.00392

Pt 0 to 200°C a=0.00392

Pt 0 to 600°C a=0.00392

Ni -80 to 100°C

Ni 0 to 100°C

Isolation voltage 3000 VDC

Sampling rate 10 samples/sec (total)

Input impedance 2 MΩ

Bandwidth 13.1 Hz @ 50 Hz

15.72 Hz @ 60 Hz

Input connections 2, 3 or 4 wire

Accuracy ± 0.1% or better

Zero drift ± 0.015 °C/°C

Span drift ± 0.01 °C/°C

CMR@50/60 Hz 150 dB

NMR@50/60 Hz 100 dB

Power consumption 1.2 W

Table 2: Technical specifications of ADAM-5013

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual P.

ADAM-5013 RTD Input Resistance Calibration

1. Apply power to the module and let it warm up for about 30 minutes.

2. Make sure that the module is correctly installed and is properly

con- figured for the input range you want to calibrate. You can

use the ADAM utility software to help in this.

3. Connect the correct reference self resistance between the screw

terminals of the ADAM-5013 as shown in the following wiring

diagram. Table 2 below shows the correct values of the span and

zero calibration resistances to be connected. Reference

resistances used can be from a precision resistance decade box or

from discrete resistors with the values 60, 140, 200 and 440 ohms.

Figure 3: Applying calibration resistance

4. First, with the correct zero (offset) calibration resistance connected

as shown above, issue a Zero Calibration command to the module

using the Calibrate option in the ADAM utility software.

5. Second, with the correct span resistance connected as shown

above, issue a Span Calibration command to the module using

the Calibrate option in the ADAM utility software. Note that the

module zero calibration must be completed prior to the span

calibration.

Note: If the above procedure is ineffective, the user must first issue an

RTD Self Calibration command $aaSi2 to the module and then

complete steps 4 and 5 after self calibration is complete.

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual

Calibration resistances (ADAM-5013)

Input Range

Code (Hex)

Input Range Span

Calibration

Resistance

Zero

Calibration

Resistance

20 Pt, -100 to 100°C A = 0.00385 140 Ohms 60 Ohms

21 Pt, 0 to 100°C A = 0.00385 140 Ohms 60 Ohms

22 Pt, 0 to 200°C A = 0.00385 200 Ohms 60 Ohms

23 Pt, 0 to 600°C A = 0.00385 440 Ohms 60 Ohms

24 Pt, -100 to 100°C A = 0.00392 140 Ohms 60 Ohms

25 Pt, 0 to 100°C A = 0.00392 140 Ohms 60 Ohms

26 Pt, 0 to 200°C A = 0.00392 200 Ohms 60 Ohms

27 Pt, 0 to 600°C A = 0.00392 440 Ohms 60 Ohms

28 Ni, -80 to 100° C 200 Ohms 60 Ohms

29 Ni, 0 to 100°C 200 Ohms 60 Ohms

Table 3: Calibration resistances of ADAM-5013

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual P.

ADAM-5017 8-channel analog input module

The ADAM-5017 is a 16-bit, 8-channel analog differential input

module that provides programmable input ranges on all channels.

It accepts mill volt inputs (±150mV, ±500mV), voltage inputs (±1V, ±5V

and ±10V) and current input (±20 mA, requires 120 ohms resistor).

The module provides data to the host computer in engineering units

(mV, V or mA). This module is an extremely cost-effective solution

for industrial measurement and monitoring applications. Its opto-

isolated inputs provide 3,000 V

of isolation between the analog input

and the module, protecting the module and peripherals from damage

due to high input line volt- age. Additionally, the module uses analog

multiplexers with active over- voltage protection. The active

protection circuitry assures that signal fidelity is maintained even

under fault conditions that would destroy other multiplexers. This

module can withstand an input voltage surge of 70 Vp-p with ±15 V

supplies. The jumpers of ADAM-5017 are designed for current input.

ADAM-5017

Figure 4: ADAM-5017 module frontal view

I/O Module Introduction

ADAM-5000 Series I/O Module User’s Manual

Application wiring

Figure 5: Millivolt and volt input



Figure 6: Process current input

Note: To keep measurement accuracy please short the channels that

are not in use.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur