ESAB PowerCut 700 PT-39 Manuel utilisateur
GB
Valid for serial no. 145-xxx-xxxx0463 339 001 GB 20121125
PowerCut™ 700
PT-39
Instruction manual
- 2 -
- 3 -
- 4 -
- 5 -
TOCe
Rights reserved to alter specifications without notice.
APPLICATIONS 24.......................................................
1 SAFETY 6...........................................................
2 INTRODUCTION 8...................................................
2.1 Equipment 8................................................................
3 TECHNICAL DATA 8.................................................
4 INSTALLATION 9....................................................
4.1 Delivery check and location 10.................................................
4.2 Primary power supply 11......................................................
4.3 Input air connection 12........................................................
4.4 Connection for return cable 12.................................................
4.5 Connection of torch 13........................................................
4.5.1 Disconnecting the Torch 14...............................................
4.5.2 Connecting the Torch 14..................................................
5 OPERATION 15.......................................................
5.1 Connections 15..............................................................
5.2 Control devices 16...........................................................
5.2.1 Symbol key 17..........................................................
5.3 Installing consumables for the torch 18..........................................
5.4 Cutting 19...................................................................
6 MAINTENANCE 20....................................................
6.1 Inspection and cleaning 21....................................................
7 TROUBLESHOOTING 21..............................................
7.1 Troubleshooting guide 22......................................................
8 ORDERING SPARE PARTS 23.........................................
DIAGRAM 24............................................................
WEAR PARTS 27........................................................
ORDER NUMBER 28.....................................................
© ESAB AB 2012
- 6 -
bp29e
1 SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be
observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
Sits operation
Slocation of emergency stops
Sits function
Srelevant safety precautions
Swelding and cutting
2. The operator must ensure that:
Sno unauthorised person is stationed within the working area of the equipment when it is
started up.
Sno-one is unprotected when the arc is struck
3. The workplace must:
Sbe suitable for the purpose
Sbe free from drafts
4. Personal safety equipment
SAlways wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
SDo not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
SMake sure the return cable is connected securely.
SWork on high voltage equipment may only be carried out by a qualified electrician.
SAppropriate fire extinquishing equipment must be clearly marked and close at hand.
SLubrication and maintenance must not be carried out on the equipment during operation.
GB
© ESAB AB 2012
- 7 -
bp29e
WARNING
Read and understand the instruction manual before installing or operating.
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
SInstall and earth the unit in accordance with applicable standards.
SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
SInsulate yourself from earth and the workpiece.
SEnsure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
SKeep your head out of the fumes.
SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
SProtect bystanders with suitable screens or curtains.
FIRE HAZARD
SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
SProtect your ears. Use earmuffs or other hearing protection.
SWarn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
WARNING
Do not use the power source for thawing frozen pipes.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
CAUTION
This product is solely intended for plasma cutting.
CAUTION
Read and understand the instruction manual before
installing or operating.
GB
© ESAB AB 2012
- 8 -
bp29e
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary cutting protection and accessories.
2 INTRODUCTION
The PowerCut 700 is a complete system for manual plasma cutting. It delivers
cutting power for severing materials up to 20 mm thickness.
2.1 Equipment
The power source is supplied with:
Spower cable, 3 m
Sinstruction manual
Sreturn cable with clamp
Splasma cutting torch PT-39, 7.5 m, supplied as indicated on page 28
Swear part kit for PT-39.
3 TECHNICAL DATA
PowerCut 700
Mains voltage 400 V $10 %, 3-ph, 50/60 Hz
Setting range 30 – 50 A
Permitted load
30 % duty cycle
60 % duty cycle
100% duty cycle
50 A
37 A
30 A
Power factor at max current 0.75
Efficiency at maximum current 85 %
Open-circuit voltage U0320 V
Operating temperature -10 to 40 °C
Transportation temperature -20 to 55 °C
Sound pressure at no load < 70 db (A)
Nominal flow rate 189 l/min at 4.8 bar
Dimensions, l x w x h 600 x 210 x 380 mm
Weight incl torch and return cable 25.5 kg
Insulation class transformer H
Enclosure class IP 23
Application class
GB
© ESAB AB 2012
- 9 -
bp29e
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40°C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
4 INSTALLATION
The installation must be carried out by a professional.
Correct installation is very important for trouble-free operation and good cutting
results. Carefully read and follow each step in this chapter.
WARNING
ELECTRIC SHOCKS CAN KILL Take precautionary measures against electric
shocks. Ensure that all power supplies are disconnected –switch off the switch
at the wall socket and pull out the equipment's power cable from the socket before
making any electrical connections in the power source.
WARNING
It is very important that the chassis is connected to the approved electric protective
earth, to prevent electric shocks and electrical accidents. Ensure that protective
earth is not connected to any phase conductors by mistake.
WARNING
Poor connections or failure to connect the return cable to the workpiece can result
in fatal electric shock.
WARNING
Air filter devices may not be used –installation or mounting of any form of air
filter device obstructs the cold air flow and causes a risk of overheating.
The warranty is invalidated if any type of air filter is used.
GB
© ESAB AB 2012
- 10 -
bp29e
WARNING
Do NOT start the equipment with the cover removed.
Do NOT connect the power source with the main switch in ON position
or when you are holding it or carrying it.
Do NOT touch any of the torch's parts when the power supply is on.
CAUTION
This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.
CAUTION
Place the power source at least 3 metres from the cutting area as sparks and slag spray
can damage the power source
4.1 Delivery check and location
1. Remove the packaging. Inspect the equipment for damage that was not
immediately apparent upon reception of the delivery. Immediately report any
damage to the delivery company.
2. Check for any loose parts in the packaging. Check that the air ducts in the
cover's rear panel are not blocked by packaging material that can prevent the air
flow through the power source.
The power source has a carrying handle and can be lifted easily.
3. Position the power source so that its cooling air inlets and outlets are not
obstructed. Minimum permitted distance to wall or other obstruction is 1 m.
4. An air source that gives clean and dry air, at least 189 l/m at 4.8 bar, is
required for cutting. The cutting air pressure must not exceed 6 bar, which is the
maximum inlet pressure for the filter regulator that is included in the delivery.
GB
Autres manuels pour PowerCut 700 PT-39
1
Table des matières
Autres manuels ESAB Système de soudage
ESAB
ESAB ESP-101 Manuel utilisateur
ESAB
ESAB LHJ 750 Mode d’emploi
ESAB
ESAB CaddyTig HF Manuel utilisateur
ESAB
ESAB PT-19A Manuel utilisateur
ESAB
ESAB Aristo Origo Feed 4804 Manuel utilisateur
ESAB
ESAB ESABMig 400t Manuel utilisateur
ESAB
ESAB 653 cvcc Manuel de référence
ESAB
ESAB EMP 205ic AC/DC Mise à jour du firmware
ESAB
ESAB PT-31XL Manuel utilisateur
ESAB
ESAB PLASMAWELD 202 Manuel utilisateur
ESAB
ESAB Fabricator ET 410iP Manuel utilisateur
ESAB
ESAB AristoFeed 30- 4 Manuel utilisateur
ESAB
ESAB Precision Plasmarc Manuel du propriétaire
ESAB
ESAB A22 POB Instructions d'utilisation
ESAB
ESAB Origo Tig 3000i Manuel utilisateur
ESAB
ESAB Aristo U6 Manuel utilisateur
ESAB
ESAB ROBUSTFEED EDGE Manuel utilisateur
ESAB
ESAB PCM-1125 Manuel utilisateur
ESAB
ESAB SCT-1500 SERIES Manuel utilisateur
ESAB
ESAB ET 210iP Advanced Manuel utilisateur
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
Elettro
Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur
