ESAB Aristo YardFeed 2000 Manuel utilisateur
Aristo®, Origo™
Instruction manual
0459 936 301 GB 20170831 Valid for: 425-xxx-xxxx, 616-xxx-xxxx
YardFeed 2000
TABLE OF CONTENTS
0459 936 301 © ESAB AB 2017
1SAFETY ......................................................................................................... 4
1.1 Meaning of symbols ................................................................................. 4
1.2 Safety precautions ................................................................................... 4
2INTRODUCTION............................................................................................ 8
2.1 Equipment ................................................................................................. 8
2.2 Control panel ............................................................................................ 8
3TECHNICAL DATA ........................................................................................ 9
4INSTALLATION.............................................................................................. 10
4.1 Lifting instructions ................................................................................... 10
5OPERATION .................................................................................................. 11
5.1 Connections and control devices ........................................................... 12
5.2 Function explanations ............................................................................. 12
5.3 Setting the wire feed pressure ................................................................ 14
5.4 Replacing and inserting wire................................................................... 14
5.5 Changing feed rollers............................................................................... 14
6MAINTENANCE............................................................................................. 15
6.1 Inspection and cleaning........................................................................... 15
7ORDERING SPARE PARTS .......................................................................... 16
DIAGRAM ............................................................................................................. 17
ORDERING NUMBERS........................................................................................ 19
WEAR PARTS....................................................................................................... 20
ACCESSORIES .................................................................................................... 22
Rights reserved to alter specifications without notice.
1 SAFETY
0459 936 301 -4- © ESAB AB 2017
1 SAFETY
1.1 Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and Safety
Data Sheets (SDSs).
1.2 Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
1 SAFETY
0459 936 301 -5- © ESAB AB 2017
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Wire feeders are intended to be used with power sources in MIG/MAG mode
only.
If used in any other welding mode, such as MMA, the welding cable between wire
feeder and power source must be disconnected, or else the wire feeder becomes
live or energized.
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing
• Insulate yourself from work and ground.
• Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
• Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
• Exposure to EMF may have other health effects which are unknown.
• Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or
work cable around your body. Keep welding power source and
cables as far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes
• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area
1 SAFETY
0459 936 301 -6- © ESAB AB 2017
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing
• Protect bystanders with suitable screens or curtains
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.
MOVING PARTS - Can cause injuries
• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
• Stop engine before installing or connecting unit.
• Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby
• Do not use on closed containers.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of class
A equipment in those locations, due to conducted as well
as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment and its implementation
in accordance with national law, electrical and/or electronic
equipment that has reached the end of its life must be
disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
1 SAFETY
0459 936 301 -7- © ESAB AB 2017
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
2 INTRODUCTION
0459 936 301 -8- © ESAB AB 2017
2 INTRODUCTION
The wire feed unit YardFeed 2000 with control panel U6 or MA23, is intended for MIG/MAG
welding together with Aristo / Origo welding power sources.
It comes in different variants, see chapter "ORDERING NUMBERS".
The wire feed unit contains a four-wheel drive wire feed mechanism as well as control
electronics.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1 Equipment
The wire feed unit is supplied with:
• Instruction manual for the wire feed unit
• Instruction manual for the control panel
Instruction manuals in other languages can be downloaded from the website,
www.esab.com.
• Decal with recommended wear parts
• Gas flow meter
2.2 Control panel
U6
With knobs for setting the voltage and wire feed speed /
current. Other settings by pushbuttons, with text indication on
the display panel.
MA23 Knobs for setting the voltage and the wire feed speed / current.
Other settings with push buttons.
See the separate instruction manual for a detailed description of the control panel.
3 TECHNICAL DATA
0459 936 301 -9- © ESAB AB 2017
3 TECHNICAL DATA
YardFeed 2000
Mains voltage 42 V 50-60 Hz
Power requirement 180 VA
Motor current Imax 3.5 A
Wire feed speed 0.8 -25.0 m/min
Torch connection EURO
Max. diameter wire bobbin 200 mm
Wire dimension
Fe
Ss
Al
Cored wire
0.6 - 1.2 mm
0.6 - 1.2 mm
1.0 - 1.2 mm
0.8 - 1.2 mm
Operating temperature -10 to + 40° C
Weight 11.3 kg
Dimensions (l x w x h) 593 x 210 x 302 mm
Shielding gas
max pressure
All types intended for MIG/MAG welding
5 bar
Type of cooling
max pressure
50% water / 50% mono-ethylene glycol
5 bar
Maximum permissible load at
60% duty cycle
365 A
Enclosure class IP23
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
4 INSTALLATION
0459 936 301 - 10 - © ESAB AB 2017
4 INSTALLATION
The installation must be carried out by a professional.
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to Sscmin at the interface point between the user's
supply and the public system. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with a short-circuit
power greater than or equal to Sscmin. Refer to the technical data in the
TECHNICAL DATA chapter.
WARNING!
When welding in an environment with increased electrical danger, only power
sources intended for this environment may be used. These power sources are
marked with the symbol .
4.1 Lifting instructions
Autres manuels pour Aristo YardFeed 2000
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels ESAB Système de soudage
ESAB
ESAB A6 Mastertrac Tandem Manuel utilisateur
ESAB
ESAB Origo Mig 4002c Manuel utilisateur
ESAB
ESAB Origo Arc 456 Series Mode d’emploi
ESAB
ESAB LHJ 425 Manuel utilisateur
ESAB
ESAB Aristo Origo Feed 3004 Manuel utilisateur
ESAB
ESAB LAW 510 Manuel utilisateur
ESAB
ESAB MIGMASTER 250 Manuel utilisateur
ESAB
ESAB Rustler EM 201C Manuel utilisateur
ESAB
ESAB TIG 401iW Manuel utilisateur
ESAB
ESAB PKB 250 Manuel utilisateur
ESAB
ESAB ET 210iP Advanced Manuel utilisateur
ESAB
ESAB fabricator 141i Manuel utilisateur
ESAB
ESAB 350mpi Manuel utilisateur
ESAB
ESAB Rogue EM 190 PRO Manuel utilisateur
ESAB
ESAB HandyPlasma 550 Guide de configuration
ESAB
ESAB Caddy Mig C200i Manuel utilisateur
ESAB
ESAB POWERCUT-1500 Manuel utilisateur
ESAB
ESAB MIGMATIC 250 Manuel utilisateur
ESAB
ESAB Mig 4004i Manuel utilisateur
ESAB
ESAB CUTMASTER A60 Manuel utilisateur
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
Elettro
Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur
