ESAB Miggytrac B501 Manuel utilisateur

Instruction manual

0463 404 101 GB 20181102

Valid for: B501:serialno.1847xxxx,

B5001:serialno.1847xxxx

Miggytrac™B501,

Miggytrac™B5001

TABLE OF CONTENTS

0463 404 101 © ESAB AB 2018

1SAFETY ....................................................................................................... 5

1.1 Meaning of symbols ............................................................................... 5

2INTRODUCTION.......................................................................................... 9

3TECHNICAL DATA ...................................................................................... 10

4INSTALLATION............................................................................................ 11

4.1 Assembly ................................................................................................ 11

4.2 Adjust the front arm ............................................................................... 11

4.3 Install the battery.................................................................................... 12

4.4 Torch mounting ...................................................................................... 13

4.5 Install the magnet kit (optional) ............................................................ 13

5OPERATION ................................................................................................ 15

5.1 Weld operation........................................................................................ 15

5.2 Start and stop of the Miggytrac™ B501 tractor ................................... 15

5.3 Operation of the Miggytrac™ B5001 tractor ........................................ 16

5.3.1 Connections and control devices ......................................................... 16

5.3.2 Setting panel including colour display .................................................. 16

5.3.3 Menu selection ..................................................................................... 17

5.3.4 Selection of units of measure ............................................................... 17

5.3.5 Setting of functions............................................................................... 18

5.3.6 Installation of wire feeder ..................................................................... 20

6MAINTENANCE........................................................................................... 21

6.1 Daily maintenance.................................................................................. 21

6.2 Weekly maintenance .............................................................................. 21

7ORDERING SPARE PARTS ........................................................................ 22

DIMENSION DRAWING....................................................................................... 23

ORDERING NUMBERS....................................................................................... 25

ACCESSORIES ................................................................................................... 27

Rights reserved to alter specifications without notice.

1 SAFETY

0463 404 101 -5- © ESAB AB 2018

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and Safety

Data Sheets (SDSs).

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0463 404 101 -6- © ESAB AB 2018

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0463 404 101 -7- © ESAB AB 2018

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

If the maximum operating temperature of the battery (+60 °C) is exceeded, there

is a high risk of explosion!

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be potential

difficulties in ensuring electromagnetic compatibility of class

A equipment in those locations, due to conducted as well

as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation

in accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be

disposed of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

1 SAFETY

0463 404 101 -8- © ESAB AB 2018

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0463 404 101 -9- © ESAB AB 2018

2 INTRODUCTION

The Miggytrac™B501 and Miggytrac™B5001 are designed for MIG/MAG welding of plates

and beams.

The Miggytrac™B501 and Miggytrac™B5001 are compact tractors on which a welding

torch can be fitted. Both tractors can be powered with 18VDC from a lithium-ion battery. The

Miggytrac™B5001 can also be powered with 42VAC from a welding power source. The

tractors are equipped with four wheel drive for good traction and a high torque stepper motor

for stable welding speed. The Miggytrac™ is intended for welding with 4-stroke control mode.

As an option there is an easy fit magnet kit. The magnet kit can be attached at the bottom of

the tractor to further stabilize the movement when welding slopes up to 45°.

A battery and a battery charger are not included in the delivery, refer to the "ACCESSORIES"

chapter in this manual.

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

3 TECHNICAL DATA

0463 404 101 - 10 - © ESAB AB 2018

3 TECHNICAL DATA

Miggytrac™ B501 and Miggytrac™ B5001, from serial no. 1847xxxx

Miggytrac™ B501 Miggytrac™ B5001

Battery voltage (lithium-ion) 18 V DC

External supply voltage –20–50 V AC

24–70 V DC

Battery operating time 6–8 hours 4–6 hours

Motor type Stepper motor

Welding speed 10–130cm/min

(4–51in./min)

2–170cm/min

(1–66in./min)

Travel speed step welding –250cm/min

(99in./min)

Length step welding –1–99cm

(0.1–19.9in.)

Crater pause – 0–5.0 s

Backfill – 0–50mm (0–2.0in.)

Preheat – 0–5.0s

Remote volt and wire feed speed – 10–95%

Mechanical adjustments:

Horizontal slide ±32 mm (±1.3in.)

Vertical slide ±40mm (±1.6in.)

Guide wheel arms ±40mm (±1.6in.)

Maximum operating temperature:

Battery +60°C (140°F)

Carriage +80°C (176°F)

Drive wheels +150°C (302°F)

Horizontal tensile force:

Without magnets 12kg (26lb)

With magnets 25kg (55lb)

Vertical tensile force at 45° with magnet 11kg (24lb)

Maximum drive angle with magnet kit 45°

Dimensions (l×w×h) 310×290×250mm

(12.2×11.4×9.84in.)

310×290×340mm

(12.2×11.4×13.4in.)

Weight 12kg (26lb) 13kg (29lb)

Autres manuels pour Miggytrac B501

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ESAB Système de soudage

ESAB

ESAB YardFeed 200 Manuel utilisateur

ESAB

ESAB PowerCut 1300 Manuel utilisateur

ESAB

ESAB ST-21M Manuel utilisateur

ESAB

ESAB MEK 4 Manuel utilisateur

ESAB

ESAB MobileFeed 301 AVS Manuel utilisateur

ESAB

ESAB Caddy Tig 1500i Manuel utilisateur

ESAB

ESAB Origo Arc 4001i Manuel utilisateur

ESAB

ESAB ESP-50 Manuel utilisateur

ESAB

ESAB Rogue ES 180i Pro Manuel utilisateur

ESAB

ESAB A22 POB Instructions d'utilisation

ESAB

ESAB SR-B 9 Manuel utilisateur

ESAB

ESAB MIG 301i Manuel utilisateur

ESAB

ESAB Aristo Mig U5000i 400 V Manuel utilisateur

ESAB

ESAB Renegade VOLT ES 200i Manuel utilisateur

ESAB

ESAB Miniarc 150 Manuel utilisateur

ESAB

ESAB 0700300989 Manuel utilisateur

ESAB

ESAB Origo Mig 3001i Manuel utilisateur

ESAB

ESAB PCM-750i Manuel utilisateur

ESAB

ESAB EMP 255ic Manuel utilisateur

ESAB

ESAB Aristo YardFeed 2000 Manuel utilisateur

ESAB

ESAB CaddyTig HF Manuel utilisateur

ESAB

ESAB Aristo Mig 5000iw WeldCloud Manuel utilisateur

ESAB

ESAB MobileFeed 300 AVS Manuel utilisateur

ESAB

ESAB TAF 801 Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur