ESAB Origo Tig 3000i Manuel utilisateur

Valid for serial no. 612--xxx--xxxx0459 942 001 GB 070809

Tig 3000i AC/DC

Origot

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 5...................................................

3.1 Equipment 5................................................................

3.2 Control panel 5.............................................................

4 TECHNICAL DATA 5.................................................

5 INSTALLATION 6....................................................

5.1 Lifting instruction 6..........................................................

5.2 Location 6..................................................................

5.3 Mains power supply 7........................................................

6 OPERATION 7.......................................................

6.1 Connections and control devices 8............................................

6.2 Key to symbols 8............................................................

6.3 Fan control 8...............................................................

6.4 Overheating protection 8.....................................................

7 MAINTENANCE 9....................................................

7.1 Inspection and cleaning 9....................................................

8 FAULT--TRACING 9..................................................

9 ORDERING SPARE PARTS 10..........................................

DIAGRAM 12............................................................

ORDERING NUMBER 14.................................................

ACCESSORIES 16.......................................................

-- 3 --

bt31d1ea

1DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-

ing power source Tig 3000i AC/DC from serial number 612 are constructed and tested in compliance

with the standard EN 60974--1 /--3 and EN 60974--10 in accordance with the requirements of directive

(2006/95/EC) and (2004/108/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Kent Eimbrodt

Global Director

Equipment and Automation

Laxå 2007--03--14

2SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

-- 4 --

bt31d1ea

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection and accessories.

WARNING!

Read and understand the instruction manual before installing

or operating.

Do not use the power source for thawing frozen pipes.

WARNING!

This product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

-- 5 --

bt31d1ea

3 INTRODUCTION

The Tig 3000i AC/DC is a TIG welding power source, which can also be used for

MMA welding. It can be used with alternating current (AC) or direct current (DC).

ESAB’s accessories for the product can be found on page 16.

3.1 Equipment

The power source is supplied with:

Instruction manual for the welding power source, instruction manual for the control

panel and 5 m return cable.

3.2 Control panel

TA24 AC/DC

See the separate instruction manual for a detailed description of the control panel.

4 TECHNICAL DATA

Tig 3000i AC/DC

Mains voltage 400 V, ±10%, 3∼50/60 Hz

Primary current

Imax TIG

Imax MMA

20 A

25 A

No--load power demand when in the

energy--saving mode, 6.5 min. after welding

30 W

Setting range TIG,AC* / DC

MMA

4--300 A

16--300 A

Permissible load at TIG, AC/DC

35% duty cycle

60% duty cycle

100% duty cycle

300 A / 22 V

240 A / 19.6 V

200 A / 18 V

Permissible load at MMA

30% duty cycle

60% duty cycle

100% duty cycle

300 A / 32 V

230 A / 29.2 V

190 A / 27.6 V

Power factor at maximum current

TIG

MMA

0.72

Efficiency at maximum current

TIG

MMA

67%

77%

Open--circuit voltage

MMA 54--64 V

-- 6 --

bt31d1ea

Tig 3000i AC/DC

Operating temperature -- 1 0 t o + 4 0 ˚C

Constant A--weighted sound pressure <70 dB

Dimensions lxwxh 652 x 412 x 423 mm

Weight 42 kg

Insulation class transformer H

Enclosure class IP 23C

Application class

*) The minimum current during AC welding depends on the alloy used for the aluminium plates and

their surface cleanliness.

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

5 INSTALLATION

The installation must be executed by a professional.

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio

interference. It is the user’s responsibility to take adequate precautions.

5.1 Lifting instruction

5.2 Location

Position the welding power source such that its cooling air inlets and outlets are not

obstructed.

-- 7 --

bt31d1ea

5.3 Mains power supply

Check that the welding power source is connected to the

correct mains power supply voltage, and that it is protected by

the correct fuse size. A protective earth connection must be

made in accordance with regulations.

Rating plate with supply connection data

Recommended fuse sizes and minimum cable area

Tig 3000i AC/DC TIG MMA

Mains voltage 400 V 3μ50 Hz 400 V 3μ50 Hz

Mains cable area mm24G2,5 4G2,5

Phase current IRMS 12 A 14 A

Fuse

anti--surge

type C MCB

16 A

20 A

16 A

20 A

Note! The mains cable areas and fuse sizes as shown above are in accordance with Swedish

regulations. Use the welding power source in accordance with the relevant national regulations.

Note! The welding power source is designed for connection to a 230 / 400 volt

system with four conductors.

If the power source is to be used in countries with a higher supply voltage, the power

source must be connected via a safety transformer.

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

-- 8 --

bt31d1ea

6.1 Connections and control devices

1Control panel,

see separate instruction manual

5Connection for return cable

2Mains voltage switch 6Connection for welding cable or welding

torch

3Connection for shielding gas 7Connection for start signal from the

welding torch

4CAN connection for cooling unit or remote

control unit

8Connection for gas to the torch

6.2 Key to symbols

MMA TIG Return clamp

6.3 Fan control

The power source has a time control that means that the fans continue to run for 6.5

minutes after welding has stopped, and the unit switches to energy--saving mode.

The fans start again when welding restarts.

The fans run at reduced speed for welding currents up to 110 A, and at full speed for

higher currents.

6.4 Overheating protection

The welding power source has overheating protection that operates if the

temperature becomes too high. When this occurs the welding current is interrupted

and a fault code is displayed on the control panel.

The overheating protection resets automatically when the temperature has fallen.

-- 9 --

bt31d1ea

7 MAINTENANCE

Regular maintenance is important for safe, reliable operation.

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself

attempts any work in the product during the guarantee period in order to rectify any

faults.

Maintenance must be executed by a professional.

Only those persons who have appropriate electrical knowledge (authorized

personnel) may remove the safety plates.

7.1 Inspection and cleaning

Power source

Check regularly that the welding power source is not clogged with dirt.

How often and which cleaning methods apply depend on: the welding process, arc

times, placement, and the surrounding environment. It is normally sufficient to blow

down the power source with dry compressed air (reduced pressure) once a year.

Clogged or blocked air inlets and outlets otherwise result in overheating.

Welding torch

The welding torch’s wear parts should be cleaned and replaced at regular intervals in

order to achieve trouble--free welding.

8 FAULT--TRACING

Try these recommended checks and inspections before sending for an authorised

service technician.

Type of fault Corrective action

No arc. SCheck that the mains power supply switch is turned on.

SCheck that the welding current supply and return cables are

correctly connected.

SCheck that the correct current value is set.

The welding current is

interrupted during welding.

SCheck whether the overheating protection has operated (fault

code E6 is displayed on the control panel).

SCheck the mains power supply fuses.

The overheating protection trips

frequently.

SMake sure that you are not exceeding the rated data for the

welding power source (i.e. that the unit is not being

overloaded).

Poor welding performance. SCheck that the welding current supply and return cables are

correctly connected.

SCheck that the correct current value is set.

SCheck that the correct electrodes are being used.

SCheck the mains power supply fuses.

-- 1 0 --

bt31d1ea

9 ORDERING SPARE PARTS

Tig 3000i AC/DC is designed and tested in accordance with the international and Euro-

pean standards IEC/EN 60974--1, 60974--3 and EN 60974--10. It is the obligation of the

service unit which has carried out the service or repair work to make sure that the pro-

duct still conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page of

this publication.

Autres manuels pour Origo Tig 3000i

Table des matières

Autres manuels ESAB Système de soudage

ESAB

ESAB 100i Manuel utilisateur

ESAB

ESAB Aristo Mig C3000i Manuel utilisateur

ESAB

ESAB 653 cvcc Manuel de référence

ESAB

ESAB m3 Plasma EPP-202 Manuel utilisateur

ESAB

ESAB Rogue EM 125 Manuel utilisateur

ESAB

ESAB LTR 160 Manuel utilisateur

ESAB

ESAB 653 cvcc Manuel utilisateur

ESAB

ESAB Multimaster-260 Manuel du propriétaire

ESAB

ESAB Rogue ES 130i PRO Manuel utilisateur

ESAB

ESAB LHF 400 Manuel utilisateur

ESAB

ESAB ESABMig C420 Manuel utilisateur

ESAB

ESAB Warrior 400i CC/CV Manuel utilisateur

ESAB

ESAB Cutmaster 100 Manuel utilisateur

ESAB

ESAB Origo Feed 302N P0 Mode d’emploi

ESAB

ESAB Heliarc 161 Manuel utilisateur

ESAB

ESAB PCM-875 Manuel utilisateur

ESAB

ESAB MultiMaster 160 Manuel utilisateur

ESAB

ESAB Caddy Tig 1500i VRD Manuel utilisateur

ESAB

ESAB R-50 Series Manuel utilisateur

ESAB

ESAB LKB 265 Manuel utilisateur

ESAB

ESAB MEK 4 Manuel utilisateur

ESAB

ESAB Caddy Arc 151i Manuel utilisateur

ESAB

ESAB Warrior 400i MV CC/CV Manuel utilisateur

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur