ESAB PSF 315M Manuel utilisateur

Valid for serial no. 217, 6340457 342 101 GB 060822

PSFt315 M

PSFt315 R

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 4...................................................

4 TECHNICAL DATA 5.................................................

5 CONSUMABLES 5...................................................

5.1 Changing wire liner, replacing electrode conductors 5............................

5.2 Interchangeable connectors 6.................................................

5.3 Compressed air cleaning 6...................................................

5.4 Contact tip 7................................................................

5.5 Wire liners 7................................................................

5.6 Gas nozzles 7..............................................................

5.7 Gas protection 7............................................................

6 OPERATION 8.......................................................

7 MAINTENANCE 8....................................................

8 SPARE PARTS AND ACCESSORIES 8.................................

DIMENSION DRAWING 9................................................

ORDERING NUMBER 10.................................................

WEAR PARTS 12........................................................

ACCESSORIES 13.......................................................

-- 3 --

bg14e

1DIRECTIVE

DECLARATION OF CONFORMITY

ESAB Welding Equipment AB, S--695 81 Laxå, Sweden, gives its unreserved guarantee that welding

gun PSF 315 M / 315 R from serial number 217 complies with standard EN 60974--7, in accordance

with the requirements of directive (73/23/EEC) and addendum (93/68/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Henry Selenius

Vice President

ESAB Welding Equipment AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924

Laxå 2002--04--25

2SAFETY

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection and accessories.

-- 4 --

bg14e

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

3 INTRODUCTION

The PSFt315M / 315 R is an self--cooled welding gun. The welding gun is

developed for use in robot applications or mechanised welding.

A range of accessories including welding tips, swan necks and contact nozzles are

also available.

Details of ESAB’s welding torches accessories can be found on page 13.

-- 5 --

bg14e

4 TECHNICAL DATA

Welding gun PSF 315 M / 315 R

Permitted load at 60% intermittence

CO2

MIX 315 A

285 A

Permitted load at 100% intermittence

CO2

MIX 200 A

170 A

Electrode dimensions 0.8 -- 1.2 mm

Rec. gas flow l/min 10 -- 20 l/min

Weight, hose length

1.5 m

2.2 m

2.0 kg

2.6 kg

3.2 kg

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

5 CONSUMABLES

5.1 Changing wire liner, replacing electrode conductors

5.1.1 Install the correct nipple

ESAB Connection EURO Connection

Note! 2 nipples are supplied with each welding liner, 1 for an ESAB connection and 1 for a

EURO connection.

5.1.2 Remove the gas nozzle and tip adator.

5.1.3 Install the wire liner in the welding gun.

-- 6 --

bg14e

5.1.4 Cut the wire liner to the correct length.

When cutting, the welding gun should be extended with the wire liner fully inserted in

the rear connection.

Cut the wire liner so that it protrudes by “X” in accordance with the table below.

Welding gun Length Adapter Measu-

rement

Helix Measu-

rement

PSF 315 M / 315 R 1.5 m 0368 145 001 27 mm 0368 683 001 22 mm

PSF 315 M / 315 R 2.2 m 0368 145 001 28 mm 0368 683 001 23 mm

PSF 315 M / 315 R 3.0 m 0368 145 001 31 mm 0368 683 001 26 mm

Sharp edges are not allowed on the inside of the wire liner guide after cutting.

5.1.5 Reinstall the tip adaptor and gas nozzle.

5.1.6 Install the welding gun on the machine.

a) Turn the connecting piece clockwise when you encounter resistance

b) The welding rod goes in

5.2 Interchangeable connectors

Connectors are manufactured with the same measurements between the mount and

the tip of the contact tip and are therefore directly interchangeable.

For dimensions and guaranteed tolerances, see diagram on page 9.

5.3 Compressed air cleaning

The connector has a connection and ducts for compressed air cleaning of the gas

nozzle.

-- 7 --

bg14e

5.4 Contact tip

Contact tips are selected according to electrode diameter, type of shielding gas and

rating of the welding current being used. See table on page 13.

The contact tips are initially selected with the guidance of the CO2table. If seizing

occurs in the event of high welding data with Argon or mixed gas, select on the basis

of the MIX, AR table.

For HELIX, the table applies regardless of shielding gas type. HELIX contact tips

must be combined with a special tip adaptor, see spare parts list. Note that the item

number for HELIX includes 2 contact tips + 1 locking nut for installation.

5.5 Wire liners

In order to achieve good welding rod feed, the wire liner should be selected in

accordance with the table on page 14. A PTFE--based wire liner produces less

friction and is kinder to the electrode, but normally has a shorter service life than a

steel spiral. It is suitable for all types of electrode, except for the majority of core wire

types thicker than 1.2 mm.

Steel spirals can be used for all except for stainless steel and aluminium electrodes.

For changing electrode guides – see the enclosed instructions.

Note! All welding guns are supplied with steel spirals for welding liner ∅1.0.

5.6 Gas nozzles

If you want a gas nozzle with a smaller opening diameter, this is available as an

accessory for each gun. See the spare parts list. Note that it is also possible to

exchange the connector type.

IMPORTANT! There is a spatter guard in the gas nozzle. This must be in place to

prevent welding spatter penetrating the connector.

For good function, the gas nozzle must always be screwed in as far as it will go.

5.7 Gas protection

Several factors combine to provide good gas protection. The most important of these

are:

1. Choice of shielding gas. -- Mixed gas and argon require a greater flow than

carbon dioxide

2. Set flow quantity. -- See technical data (should be measured at the gas nozzle).

3. Set welding current. -- High current requires a greater gas flow.

4. Position of the welding joint. -- A vertical position requires a greater gas flow.

5. Type of welding joint. -- An outer corner joint requires a greater gas flow than a

butt joint. A fillet weld joint requires a correspondingly smaller gas flow.

6. The angle of the welding gun against the workpiece -- below 45°entails a risk of

poor gas protection.

-- 8 --

bg14e

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

The welding gun contains a lead for starting point searching. This is connected to the

ring--shaped adapter plug in the welding gun’s feeder end. The connection lead from

starting point searching (e.g. Smartac) is connected to the corresponding flat--pin

connection in the feeder’s terminal block.

7 MAINTENANCE

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself

attempts any work in the product during the guarantee period in order to rectify any

faults.

Regular servicing reduces unnecessary and expensive operational stoppages.

1. Welding spray in the gas nozzle impairs the gas protection and increases the risk

of flash--over.

--Clean regularly and use a moderate amount of welding paste or welding spray.

2. The spray guard in the gas nozzle should be replaced when its front end has

become thin.

3. Every time the electrode bobbin is replaced, the welding hose should be

disconnected from the feeder and blown clean with compressed air.

4. The end of the electrode may not have any sharp edges when it is inserted into

the welding rod guide. This is particularly important in the case of PTFE--based

welding rod guides.

8 SPARE PARTS AND ACCESSORIES

PSF 315 M / 315 R is designed and tested in accordance with the international and Eu-

ropean standards IEC/EN 60974--7 and EN 60974--7. It is the obligation of the service

unit which has carried out the service or repair work to make sure that the product still

conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page of

this publication. When ordering, please state product type, serial number, designa-

tion and spare part number in accordance with the spare parts list.

This facilitates shipment and ensures correct delivery.

Dimension drawing

-- 9 --

bg14dim

(mm)

PSFt315M, 25˚3.5 20 22 94 196.3 63.4

PSFt315M, 25˚extended 100 3.5 20 22 94 296.3 63.4

PSFt315M, straight 3.5 20 22 94 209.3 0

PSFt315M, straight, extended 100 3.5 20 22 94 309.3 0

ng gun

t31

Edition 060822

Ordering number

-- 1 0 --

bg14or

Ordering numbers for Welding gun PSFt315 M, PSFt315 R

0367 233 894 PSFt315 M / 315 R 1.5 m, 25˚EURO Connection

0367 233 896 PSFt315 M / 315 R 1.5 m, straight EURO Connection

0367 233 898 PSFt315 M / 315 R 3.0 m, 25˚EURO Connection

0367 233 900 PSFt315 M / 315 R 2.2 m, 25˚EURO Connection

0367 233 901 PSFt315 M / 315 R 2.2 m, straight EURO Connection

0367 233 905 PSFt315 M / 315 R 3.0 m, straight EURO Connection

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ESAB Système de soudage

ESAB

ESAB LAF 1001 Manuel utilisateur

ESAB

ESAB Origo Mig 4002c Manuel utilisateur

ESAB

ESAB Fabricator 252i Manuel utilisateur

ESAB

ESAB Cutmaster 100 Manuel utilisateur

ESAB

ESAB PUA 1 Manuel utilisateur

ESAB

ESAB OrigoFeed 30-2 Manuel utilisateur

ESAB

ESAB PT-26 Manuel utilisateur

ESAB

ESAB Origo Mig 4002c Manuel utilisateur

ESAB

ESAB Caddy Mig C160i Manuel utilisateur

ESAB

ESAB Rogue ES 180i Manuel utilisateur

ESAB

ESAB Mig 4004i Manuel utilisateur

ESAB

ESAB A6 TFD1 Manuel utilisateur

ESAB

ESAB Origo Mig 652c Manuel utilisateur

ESAB

ESAB Warrior 500i CC/CV Manuel utilisateur

ESAB

ESAB A2 TF Manuel utilisateur

ESAB

ESAB Aristo Origo Feed 3004 Manuel utilisateur

ESAB

ESAB OCF 2L Manuel utilisateur

ESAB

ESAB Aristo Mig C3000i Manuel utilisateur

ESAB

ESAB POWERCUT-1500 Manuel utilisateur

ESAB

ESAB PLASMAWELD 202 Manuel utilisateur

ESAB

ESAB Origo Mig 3001i Manuel utilisateur

ESAB

ESAB Buddy Mig 500i Manuel utilisateur

ESAB

ESAB Aristo WeldCloud Mig U5000i Manuel utilisateur

ESAB

ESAB MultiMaster 160 Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur